similar to: FastTrak TX200 driver

Hello, In some weeks I'm going to reinstall some old RedHat9 based servers with Promise FastTrak TX2000 "semi-hardware" RAID1 controllers. I just tried to install CentOS 4.0 on a computer with a spare card and as usual both HDD attached to the RAID1 controller are seen separately by the installer because the specific driver for the TX2000 wasn't loaded. Nothing new here, it

Trying to install FastTrak TX2000 in box with CentOS 3.3 (kernal 2.4.21-20.EL.c0) install. Just downloaded Redhat 8/9 driver from Promise. But "sh install" says correct driver not found on diskette. Any suggestions? Thaks -------------- next part -------------- An HTML attachment was scrubbed... URL:

What kind of implementation software or hardware is recommended for ide Raid 1 with ext3? Some controllers from Promise like their new FastTrak TX2000 look nice. But won't I be tied into the kernel version that is only supported under their drivers? Is ide software Raid stable and fast with ext3 for a production system? Thanks in advance. Aaron Lopez

Look for consultant (for fee is acceptable) to provide step-by-step setup of DNS (forward & reverse) through the graphical interface of CentOS. Current setup is qmail server on static ip being nat''d through router. Need to setup for full DNS including PTR. Please contact - Beth Curotto American Business Networking, Inc 800-818-3244 -------------- next part -------------- An HTML

Does anyone have this card working in hardware RAID mode? I can see the individual ATA drivers when booting. The promise site has drivers for Redhat 7.3,8 and 9, but nothing for higher. I see the source code, and can build the module, but I need it loaded at boot time. Any help would be appreciated. Thanks. Sean

Hi everybody, I need to setup a couple of new servers with RAID 1 & another with RAID 5, witch card will have built in support (no need for drivers). It can be for ATA or SATA drives (any preference on ATA or SATA ?). I'm looking for a PCI card , or a motherboard with built in card. I been looking at the : 1. "3ware 64-bit PCI to SATA RAID Controller Card, Model "Escalade

anyone have experiences installing SATA raid card with CentOS/RHEL? I am considering Promise FastTrak S150 Tx2 plus, FastTrack 2200 or FastTrack S150 Sx4 Which one of these ( or any othe brand) can ensure smooth install of CentOS without problems, thanks. :)Harris LIU

What is really puzzling me is that the ataraid device (/dev/ataraid/d0p1 mounted as /bigdisk) 2x 123GB IBM Deskstar's is formated as ext2...top and ps etc... show a fight between kjournald and kupdated and all searches for kjournald or kupdated fights suggest ext3 issues... :-) It's a RedHat 7.2, 2.4.7-10 custom kernal (I added in the Promise FastTrak support and HIGH mem support to

Beth, I can get to http://66.196.225.55/, but if I try going to the mail subdirectory I get: Forbidden You don't have permission to access /mail/ on this server. This seems to be a web server, but your question says vsftpd. I recently set up an ftp server using vsftpd. I found that for a directory to be accessible to anyone, permissions must be set so that the directory is executable by

I have just set up a box - HOSTNAME mail.abni.com It has Qmail setup. I also want this box to serve as the host for our website - abni.com Can someone point me in the direction of where to go next. I am unsure if HOSTNAME will be a problem as a web server. Currently I have loaded a html doc in - /var/www/html, but I had to load from cd directly on this machine. Is is neccessary to setup ftp

Hi, One of my CentOS 4 server is a repository for backups for other machines. In this server, there is a 3ware RAID card and 2 HDD for the OS + data of this server. I also have 2 drawers (each containing one 200GB hdd), connected to a promise TX2000 card. One disk will remain in the server and one will be taken outside. What would be the best strategy for syncing the hdd when I swap

I have a North American BRI configured as National ISDN (NI-1) on an SBC (Nortel?) switch. SBC calls this "FastTrak ISDN", and it's surprisingly inexpensive -- less than two POTS lines. I've been trying to find an inexpensive PCI interface solution to connect this to Asterisk as voice lines. I prefer ISDN BRI over POTS lines because of the improved signalling, fast dialing,

Hi Everyone, Has anyone had any experience of using the Promise FastTrak SX4000 or SuperTrak SX6000 IDE RAID Controllers under Centos (if it matters I'm using version 4). I've seen it listed on linuxcompatible.org as working but would prefer to find out any first-hand experince before I buy. I'm looking to build a new mini server based on Mini-ITX and have found a great 1U case

Ulrik wrote: Message: 2 Date: Thu, 23 Sep 2004 14:59:14 +0200 (CEST) From: "Ulrik S. Kofod" <usk at cybersite.dk> To: centos at caosity.org Reply-To: usk at cybersite.dk Subject: [Centos] network card / kudzu When I have installed centOS, Kudzu says my network cards have been removed, and right after it finds them again and asks me to configure them? It looks like it is the

Can someone point me to the http:// location where I can import the key for 3.4 i386 Beth -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.caosity.org/pipermail/centos/attachments/20050228/02319731/attachment.htm

Hello. I would like to know if promise RAID cards are compatible with CentOS / RHEL ? I have seen that only SATA is supported on the RHEL hardware compatibility list. The other ATA raid cards seems not to be compatible. They give source code and promise grants compatibility with RedHat 8 and 9 but not RHEL. I would like to know if somebody tried a ATA raid card like Fasttrack TX2000, SX4000,

System = CentOS / Apache 2.0 / HTML files location = /var/www/html Nat'd IP - ports 80, 20, 21 already opened & routed to internal ip. I desperately need the quick & dirty solution. I need a setup where one user can ftp from another desktop (windows) to upload new website files. I currently have CuteFTP, but will use anything needed at this point. I need to try to test this today.

Greetings - I'm looking to put some cheap storage into my server, which is running centos 3. I'm looking at the Maxtor SATA/150 PCI Card and a big maxtor sata drive. I would like to make sure that CentOS has driver for this controller. I looked in Red Hat's hardware database and did some google'ing but I couldn't find any info to confirm that this card is compatible.

http://bugs.freedesktop.org/show_bug.cgi?id=26568 Summary: Xv Corruption and X Lockup w/ Nouveau on C51 (Geforce 6150 Go) Product: xorg Version: 7.5 Platform: x86-64 (AMD64) OS/Version: Linux (All) Status: NEW Severity: normal Priority: medium Component: Driver/nouveau

Is there a novice level way to produce a distro/copy/whatever of an installation so that I can duplicate it on a new box? Is there a hard drive copy application that can copy linux drives? Beth -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.centos.org/pipermail/centos/attachments/20040915/6769295d/attachment-0003.html>