similar to: chan_capi setting ${DNIS}

I seem to be having a problem with B3 on my ISDN line, as you can see from the dial string I am having to have asterisk generate ringing else there is no progress indication. -- Executing Dial("SIP/0014A8ACCB83-fd9f", "CAPI/g1/142392203000/ b|40|r") in new stack -- Called g1/142392203000/b -- CAPI/ISDN1/142392203000-0 is proceeding passing it to SIP/

Hi everybody, I have a problem which I cannot eliminate on my own. Has anybody any idea for the following: I am using the asterisk-version from Debian-Testing (1.2.13) with the latest chan_capi (also tried an older version). When using the Capi-Channel, everything works fine except from the sound it sounds extremely choppy and is unusable :-( When e.g. capisuite is used for fax, everything

Hi, I am having a problem with (Asterisk is crashing) with a Fritz card PCI / chan_capi. Receiving Calls from PSTN works, but outbound calls make asterisk crash (Speicherzugriffsfehler/Segmentation fault). The crash occurs upon dialing with the other phone not even ringing. I hereby ask if somebody reading this list can confirm or disprove my issue. Does anbody run a recent asterisk 2.6 with

The subject pretty much says it all. Does Asterisk support DNIS, and if so, what kind of connection is required? (T1, PRI) I've got a wink start T1. I've read comments that say the DNIS will be seen as an extension, but I'm seeing each digit of the DNIS as a separate extension. So in my case I send DNIS of 12345, Asterisk will jump from extension 1 to extension 2 to extension 3 to

Hi i have an asterisk pbx with E1 port connected to another PBX. Im trying to send the DNID/DNIS to the PBX here's my dialplan exten => 8881111111,1,Dial(ZAP/g2) exten => 8881111111,n,Hangup() The PBX just get the number 2 as it's DNIS when i change it to ZAP/1 or ZAP/g1 the PBX get the number 1. What should i add to send the extension number as DNID/DNIS? Thanks! --------------

Hi! I am playing around with Asterisk and have a problem :-) (Asterisk-version: 1.2.4, chan_capi-cm-version: 0.6.4) I have a sip-phone at my desk and an ISDN-phone (independent of the Asterisk-server) in my living room, when I'm not at my desk, the sip-phone is switched off. I would like to be able to accept calls at both phones (when available) and have Voicemail kick in if I don't

1. If the other end picks up the phone the conversation is successful and when the conversation ends, the channel is properly released: -- CAPI/ISDN1#02/2104988888-0 answered SIP/1000-081d91b0 == ISDN1#02: CAPI Hangingup for PLCI=0x101 in state 2 == Spawn extension (internal, 2104988888, 1) exited non-zero on 'SIP/1000-081d91b0' > ISDN1#02: CAPI INFO 0x3490: Normal call

I have a problem receving calls via the ISDN line, using the followin components Asterisk 1.0.9 with asterisk@home chan_capi-cm-0.6 AVM Fritz card datalink protocol = point to multimode I can make calls out with no problems so the issue is only incoming calls. When I make the call from an external line to the ISDN line connected to asterisk, I get a busy signal after about 5 seconds. I have

Good Day list, Need assistance determining the best place to read up on whether Asterisk can help me out. I have a situation where I need to do the following <PRI from Telco> ------- <Analog Channel Bank>------------<Proprietary Box> | | | | | | <PRI Port 1 of Digium Quad T1> <PRI Port 2 of Digium Quad T1> | | | | | |

I installed a Sangoma card with the default install. I'm getting five digits of DNIS with each call. The T1 is setup ESF/B8ZS wink start. Each of the digits of the DNIS are being used for extensions in the context. I need a single extension that let me start an AGI script that can use the dnis. Can anyone point me in the right direction to do this? Thanks, David Ruggles CCNA MCSE (NT) CNA

Can someone in Asterisk'land subscribing to 800 service explain to me how to setup extension.conf to route calls based on the incoming DNIS/ANI. For example I want to route 3 incoming 800# coming across a trunk group to all land in the same queue. So I guess I am asking how to perform DNIS/ANI based call routing? -------------- next part -------------- An HTML attachment was scrubbed... URL:

does anyone know how to route a call coming in with ANI*DNIS* Oct 31 12:47:41 VERBOSE[30056] logger.c: -- Executing Set("Zap/49-1", "DID=1231234*4812*") in new stack I tried making a route for _.*4812* but that matched everything rather then just the dnis i wanted.. any ideas? I would preferably like pass the callerid along to my extensions, but for now the important

Hello Armin, hello List I'm trying to get chan_capi working with asterisk from debian stable (asterisk 1.0.7, the debian version number is 1:1.0.7.dfsg.1-2). I managed to get it compiled by providing my own version of ast_copy_string. This is an Austrian PTP line. I can do outgoing calls fine (no comprehensive tests yet). For incoming calls, I'm getting "No answer" on the

Hello, Being totally fed up with the lack of quality and reliability from both VoicePulse and BroadVoice, We are switching to a direct IP connection to Global Crossing. We've installed a local point-to-point T1 into their CO, and they will give/take SIP g729a directly and act as the gateway for us. In setting up the inbound SIP service, they are asking the question, "In what format do

My company is based in Australia and we have a need to be able to present CLI (ANI) and DNIS to an analog extension. Currently our PABX vendor is saying they can only deliver CLI between the first and second cadence. The system will collect calls via an aggregate of ISDN PRI services from the PSTN and then direct them to the analog extensions in a hunt group configuration. It is important that

I am trying to receive both CID and DNIS from the telco through a non-pri T1. Currently I have the T1 setup and operational both outbound and inbound calls are completed as should be expected. The calls came in and were placed in the context specified in zapata.conf on exten => s,1. I have requested that the telco provide callerid (they call it ANI) along with 10 digit dnis for my 800

I've having a big problem after having upgraded to 1.2.4 and chan_capi-cm 0.6.4 When making outgoing calls I don't seem to have any control over the CLI that is presented to the called party -- it can be any one of the MSNs allocated to the line, allocated on what seems to be a random basis. This is on a BT Business Highway line (which is essentially an ISDN2e line with two built-in

Situation: 8 POTS lines, 3 companies, 1 system. Channel banking the POTS lines onto a T1 thru an ADIT 600. The only way our carrier will provide DNIS is thru Analog DID #'s. Anyone know of a piece of hardware that can add DNIS digits to a particular line? -Darren

Hello, I have a noticed strange behavior in Asterisk 1.6.18.2 with ReceiveFax Digium FAX Driver: 1.6.2.0_1.3.0 (optimized for i686_32). I use a context [capi-in] for icoming ISDN calls: ====== [capi-in] ; Faxe fuer Ruben exten => 12345,1,Macro(faxin,ruben.roegels at jumping-frog.org,${EXTEN}) ====== My macro for the fax receiving looks like that: ====== [macro-faxin] ; Faxe ; ARG1 =

Hello everybody, i'm from Mexico, at the time i?m working on a production server with asterisk 1.2.25 + spandsp-0.0.4 + libmfcr2-0.0.3+libsupertone-0.0.2+libunicall-0.0.3 and zaptel-1.2.22. I installed this version of astunicall that i downloaded from http://www.moythreads.com/astunicall/ Everything works fine, i'm able to make outgoing calls and recive incoming calls with all ANI and