similar to: Send flash through zap channel

> Hi all, Hi Marco, > I was thinking about integrating an old PBX with Asterisk and I was wondering > some possible configurations. You didn't mention the number of lines your PBX uses, but think of a third scenario: Install an asterisk with twice the number of BRI/PRI-Ports your current PBX has. Connect half of them to your carrier, the other ones to your old PBX (Some sort of

Hi, > I've never run against a commercial PBX that didn't need > maintenance. Acknowledged. > VM hard > drives fail, > ... > Asterisk is > every bit as stable > as the old-gen KSUs and PBXs. There are big differences. As I know of no other PBX that uses 'consumer' hardware, asterisk is also struggling with problems in the underlying Hardware. And

For all the peoples that wanted to test my windows IAX2 phone, I've put it up on a server where it can be downloaded. For the ones that wanted the DLL, it's available on the same page. For the DLL, I will post a list of the functions in it and the parameters it expect as soon as I have some free time. All comments (good or bad) are welcome The phone can be used mostly with the keyboard

Hi all, I have just been reading an article on the asterisk-doc site about ISDN X-Over cables. The article mentioned the converting of an NT1 to make this possible, has anybody got the information required to modify a BT NT1? Or any information on the BT NT1. Thanks in advance. Regards Dave

Hello, Is it possible to detect a hook flash in asterisk. I want to be able to perform some functions an hook flash. I have the following entry in features.conf which executes a Macro on detecting key press '**'. [applicationmap] test => **,caller,Macro,testflash Is it possible to do this action on hook flash? -------------- next part -------------- An HTML attachment was

I've read quite a bit in the older mailing list posts and the wiki but I'm missing some simple point. 1) What is required to send an SMS to a mobile outside the office given: Channel: ZAP/1 send it to $SMS_RECIPIENT (which includes the final "extra" digit) via $SMS_CENTER=the national message center server for sending messages $MESSAGE= the message text How is the .call file

Problem resolved. This makes it nice and simple to 'flash' an incoming POTS line (ZAP channel) as opposed to the dialplan scripts that I have seen that require tranferring the call, hanging up, and waiting for a call back. That was too confusing for my wife. Now all she has to do is pres *3 and it is done. No transfers. No hanging up. No dial back. extensions.conf [context] exten =>

I'm attempting to convert from ZAP to DAHDI with 1.6.0. I was using 1.6.0-beta9. I followed the directions I could find. I moved /etc/zapata to /etc/dahdi/system.conf I moved /etc/asterisk/zapata.conf to /etc/asterisk/chan_dahdi.conf I don't undestand how to deal with extensions.conf? I replaced Dial (ZAP/ ...) with Dial (DAHDI/ ... ) All my inbound calls from DAHDI work the same as

Does anyone know what this error message means? Unable to create channel of type 'DAHDI' (cause 0 - Unknown) I've upgraded to 1.6.0 with dahdi 2.0. For some reason my outbound dahdi calls are not going through. At some point, it starts to work, but I don't know what the trigger is. Out of the blue, outbound calls start to work. I had been using asterisk-1.6-beta9 with zaptel

I did ./configure make make install I got no errors, but it doesn't seem to have installed everything I need. Swat won't start. It didn't put an smb.conf file in /etc/samba (it didn't even create this folder) or /usr/local/samba/lib/. When I run testparm, I get Segmentation fault as my only output. Even if I create an smb.conf and run testparm on that file I get the exact

Hi, I hope someone could help me, i have a x100p interface for testing purpose and on each incomming call I redirect the call to handytone 388 atas, the problem comes when i'm during a call and another call comes in, i hear the call waiting beep (comming from the zap channel), but I can't catch the call as usually using flash+2 (my pstn call wait sequence), because when i flash the

Hello I have big problem. I have a couple komputers with Windows as a OS. I joined those machines to the domian, but always when I try to log in i see the message: Windows cannot load roaming profile. I know, maybe this is a wrong address I've mailed but - PLEASE HELP. PLEASE.

Hi, I'm trying to set a rule to dial out through multiple Zap groups so that, say, g0 is the cheaper POTS lines group and must be used first. However, if g0 is busy or disconnected then try dialing out g1. My g0 group is made up of 4 analog lines connected to a 4-FXO card. I disconnected the RJ-11 wires from the FXO card to simulate a line disconnection. So theoretically all calls should

I can now login to my domain from an XP Pro client, as a normal user. Only problem is, I get this: Windows cannot locate the server copy of your roaming profile and is attempting to log you on with your local profile. Changes to the profile will not be copied to the server when you logoff. Possible causes of this error include network problems or insufficient security rights. If this problem

I am banging my head over a simple asterisk trick I was seeing on one asterisk server. An extension dials an international premium number, the called number answers, then the extension hangups, but the call continue to run on the international number side, generating an high profit for the premium number company and a big loss for the asterisk owner. I think some sort of "transfer"

So far no one I have talked to has either had this issue or does not know a answer. I currently run asterisk 1.0.9. I have two issues to deal with. 1. The caller waiting caller ID does not show on the uniden hand held that is hooked to a sipura spa 1000 or my Polycom ip500. 2. When a caller is calling in and I hear the caller waiting beep on the line when talking with somone, is there no way

Hello, I am trying to install automatic printer driver download and install. I am running Samba 3, as a PDC, on RedHat 7.3. It seems everything is setup correctly, although I cannot get the rpcclient to 'see' my printer. Please notice these two printers listed below ar the same (lp & HP2300). [root@mercury log]# rpcclient -U=root localhost Password: rpcclient $> enumprinters

On Wed, Aug 8, 2018 at 1:53 PM, Daniel Journo <dan at keshercommunications.com> wrote: > > Prior to a call entering a Queue, I set __DYNAMIC_FEATURES=NewRecordApp. > > AgentA answers and is able to use that feature code. > > If AgentA performs an attended transfer of a call from a queue to > AgentB, the > > feature code no longer works. > > > > It only

Hi, I think I've identified an issue and just want to check before completing a bug report. Prior to a call entering a Queue, I set __DYNAMIC_FEATURES=NewRecordApp. AgentA answers and is able to use that feature code. If AgentA performs an attended transfer of a call from a queue to AgentB, the feature code no longer works. Cases that do work are as follows... Calls using both Queue() and

I have been trying for a very long time to get asterisk to detect and utilize dtmf tones from my sip clients within my dial scripts. I have set automon=>#9 in my features.conf, I have Dial(....,gWw) in my dial scripts. I have Set(DYNAMIC_FEATURES=automon) as the first script in my extension. I can see the dtmf tones on the wire as SIP INFO packets. Using the Read() app I have verified that * is