similar to: problem with outgoing calls Unabletocreatechannel of type 'ZAP' (cause 34 - Circuit/channel congestion)

When Asterisk first starts up, it will attempt to "bring up" the B channels on any PRI circuits. If you are using A@H then you can log on to the Asterisk CLI (asterisk -r) and then do "stop now" to stop asterisk. Start up Asterisk again by typing asterisk -cvvv at the Linux command line. You should see a bunch of messages on the terminal and then you'll get the Asterisk

Nik, Looks like you're making some progress. When I first started using A@H I had trouble getting the outbound dialing to work. I wasn't sure where to start, so what I did was skip the macros in the dial plan. I wanted to play around with exactly what digits the telco wanted to see. So I put a specific extension in my [default] context like this: exten =>

Nik, Just curious - what is your telco setup? Do you have PRI with the specified D channels? You need to make sure that your telco is set up to have the D channels on 16 and 47. When you first start Asterisk, or when you log on to the CLI, do you ever see messages stating the B channels are successfully started? Let us know. -MC -----Original Message----- From:

-----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of nik600 Sent: Saturday, February 18, 2006 2:00 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] problem with outgoingcallsUnabletocreatechannelof type 'ZAP' (cause 34 -Circuit/channelcongestion) On 2/17/06,

Nik, This definitely helps! Please check your dial command. You've got "Dial(Zap/0/mynumber)" and I think you might possibly want it to be something like this: Dial(Zap/1/mynumber) or Dial(Zap/g0/mynumber) I don't recall there being a zap channel zero, but it is common to have a group zero. I would recommend trying Zap channel 1 - Dial(Zap/1/mynumber) - before trying the

hi i've configured a TE205P on asterisk at home this is my zaptel.conf span=1,0,0,ccs,hdb3,crc4,yellow span=2,0,0,ccs,hdb3,crc4,yellow bchan = 1-15, 17-31 dchan = 16 bchan = 32-46,48-62 dchan = 47 loadzone = it defaultzone = it and my zapata.conf signalling=pri_cpe ; pri_cpe = PRI slave ; pri_net = PRI master switchtype=national usecallerid=yes hidecallerid=no callwaiting=yes

Just to share some experience with everyone about what happened today to our Asterisk 1.4 box with Digium TE412P card. We had an unscheduled power outage which shut down the Asterisk box. When the power went up, Asterisk came back up okay but the ports on the card were all red. Zttool show red alarm and cat /proc/zaptel/1 show red alarm today. Both incoming and outgoing cannot be made. When a

Hii, I've a Digium TE205P card and I'm running asterisk@home in a box.I want to configure this card in that box.But as it is a dual port card I'm not sure how to configure it in my box.By searching diffrent site I could able to make a sample configuration bellow I'm giving.Basically I want to connect one T1 connection in one port and in anather port of the card I'll

Hello, I'm running Asterisk@home 2.5 asterisk 1.2.4 zapatel 1.2.2 libpri 1.2.2 on a Dell Poweredge 2850 (1 CPU) with a TE210P I have 2 t1 circuits using NFAS with dchan on 24 and no backup dchan. I am able to receive inbound calls on all channels and can only make outbound calls on channels 25-48. Attempting to make an outbound call on channels 1-23 results in congestion.

Has anyone else installed the official 1.4.0 release? I have, and it installed very easily. However, I don't have any of my usual command line tools for monitoring and debugging zap channels and PRI lines: asterisk1*CLI> pri show span 1 No such command 'pri show' (type 'help' for help) asterisk1*CLI> Ditto with zap stuff: asterisk1*CLI> zap show

Hi I have this escenario: |SIP or H323 phone|---->|Cisco2600|----E1-pri---->|Asterisk|------>IVR, A2Billing, etc... The problem is that I can not hear any audio when call from 'sip or H323 phone' and configure something like: exten => _01XXXXXXX,1,Playback(thank-you-for-calling|noanswer) ... It works if I remove the 'noanswer' parameter but in this case it connects

# Span 1 span=1,1,0,esf,b8zs bchan=1-23 dchan=24 echocanceller=mg2,1-23 # Span 2 span=2,2,0,esf,b8zs bchan=25-47 dchan=48 echocanceller=mg2,25-47 # Span 3 span=3,3,0,esf,b8zs bchan=49-71 dchan=72 echocanceller=mg2,49-71 # Span 4 span=4,4,0,esf,b8zs bchan=73-95 dchan=96 echocanceller=mg2,73-95 # Global loadzone = us defaultzone = us Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1"

Hi all I have installed AAH 2.2 in my P4 PC following AAH handbook PDF and http://mundy.org/blog/index.php?p=62#amp and made as per the guide says and downloaded SJ Phone, and registered user and when i try to dial the 19197543700 i get message that, all circuits are busy now, please try your call later and when i see in the console i get this mesage any help Called easycall/19197543700

Hello, I have an issue with Digium TDM 400 card series. When I try to make outgoing call (PSTN call) for example, the Zap channel could not be created and busy channel message appeared. Below is the full log : [Feb 5 09:26:17] VERBOSE[3047] logger.c: -- Executing [s at macro- dialout-trunk:20] Dial("SIP/213-09648720", "ZAP/g1/08170709XXX|300|") in new stack [Feb

Hi, I am having problems with an Asterisk with a Digium TE205P card. The issue is that the Ring Back Tone is noisy. I am making modem's calls and this noise influences on the initial negotiation protocol, so modems have to recall. My configuration is: Asterisk version: Asterisk 1.4.21.2 Linux version: CentOS release 5.2 (Final) Card: Digium TE205P

Dear all i have a TE205P connected to an Asterisk 1.2.18. Yes i know, the version is old but since now the system was stable and i don't have the necessity of an upgrade. The system provide an IVR service that: 1) receive the call 2) verify the queue length 3) hangup if queue length is > 1 4) put the call in the queue othervise Then, there is an AGI php script that 1) verify the queue

Dear all i'm trying to originate an outgoing call with the command originate, from Asterisk's CLI i'm typing: CLI> originate IAX2/my-iax-provider/number2call application wait 10 [Apr 18 19:31:12] DEBUG[32331]: chan_iax2.c:4000 create_addr: prepending 40 to prefs -- Call accepted by 62.149.202.150 (format ilbc) -- Format for call is ilbc -- Hungup

Hi, I'm running Asterisk SVN-trunk-r226890 and whenever I restart asterisk and try to make a call I get the following error message: ======================================================================================== -- Executing [6781948 at default:1] Dial("IAX2/iaxy-7477", "DAHDI/g1/96781948") in new stack [Apr 25 13:00:10] WARNING[3772]: app_dial.c:1806

hi i'm trying to configure a TE205P on asterisk@home i've edited /etc/sysconfig/zaptel adding this line: MODULES="$MODULES wct2xxp" now, when the system is loading, i can see that the wct2xxp module is loaded correctly but if i try the command: /usr/local/sbin/genzaptelconf i get: STOPPING ASTERISK STOPPING FOP SERVER Generating '/etc/zaptel.conf' Generating

I read the wiki and looked at the examples, but I'm still having problems. I have a Digium 4 port card with POTS lines plugged into all four ports. How do I play the congestion tone the the caller when they try and dial out but all the lines are in use? should something like this work? [dial-trunklocal] ; Local calls ignorepat => 9 exten => _9NXXXXXX,1,Dial(${TRUNK1}/${EXTEN:1}) exten