similar to: problem with outgoing calls Unable to createchannel of type 'ZAP' (cause 34 - Circuit/channel congestion)

hi i've configured a TE205P on asterisk at home this is my zaptel.conf span=1,0,0,ccs,hdb3,crc4,yellow span=2,0,0,ccs,hdb3,crc4,yellow bchan = 1-15, 17-31 dchan = 16 bchan = 32-46,48-62 dchan = 47 loadzone = it defaultzone = it and my zapata.conf signalling=pri_cpe ; pri_cpe = PRI slave ; pri_net = PRI master switchtype=national usecallerid=yes hidecallerid=no callwaiting=yes

I setup my aah box with a sip trunk at irisxa.iristel.net Incaming it is ok but when I try to dial 8 and the nr where I want to call I get all line is busy. In my log I have these: Feb 22 14:33:04 DEBUG[3156] manager.c: Manager received command 'Command' Feb 22 14:33:04 DEBUG[3156] manager.c: Manager received command 'Command' Feb 22 14:33:19 VERBOSE[2721] logger.c: --

Hello, I have a TDM400 and currently have 2 of the ZAP Trunks configured on it. Zap/1-1 and Zap/2-1. I am Running Asterisk@home Version 2.4 with AMP version 1.10.010 In my Outbound Routing I have the Trunk Sequence set up so that 0 is Zap/1-1 and 1 is ZAP/2-1 What I see is that when Trunk Sequence 0 is full, it does not open Trunk Sequence 1. I have found that this is true even if I

Hi, I use: Trixbox-2.2.4 FreePBX-2.3.1.0 Asterisk-1.2.17 BRIstuffed-0.3.0-PRE-1y-e Zaptel-1.2.19 ..with two ISDN cards, often but occasionally the dial out failed but is possible to receive external call. My zapata.conf conf is: [trunkgroups] [channels] language=it context=from-pstn signalling=bri_cpe_ptmp rxwink=300 pridialplan=unknown prilocaldialplan=local switchtype=euroisdn

Hi, sorry for the long debug output below. I configured Asterisk with AMP to send the whole number including the extensions of the callers to the called party. Whatever I configure in AMP it looks like it is used, In my eyes it is ok, but doesn't seem to work. 033811234451 is the call id i configured, and it seems to use them, but the caller will only see a 0338189040 instead of my

Hi Folks, I'm have Asterisk version 1.2.1 with a A101 PRI card. I'm working with the CLEC to bring up the PRI and inbound calls are hanging up at his end after a few seconds. I ran PRI debug but it only gives me minimal insight. " Ext: 1 Cause: Unknown (16), class = Normal Event (1)" He ran a trace and the only difference he is seeing is a "ISDN interface explicitly

Dear All, I have an asterisk server version 1.2.12.1 along with trixbox and I am having this nasty problem, I have a TE200P and have an E1 pri attached to it and zttool says it's OK, I have configured the whole 31 channels into one group as follow: Zapata-auto.conf: callerid=asreceived signalling=pri_cpe switchtype=euroisdn context=from-zaptel group=0 channel=>1-15,17-31

I have an analogue trunk to an AT&T Definity. It has a DISA context defined. From a Definity handset call the analogue port extension 1008 and wait for dial tone from asterisk. It takes between 3&4 rings. Likewise from Asterisk SIP handset <PBX Access No><PBX Extn> takes nearly 10 secs to ring. Is this configurable? Ian Cowley -----Original Message----- From:

Skipped content of type multipart/alternative-------------- next part -------------- asterisk1*CLI> soft hangup Zap/1-1 Requested Hangup on channel 'Zap/1-1' == Spawn extension (macro-exten-vm, s-BUSY, 2) exited non-zero on 'Zap/1-1' in macro 'exten-vm' == Spawn extension (ext-local, 220, 1) exited non-zero on 'Zap/1-1' -- Hungup 'Zap/1-1' --

