similar to: Outbound problem sip chanel

Hello, I have a TDM400 and currently have 2 of the ZAP Trunks configured on it. Zap/1-1 and Zap/2-1. I am Running Asterisk@home Version 2.4 with AMP version 1.10.010 In my Outbound Routing I have the Trunk Sequence set up so that 0 is Zap/1-1 and 1 is ZAP/2-1 What I see is that when Trunk Sequence 0 is full, it does not open Trunk Sequence 1. I have found that this is true even if I

hi i've configured a TE205P on asterisk at home this is my zaptel.conf span=1,0,0,ccs,hdb3,crc4,yellow span=2,0,0,ccs,hdb3,crc4,yellow bchan = 1-15, 17-31 dchan = 16 bchan = 32-46,48-62 dchan = 47 loadzone = it defaultzone = it and my zapata.conf signalling=pri_cpe ; pri_cpe = PRI slave ; pri_net = PRI master switchtype=national usecallerid=yes hidecallerid=no callwaiting=yes

Nik, Just curious - what is your telco setup? Do you have PRI with the specified D channels? You need to make sure that your telco is set up to have the D channels on 16 and 47. When you first start Asterisk, or when you log on to the CLI, do you ever see messages stating the B channels are successfully started? Let us know. -MC -----Original Message----- From:

I have an analogue trunk to an AT&T Definity. It has a DISA context defined. From a Definity handset call the analogue port extension 1008 and wait for dial tone from asterisk. It takes between 3&4 rings. Likewise from Asterisk SIP handset <PBX Access No><PBX Extn> takes nearly 10 secs to ring. Is this configurable? Ian Cowley -----Original Message----- From:

Skipped content of type multipart/alternative-------------- next part -------------- asterisk1*CLI> soft hangup Zap/1-1 Requested Hangup on channel 'Zap/1-1' == Spawn extension (macro-exten-vm, s-BUSY, 2) exited non-zero on 'Zap/1-1' in macro 'exten-vm' == Spawn extension (ext-local, 220, 1) exited non-zero on 'Zap/1-1' -- Hungup 'Zap/1-1' --

Hello, I have setup a test server with asterisk/AMP and have several 7960's connected to it. The asterisk server has a public ip and all the 7960's are behind nat'd routers. When I try to call from extension to extension I get directed straight to voicemail. I do not have any cards installed and instead direct everything to an Ondo server. I have been told it's not an AMP

Hi Folks, I'm have Asterisk version 1.2.1 with a A101 PRI card. I'm working with the CLEC to bring up the PRI and inbound calls are hanging up at his end after a few seconds. I ran PRI debug but it only gives me minimal insight. " Ext: 1 Cause: Unknown (16), class = Normal Event (1)" He ran a trace and the only difference he is seeing is a "ISDN interface explicitly

Hi, sorry for the long debug output below. I configured Asterisk with AMP to send the whole number including the extensions of the callers to the called party. Whatever I configure in AMP it looks like it is used, In my eyes it is ok, but doesn't seem to work. 033811234451 is the call id i configured, and it seems to use them, but the caller will only see a 0338189040 instead of my

Have asterisk@home 1.2.1 The server is on an internal network eg 10.10.10.10 It is NAT'd 1:1 via Checkpoint firewall to external public IP eg 50.50.50.50 The remote IAX2 phone (ATCOM320) is configured to call 50.50.50.50 on extension 1055. Outbound calls to 1055 work perfectly. Inbound calls from 1055 get picked up as if it were an external call (see below) and goes straight to the ring

Hi, I use: Trixbox-2.2.4 FreePBX-2.3.1.0 Asterisk-1.2.17 BRIstuffed-0.3.0-PRE-1y-e Zaptel-1.2.19 ..with two ISDN cards, often but occasionally the dial out failed but is possible to receive external call. My zapata.conf conf is: [trunkgroups] [channels] language=it context=from-pstn signalling=bri_cpe_ptmp rxwink=300 pridialplan=unknown prilocaldialplan=local switchtype=euroisdn

Hello, Sometimes the call gets answered for 1 second, but actually the phone has not rang, it?s just the CDR, and asterisk hangup automatically, I cought the log of 1 call like this, I hope you can help me with this. My setup is : <vendor> ----SIP--? <Asterisk> ?----IAX2---? <Asterisk with Dhadi channels> Here: -- Executing [966505103150 at from-internal:1]

Hi i have installed AAH 2.6 and configured some extensions the calls are working fine. but if i dont answer a call then it says " the person at extension " and hangs up . it doesnt spell out the extesion number nor it goes to voice mail box. *************************** Asterisk CLI log **************************** dialparties.agi: Extension 200 is available...skipping checks --

I've a call center using IAX softphones provided by a third party. We've observed problems where the IAX phones seem unable to use our PRI trunks. A sample anonymized call is provided below with the PRI debug calls embedded. Any thoughts, comments or suggestions would be welcome. In anonymizing it, I preseved the format and number of digits sent. -- Accepting AUTHENTICATED

Ok, I've been trying to figure out why my A@H won't answer the lines when I can call out and the panel shows the call coming in - well something bizarre has happened. I set up inbound routing to ring my extension if a call comes in - and my extension rings but when I pick it up I get a dial tone. The whole time after I answer I hear the phone I originated the call on just ring and ring

Ok, I've been trying to figure out why my A@H won't answer the lines when I can call out and the panel shows the call coming in - well something bizarre has happened. I set up inbound routing to ring my extension if a call comes in - and my extension rings but when I pick it up I get a dial tone. The whole time after I answer I hear the phone I originated the call on just ring and ring

Dear All, I have an asterisk server version 1.2.12.1 along with trixbox and I am having this nasty problem, I have a TE200P and have an E1 pri attached to it and zttool says it's OK, I have configured the whole 31 channels into one group as follow: Zapata-auto.conf: callerid=asreceived signalling=pri_cpe switchtype=euroisdn context=from-zaptel group=0 channel=>1-15,17-31

Is there a protocol I'm supposed to use here? It seems that people are asking 100 questions a day and SOMEONE is helping them, and I've posted this three times and not even an "I Don't Know". My third repost: Ok, I've been trying to figure out why my A@H won't answer the lines when I can call out and the panel shows the call coming in - well something bizarre has

Hello everybody, and first of all sorry for my poor English. I'm having trouble with Quadbri installed on Asterisk 1.2.17-BRIstuffed-0.3.0-PRE-1y-e. Everything is working fine, except calling to switched off or "out of coverage" cell phones. In this case I have to wait 40 seconds until Asterisk tell me that "all circuits are busy now" instead of receive cell phone

I have call center PCs that switch between an IBEAM SIP softphone and a NEBU IAX softphone (for reasons that aren't germane here). The SIP softphones work fine, but the IAX softphones get a fast busy unless I give them an IAX trunk to use, instead of the PRI trunks that all the other phones are using. I am using Asterisk 1.2.3. svn rev 47264. I've appended a sample call trace. The

I have Asterisk 1.2.29, Zaptel 1.2.24 and Freepbx Setup for a queue up to 15 agents through a PRI line, it was working fine for more than 1 year, suddenly, when there is a load on the queue, the asterisk service disconnects and the calls are dropped. And the service starts again after few seconds, and so on. I am not using fax. I checked PRI by zttool and there are no alarms. The cdr logs