similar to: TDM 400P in Malaysia

We are setting up an office in Malaysia. We contacted Telekom Malaysia and are surprised to be told that ISDN-30 is no longer available. They are yet to give us information of the replacement technology. Does anyone have any experience and information with this? Thanks in advance.

A not so technical friend in India is shopping for a laptop. He often travels and stays months in Malaysia and so needs to be able to use the laptop there as well. He typically connects to the internet via wifi, but sometimes must use a telephone line (yes, with a modem). And of course there will be times when he has to plug into mains power to recharge the battery. So to be able to fully use

Anyone configured a E1 PRI in Kuala Lampur, Malaysia with TM Malaysia? What signaling did they provide, framing, formatting? primary-4ess Lucent 4ESS switch type for the U.S. primary-5ess Lucent 5ESS switch type for the U.S. primary-dms100 Northern Telecom DMS-100 switch type for the U.S. primary-dpnss DPNSS switch type for Europe primary-net5 NET5 switch type for UK,

Greetings from Hack in The Box -- We are pleased to announce that the Call for Paper (CfP) for HITBSecConf2006 - Malaysia is now open! Set to take place from September 18th - 21st 2006 at The Westin Kuala Lumpur, this years conference promises to once again deliver an International deep-knowledge security conference. HITBSecConf has been described as "the most intimate of hacker

Are there any other relatively low cost analog cards available? I'm interested in finding something that might work a bit more reliably than the TDM-400P.... regards, Paul -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050213/d772539e/attachment.htm

Hi all, I have a Digium TDM 400P at several locations. Once and again I'll need to restart the drivers because there is no ringing. Does anyone know a fix for this problem? Greatings Johan -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050906/66d9f13a/attachment.htm

Hi everybody, I have 3 TDM400P installed in a machine,and though the 4 ports of the first card work fine, some ports on the other two have low or no signal and a noise instead. Can someone help? Thanx __________________________________ Do you Yahoo!? Exclusive Video Premiere - Britney Spears http://launch.yahoo.com/promos/britneyspears/

It is a cable 4-5 meters long that has handssets connected I don't think its a matter of a distance __________________________________ Do you Yahoo!? Exclusive Video Premiere - Britney Spears http://launch.yahoo.com/promos/britneyspears/

Has anyone figured out how to power a Digium TDM 400P card in a Dell 1750 server? I opened the server and noticed that there is no access to 4 pin power to power the card. Is there some sort of adapter that I need to power the Digium card in a Dell Server? I see that the 1750 is listed on the Wiki. How have others powered the TDM400P in a Dell 1750?

Hi, I'm just starting out with Asterisk, in combination with a TDM400, filled with 2 FXS on channels 1 and 2, and 1 FXO on 4. Having just started, all I want right now is to be able to answer incoming calls on a phone connected to channel 1. The trouble is the caller id. I have caller id enabled on my line, my phone supports it, and when I connect the phone directly to the line, it works.

(Sorry of this appears in the list twice, but I wasn't sure if it was blocked or not) Hi there, I'm having a problem with my TDM-400P which has been working like a charm up until very recently. It started to fail last week, and so I was hoping someone could illuminate me with some information as to why. Its configuration is as follows: ------------ FXS (green) module is in position 1,

Greetings from sunny Malaysia! This is a reminder that the Call for Papers for the upcoming HITBSecConf2007 - Malaysia is closing on the 1st of May. HITBSecConf2007 - Malaysia is set to take place from the 3rd till the 6th of September in Kuala Lumpur. Our event last year attracted over 600 attendees from all corners of the globe and this year we are expecting this number to grow to well over

Merci pour la transmission de cet appel ?? tous ceux et celles qui pourraient y ??tre int??ress??s Conf??rence Internationale HMI 2013 Nous avons le plaisir de vous annoncer que l'unit?? de recherche SETIT et son partenaire l'ASDF viennent de conclure un accord. Cet accord pr??voit l'octroi d'une bourse d'un montant de 150$ et l'h??bergement gratuit (5 nuit??es) ?? tous

Hi all, I have TDM2406E with 24FXO ports connecting to 10 POTS line sitting in my office. the out going calls symptom like when called party pickup the phone but the calling party still hearing the ring tone from the IP phone. Please light me up. it been many sleepless night by googling around trying to get the right answers. The digium card running on Intel 915G chipset. Below are my zaptel

Ah, I thought you missed in my earlier reply the part about a bug with debug printouts in 2.8.0 (fixed on master since), did not comment on that when you replied with quoting... So, for now options are to bump debugging to 3+ or to build your own in one of many ways possible :\ On Wed, Jul 5, 2023, 06:23 Karl Schmidt <karl at lrak.net> wrote: > On 7/4/23 10:01PM, Jim Klimov wrote: >

I'm running a TDM-400P with 2 x FXS and 2 x FXO. I'm finding that there seems to be an odd relationship to sound quality on the card to my local when connecting via a SIP client. When I'm on my local network, if I connect to Asterisk via a SIP client (such as x-pro), and dial an outside line through the card, sound quality seems quite good. However, when I'm at a remote

On 7/5/23 03:17AM, Jim Klimov wrote: > Ah, I thought you missed in my earlier reply the part about a bug with debug printouts in 2.8.0 (fixed on master since), > did not comment on that when you replied with quoting... So, for now options are to bump debugging to 3+ or to build > your own in one of many ways possible :\ I think I'm not following you - with debug 3 -->> it

Hi I have had a TDM400p for a year now, recently I have been having problems with 'static' noise completely drowning out a call ( inbound only not on outbound calls)., has anyone else experience this and able to offer a solution. Also on inbound calls for the first 1/2 second or so I get a 'ray' gun sound and a bit of static then the call settles down and is usable any advice

Using a TDM400P in the UK nearly works fine, but I have a last remaining problem in that if the incoming is ringing and then the caller hangs up, asterisk takes another couple of rings before it spots the hangup. This is annoying in that I sometimes get phantom calls late at night (possibly due to call waiting or the exchange doing a half ring to see if we are live). Also I get phantom calls

A bit about my experience with the TDM-04 FXO. Only saw a few post on this subject, thought I would contribute a little about my experience to save others the hassle. a. As an earlier poster noted, the driver for the FXO is in the wcfxs module. Perhaps it should be renamed to something less confusing. b. You need the zaptel,zapata libraries from the cvs, the ones with Asterisk 0.7.2 won't