Displaying 20 results from an estimated 800 matches similar to: "[slackware 10.2 and TE205P] Unknown signalling method 'pri_cpe'"
2009 Feb 09
1
Noisy Ring Back Tone with TE205P card
Hi,
I am having problems with an Asterisk with a Digium TE205P card. The
issue is that the Ring Back Tone is noisy. I am making modem's calls and
this noise influences on the initial negotiation protocol, so modems
have to recall.
My configuration is:
Asterisk version: Asterisk 1.4.21.2
Linux version: CentOS release 5.2 (Final)
Card: Digium TE205P
2006 Jan 19
0
PRI
I am having problem with T1 configuration.
Following r the config..
Zaptel.conf
# Autogenerated by /usr/local/sbin/genzaptelconf -- do not hand edit
# Zaptel Configuration File
#
# This file is parsed by the Zaptel Configurator, ztcfg
#
# It must be in the module loading order
span = 1,1,0,esf,b8zs
# fxsks=1-24
bchan = 1-23
dchan = 24
# Span 1:
2006 Apr 10
3
E1 PRI problem with TE205P
Hi all,
I've setup a PBX in production environment last week but we have immediatly
find out drop conversations and lot of errors (in asterisk logs) like:
Apr 10 17:30:48 NOTICE[25154] chan_zap.c: PRI got event: HDLC Bad
FCS (8) on Primary D-channel of span 2
My configuration is:
Motherboard: SuperMicro P8SCT (Intel E7221 chipset)
Hypertrading and APIC enabled
CPU: P4 3GHz
Digium TE205P
2006 Mar 14
0
help required configuring card
Hii,
I've a Digium TE205P card and I'm running asterisk@home in a box.I want to configure this card in that box.But as it is a dual port card I'm not sure how to configure it in my box.By searching diffrent site I could able to make a sample configuration bellow I'm giving.Basically I want to connect one T1 connection in one port and in anather port of the card I'll
2010 Jul 08
1
not sure what to change to point the timing to the at&t circuits?
# Span 1
span=1,1,0,esf,b8zs
bchan=1-23
dchan=24
echocanceller=mg2,1-23
# Span 2
span=2,2,0,esf,b8zs
bchan=25-47
dchan=48
echocanceller=mg2,25-47
# Span 3
span=3,3,0,esf,b8zs
bchan=49-71
dchan=72
echocanceller=mg2,49-71
# Span 4
span=4,4,0,esf,b8zs
bchan=73-95
dchan=96
echocanceller=mg2,73-95
# Global
loadzone = us
defaultzone = us
Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1"
2007 Feb 28
7
Problem with TE212P
Hello.
I have a TE212 configured in E1 mode.
This is shown in a cat /proc/zaptel/2 and 3 (where the card is configured):
cat /proc/zaptel/2
Span 2: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" HDB3/CCS/CRC4 RED NOTOPEN
25 TE2/0/1/1 Clear
26 TE2/0/1/2 Clear
27 TE2/0/1/3 Clear
28 TE2/0/1/4 Clear
29 TE2/0/1/5 Clear
30 TE2/0/1/6 Clear
2010 May 31
0
Dahdi PRI T1 Setup for TE210P
Hello,
I have been struggling with the configuration of this card on my box.
I have a T1 line and I am trying to setup asterisk with it.
I followed all the instructions and I still see a blinking red light on the
card.
I use fedora 12.
If everything is fine should I see a green line when I plug in the T1 line ?
I want to isolate the issue so I di not start asterisk. When I run asterisk
I get
2012 Jan 03
1
ISDN E1, after electrical disconnected is not becoming UP, IRQ misses: 1
Dear All;
I am afraid from IRQ misses: 1
The ISDN E1 was working fine on the machine, the electrical disconnected and then the Red Allarm. I checked the dahdi and I found that I have to reinstall dahdi again and I did. But still not becoming UP.
The output of the cat /proc/dahdi/1 is following (I am afraid from the IRQ misses: 1, so if it is a problem what is the solution)?
[root at CC
2012 Jan 23
1
Timing Slips CRC & E-Bit Errors - Asterisk - Trixbox 2.8.0.4
Hi,
I've searched and searched on the possible problems. If anyone can help me
that would be great.
Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) B8ZS/ESF
CRC4 error count: 4750
E-bit error count: 5023
Timing slips: 72
1 TE2/0/1/1 Clear (In use) (SWEC: MG2)
2 TE2/0/1/2 Clear (In use) (SWEC: MG2)
3 TE2/0/1/3 Clear (In
2006 Feb 16
1
Problem making outbound calls on TE210P using NFAS
Hello,
I'm running Asterisk@home 2.5
asterisk 1.2.4
zapatel 1.2.2
libpri 1.2.2
on a Dell Poweredge 2850 (1 CPU) with a TE210P
I have 2 t1 circuits using NFAS with dchan on 24 and no backup dchan. I am able to receive inbound
calls on all channels and can only make outbound calls on channels 25-48.
Attempting to make an outbound call on channels 1-23 results in congestion.
2014 Jan 09
2
How to read IRQs and timing slips values
Hi,
On a Asterisk 1.8.12 system working OK for months (>100k calls proceed),
users are complaining for bad audio.
My setup is:
PSTN <--E1/PRI ---> Asterisk <--- E1/PRI---> Siemens HiPath <---E1/PRI
---> PSTN
asterisk -rx "dahdi show version"
DAHDI Version: SVN-trunk-r10414 Echo Canceller: HWEC
asterisk -rx "pri show version"
libpri version: 1.4.12
A
2005 Sep 28
2
TE205P in loopback?
2006 Mar 22
2
connecting Avaya Partnet with asterisk , TE205P
Hi ...,
I've a TE205P card installed in my asterisk box.Port 1 of my card is connected to service provider.From port 2 I want to connect Avay Partner system.
what type of cable I require to connect the partner system (straight/cross over). How the call routing from outside will be done to epbx.
Thanks inadvance
regards
rudra
-------------- next part --------------
An HTML attachment
2001 Sep 12
0
AES update..
I've done a decent size update of the OpenSSH portable from the upstream
tree. There is an AES upgrade that needs to take place, but I need people
to test and tell me what endedness changes need to be applied (if any).
Attached is the patch. It is geared towards the latter snapshots..Unsure
how it will patch (if at all) against 2.9pX series.
Thanks.
- Ben
"This is dark day in
2006 May 10
1
ISDN, TE205P, I'm goind crazy :>
Hi guys,
Currently I just purchased the TE205P for the installation of my ISDN30 setup. I
compiled, setup the card correctly I think. When I do the ztcfg -vvv it shows all 31
channels clear, with 30 bchannels using for voice ranging from 1-15, 17-31, and 16
is the dchannel. However, when I do a cat /proc/zaptel/1 I see only 24 channels
configured, and then, when I do a cat /proc/zaptel/2 I see
2006 Oct 26
1
PRI (TE205P) allways RED/NOP
I have a TE205P, jumpered for E1, added the missing wct4xxp-line to
/etc/modprobe.d/zaptel, zaptel.conf is just
span=1,1,0,ccs,hdb3,crc4,yellow
span=2,2,0,ccs,hdb3,crc4,yellow
bchan=1-15
dchan=16
bchan=17-31
bchan=32-46
dchan=47
bchan=48-62
Which, according to my reading of the documentation I could find, should be
correct. ztcfg doesn't complain about anything, yet all I ever get is RED
2008 Apr 02
1
TE205P
Hello,
I am working on a project and have a few questions. I want to connect
one port of the TE205p to the PSTN, and another port to the PRI port
of a PBX. Basically Asterisk will sit between the PSTN and the
existing PBX. Are there any gotcha's I need to be aware of? Will the
existing PBX be able to dial through asterisk as if it was a PSTN
connection?
--
Isaac McDonald
Got VoIP?
imcdona
2007 Apr 21
3
FAX on PRI and TE205P
Hi
i have a PRI connected to a TE205P.
Actually, can i send and receive FAX through Asterisk using stable solutions?
Or shall i connect an ATA to Asterisk and then a modem with Hylafax?
--
/*************/
nik600
https://sourceforge.net/projects/ccmanager
https://sourceforge.net/projects/nikstresser
2007 Apr 15
3
Digium TE205P and channelbank
Trying to find my feet here. If I wanted to connect Asterisk to a PRI and
throw in a T1 Adtran channel bank into the mix for fax machines would the
following work?
Connect PRI line from telco to Port 1 on the Digium Wildcard TE205P.
Connect Adtran TA-624-T1 to Post 2 on the Digium Wildcard TE205P
also, would I need a crossover to the channelbank or is it a patch lead
like the connection to the
2005 Sep 10
0
Problems with TE205P
I've been working with Digium, but hopefully someone on-list has an
idea...
The card will transmit audio to the T1, but everything it receives is
completely unintelligible static (in place of received audio only, not all
the time).
I've verified everything on Digium's troubleshooting checklist and they
were unable to find anything when they logged in. zttest yields 100% for
the