similar to: TDM2400P FXS Only vs. T1/E1 to FXS Channel Banks

hi, we are currently planning are large site which will migrate from an old siemens hicom pbx to asterisk. it will be a slow migration, the asterisk server will be inserted between the telco E1 and the hicom. new phones will be sip ones. the customer has several fax machines and analog phones (some of them have to be explosion-proof). around 50 analog ports in total are needed. as we are in

Sorry for the cross-post, but this could be either lists problem. I have 2 boxes running 7-STABLE as of 20081130, both i386 SMP. One is running ISC DHCPD 3.0.x from recent ports, and the other dhclient from make world. The server is refusing to answer the DISCOVER request, as it thinks the IP checksum is wrong, which tcpdump also confirms. Other DHCP clients are working fine on this network,

Hi, I'd like to change 3 TDM400p with one TDM2400p to avoid echo (my intention is to use a TDM2400P echo cancel module). It TDM2400p working good with asterisk 1.2.1? Or I need to install a new asterisk version? TIA Giorgio Incantalupo

Hi i have a tdm2400p and installed asterisk 1.4.11 with zaptel 1.4.5 im having an error message when in running asterisk with the tdm card in. here's the error from the console of asterisk: [Nov 18 10:30:44] ERROR[5557]: chan_zap.c:7489 mkintf: Unable to get span status: Inappropriate ioctl for device [Nov 18 10:30:44] ERROR[5557]: chan_zap.c:10466 build_channels: Unable to register channel

The HP DL380 G5 (like many rack servers) has no AMP Mate-n-Lok connector available to attach to a card that needs more power than the PCI bus can provide, like the TDM400P when FXS modules are used. HP has confirmed that there is no part they sell to give you such a connector, and Digium says their business edition folks got it to work, but only by doing nasty warranty-voiding things to the

For example, how much power would a server with 3 of the TDM2400P fully loaded cards draw? We're trying to figure out what APC power we should have to achieve approx 30 minutes back-up time. Would appreciate any learnings or methods on calculating the power draw and determining the appropriate back-up device. Thank you. Melisa.

I am having issues with a TDM2400P. It appears when the ZAP channel dials out, it randomly chops the first digit off of the number. I have tried relaxdtmf=yes, turning up and down the txgain, turned off and on the echo cancellation, generated new zaptel (with updated spinlock.h)... I am at a loss. Can someone please offer some help? Thanks. TJ

Hi list, I have this problem: when someone is making a call, with asterisk and a TDM2400P connected to 8 fxo lines, the sound is good, but if three, for people are calling at the same time the sound got worse and worse. Using other voip cards the sound is much better even with all user calling at the same time. What can be, the problem? Someone else has having the same

Hi, I have a problem with TDM2400P card. The card is detected ok, I can make a call but only with pulse dialing (not tone dialing) without hear sounds from the headset. When I receive a call, I can to establish a communication, but without hear sounds from the headset. When I dial any phone key, I can hear dtmf tone. I'm using Elastix 1.5.2. These are my configuration files:

A big G'day to everybody on the Asterisk list. I am having a lot of trouble getting the TDM2400P card working in asterisk. I will give the important details below, please let me know if I am doing anything obvious or ideas for debugging this. SUMMARY: I get the right voltages on the line with the phone on or off the hook, but no dial tone, no ringing in or ringing out. INSTALLATION AND

Hello, Thank you for your support of Digium and Asterisk. Yesterday, we identified a problem with the driver for the TDM2400P card when used with FXO port modules. The X400M was producing (and expecting) the audio signal at an abnormally high level, which negatively impacted the performance of the echo cancelers, both hardware and software. It also resulted in unusual audio artifacts when the

Hi, I cannot make my TDM2400P (with Echo Canceller module) detect faxes. I tried with a TDM400P and it worked at 80% (20% of faxes were lost). My test conf.files are: _zapata.conf_: context = inbound faxdetect = incoming language = it musiconhold = default signalling = fxs_ks callerid = "call_or_fax" channel => 1 extensions.conf: [inbound] exten => s,1,Answer exten =>

Hi All, I have the problem with TDM2414E card (16FXO & 4 FXS with echo cancellation). I have already connected to the asterisk server and loaded wctdm24xxp module. When I connect the phone to FXS port, It gets the dial tone but I cannot dial to any number (I can press the phone button but nothing happens even the busy tone). There is no activity in the asterisk CLI. It just prints

Do the zaptel drivers need to be told >NOT< to use the software echo canceller when using a TDM2400p card with hardware echo canceller, or does the driver figure this out by itself? Thanks, Andrew -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061117/7dc52295/attachment.htm

Hello, We've purchased a 2nd Wildcard TDM2400P for our asterisk server. I've looked around but I can't find documentation on how to properly setup 2 or more telephony boards in asterisk. In particular, I want to ensure that the boards are assigned the same device channels on boot (for example, if you have two NICs in a Linux box and you want to make sure one card is always eth0

Hi, I have a box with Debian Sarge, Asterisk 1.2.1 (and zaptel 1.2.1) and a TDM2400P with echo canceller. I installed the card but no echo cancellation is being made...seems like the echo canceller module does not work, infact the software cancellation is working. My zapata.conf has echocancel = 128 and echocancelwhenbridged = yes but no echotraining parameter which gives a warning. I found

Hi Francois, Thank you for your interest. I tried the card alone so I don't think is an IRQ problem (anyway is there a way to be sure?) To be sincere, in all systems I saw (even working ones) there is an IRQ balance failed where Linux boots. The system is new, I tried different processors (P4 and Celeron) with SMP kernel and without. The card has the echo module, could not be

Hi. I am using Digium TDM2400PFXO with Asterisk1.6. When call sets in the box , it answers the call even the phone is not picked. ideally it should answer the call when the phone is picked up. Its charging the clients. Please let me know how can I cover this ? Thanks in advance. -------------- next part -------------- An HTML attachment was scrubbed... URL:

We just bougth a tdm2400p with all the modules for FXO, but we are having some troubles with the card, cause it aparently is stripping some digits from the dialed number, we tested the same server with a tdm400 and everything worked as expected. We?ve already added "w" before the dialed number with no results, is there any way to solve, is it a bug thanks

Ok, the Zhone sucks and the Adtran 750/850 seems to be a little too expensive. Can anyone recommend a decent channelbank that won't break the bank? TIA, -- Troy Settle Pulaski Networks http://www.psknet.com 540.994.4254 ~ 866.477.5638 Pulaski Chamber 2002 Small Business Of The Year