similar to: Alarmreceiver

Anyone using the AlarmReceiver? Does it work? Mine doesn't seem to communicate properly. How can I tweak the DTMF settings? Is it in the zaptel.conf or somewhere else?? -- Executing AlarmReceiver("Zap/1-1", "") in new stack > AlarmReceiver: Setting read and write formats to ULAW > AlarmReceiver: Answering channel > AlarmReceiver:

Hi, Did anyone try to set up alarmreceiver application over IP network? Which ATA can I use? I tried to set up it with Linksys PAP-2 but with no luck. Maybe I did something wrong with alarmreceiver.conf (I tried diverse settings, but nothing worked). Sometimes alarmreceiver is able to get some events but sometimes not. I think Linksys PAP-2 has a problem with recognizing digits in appropriate

Hi, Does anyone have some experience with Nokia 32 Terminal (it is an analog GSM Gateway)? After a configuration I can make only incoming calls, I'm not able to do any outgoing. Nokia signalize an error (4 short tones), when I try to phone someone. I tried postpaid simcards as well as prepaid simcards with the same result. Does anyone try to connect this gateway to Asterisk PBX if so what

Following is the last few lines of output when i try to launch Asterisk:- [app_zapscan.so] => (Scan Zap channels application) == Registered application 'ZapScan' [app_saycountpl.so] => (Say polish counting words) == Registered application 'SayCountPL' [func_cut.so] => (Cut out information from a string) == Registered custom function CUT == Registered custom

Hi Last friday I have upgraded to Asterisk 1.2.7.1 (bristuff-0.3.0-PRE-1p.tar.gz). Since that I have a problem with my Asterisk box. I am receiving these messages: May 24 09:30:11 asterisk kernel: zaphfc: empty HDLC frame or bad CRC received (framelen = 6, stat = 0xff, card = 2). May 24 09:30:12 asterisk kernel: zaphfc: empty HDLC frame or bad CRC received (framelen = 6, stat = 0xff, card = 2).

How do I set configure my voicemail notification so that when I'm left a voicemail message it: 1) sends an e-mail to my inbox with the voicemail message attached 2) sends a message to my cellphone without the message attached I get notifications when I've got attachments turned off, but my cell doesn't like attachments in the messages and doesn't send them. An even better

Can someone point me in the right direction to find documentation on best practices when setting up a new Asterisk server? I'm using RHES4 and Dell 1750 with TE412P. My current problems are frequent crashes and choppy audio so I think I can easily tweak these out of the picture. -------------- next part -------------- An HTML attachment was scrubbed... URL:

asterisk-users-request@lists.digium.com wrote: >Send Asterisk-Users mailing list submissions to > asterisk-users@lists.digium.com > >To subscribe or unsubscribe via the World Wide Web, visit > http://lists.digium.com/mailman/listinfo/asterisk-users >or, via email, send a message with subject or body 'help' to > asterisk-users-request@lists.digium.com > >You can

Is H323 built into the current CVS? If so, could someone give me an idea of a simple config? thanks, darran -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030429/fffec1d1/attachment.htm

Using trixbox (or a custom dialplan if needed) has anyone been able to convert a number dialled like +612421100000 to something like 024221100000 ie (remove the +61 and replace with 0) i just dont know how to set it up, there seems to be no dialplan wildcard i can use to match +. I was thinking of something like .61XXXXXXXXXX but that still seems wrong to me. it could match other numbers.

Hi, I've been struggling with this for a quite long time. Maybe I am not the first asterisk user with this problem, (I try to search on google, but I didn't find anything good). My point is: I try to set up * to work as a fax server. Each incoming fax (from PSTN) should be received on email. Luckily it works. I didn't notice any problem with receiving faxes on email, so rxfax works

Hello list, I have been running Asterisk CVS for a good while. When I try to install 1.0.3, asterisk won't start. Below are the last few lines of output before Asterisk crashes. I ran "make samples" to start with a fresh setup. [app_read.so] => (Read Variable Application) == Registered application 'Read' [app_alarmreceiver.so] => (Alarm Receiver for Asterisk) ==

Hello All, Recently I added some Nokia N95 customers and it worked pretty good. Now the customers are complaining about the dialing rules... They are used to dialing +12486543210 and +4479XXXXXX for long distance calls. Is there anyway to create a "+" sign dial plan which will allow them to dial a number with "+" sign. Cheers, Nitesh

Hi, I've brought this up in the past and there was a good discussion - am wondering if there have been any new developments. Our dialtone service, like I am sure is true for most ITSPs, touts the ability to drop your POTs lines for significant savings. For businesses we have a low-cost Atom based PBX and a "fax relay" setup locally with hylafax/iaxmodem to solve that issue,

Has anyone had any luck with PostgreSQL and Realtime? The realtime instructions on voip-info seem pretty straight forward... just not woking for me. I've included all of my config files below, and my console output. Entire console bootup output: [root@abox asterisk]# /usr/sbin/asterisk -vvvvvvc == Parsing '/etc/asterisk/asterisk.conf': Found == Parsing

Hi, I want to extend my asterisk stuff and buy some Planet devices, to be certain I'm going to buy PLANET VIP-050 with FXO and FXS modules. Has anyone heard about it. Is it compatible with Asterisk, or it would cause a lot of problems. Dose anyone have some experience with it?? All the best Andrutto ---------------------------------------------------------------------- Oferty sprzedazy

Hi, Ive been struggling with asterisk for a few days now. I understand pretty much how it works and how to tie things together (SIP -> SIP internally works fine etc), but just cannot get asterisk to work with an X100P clone (its a Ambient MD3200, if that means anything to you guys). I have tried (initially) asterisk 1.07 with zaptel 1.07, and now Asterisk CVS-HEAD with zaptel cvs. Both give

Hi All, Can anyone tell me what are the <dev1> <dev2> parameters that I should use to run pridump? I took a look at the source code but couldn't figure this one out. Best, PauloHM

I have a patton 1400 setup to handle the bri interface. As a trixbox user, I wanted a sip trunk rather than having to re-compile bri support into trixbix. Anyway, I have it working now so that asterisk can make calls and they are passed properly to the telephone network. Incoming calls however are another matter. I have (after turning on cli debug in the 1400) determined that its getting stuck

Hi, I finally found an ATA which works really well with asterisk and its application alarmreceiver. Frankly it works just like the TDM card. It is Soundwin S800 series ATA. Cheers Andrew -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060512/7f7175cf/attachment-0001.htm