Hello, I have setup a test server with asterisk/AMP and have several 7960's connected to it. The asterisk server has a public ip and all the 7960's are behind nat'd routers. When I try to call from extension to extension I get directed straight to voicemail. I do not have any cards installed and instead direct everything to an Ondo server. I have been told it's not an AMP

Hello everybody, and first of all sorry for my poor English. I'm having trouble with Quadbri installed on Asterisk 1.2.17-BRIstuffed-0.3.0-PRE-1y-e. Everything is working fine, except calling to switched off or "out of coverage" cell phones. In this case I have to wait 40 seconds until Asterisk tell me that "all circuits are busy now" instead of receive cell phone

I just had a user report that they called out to someone on a cell phone this morning, and after a short conversation, the call was dropped/lost. The person on the cell phone says that this is very rare, and would not suspect the dropped/lost call to be on their side. I have looked at the asterisk/full log as thoroughly as I can, and have pasted the lines which seem relevant to that call below.

I've a call center using IAX softphones provided by a third party. We've observed problems where the IAX phones seem unable to use our PRI trunks. A sample anonymized call is provided below with the PRI debug calls embedded. Any thoughts, comments or suggestions would be welcome. In anonymizing it, I preseved the format and number of digits sent. -- Accepting AUTHENTICATED

Have asterisk@home 1.2.1 The server is on an internal network eg 10.10.10.10 It is NAT'd 1:1 via Checkpoint firewall to external public IP eg 50.50.50.50 The remote IAX2 phone (ATCOM320) is configured to call 50.50.50.50 on extension 1055. Outbound calls to 1055 work perfectly. Inbound calls from 1055 get picked up as if it were an external call (see below) and goes straight to the ring

Hi All, I have searched the various post and not able to find the solution. I am using Asterisk 1.4.21.2 for outgoing calls. Earlier i used ZAP trunk and it works fine. Now i need to move to SIP trunk and configured the same. When i try from softphone i got error as "Call rejected" and in the asterisk i got error as

I have call center PCs that switch between an IBEAM SIP softphone and a NEBU IAX softphone (for reasons that aren't germane here). The SIP softphones work fine, but the IAX softphones get a fast busy unless I give them an IAX trunk to use, instead of the PRI trunks that all the other phones are using. I am using Asterisk 1.2.3. svn rev 47264. I've appended a sample call trace. The

i have a prablom here, i want to send a call from A to B use sip trunk , the call can sended B,but not work to PSTN. the message from B server. help pls,what's rong? > > <--- SIP read from 192.168.0.176:5060 ---> > INVITE sip:15921256331 at 192.168.0.151 <sip%3A15921256331 at 192.168.0.151>SIP/2.0 > Via: SIP/2.0/UDP 192.168.0.176:5060;branch=z9hG4bK51a51b96;rport

hi,all when i send a call to other server use SIP trunk, i got this below, <--- SIP read from 222.46.18.52:5060 ---> SIP/2.0 403 Forbidden what's rong with is? > Asterisk 1.4.21.2, Copyright (C) 1999 - 2008 Digium, Inc. and others. > Created by Mark Spencer <markster at digium.com> > Asterisk comes with ABSOLUTELY NO WARRANTY; type 'core show warranty' for

Hello, Sometimes the call gets answered for 1 second, but actually the phone has not rang, it?s just the CDR, and asterisk hangup automatically, I cought the log of 1 call like this, I hope you can help me with this. My setup is : <vendor> ----SIP--? <Asterisk> ?----IAX2---? <Asterisk with Dhadi channels> Here: -- Executing [966505103150 at from-internal:1]

I have a problem calling a certain number from our PRI line. Calling the number from a separate PSTN phone works fine. The remote number seems to have some funny call redivert setup, when you call it, it answers immediately, makes some kind of beep and then starts to ring. Our PRI is in the UK from Telewest/NTL/Virgin Media and most outgoing calls work without a problem. The server is