similar to: Handset phone to replace Flash Operator Pane l

Hi All I am having a problem setting the outbound callerid number on a PRI E1 in South Africa. The outbound number keeps on appearing as the main PRI number. How does it work between Asterisk and the Telko? More importantly how do I get it working? Kind Regards Garth -- Garth van Sittert BSc (Physics & Computer Science) ----------------- Mobile: +27 (0)83 791 6662 Email:

Hi All Has anyone come across a handset that can somehow replace FOP? Some users don't like FOP unless it is on a dedicated PC. Thanks Garth

How do you set the CallerID? Have you checked with your provider that they've enabled callerid? If yes, are you using a correct number that the provider allows? Regards, Jan -----Ursprungligt meddelande----- Fr?n: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] F?r Garth van Sittert Skickat: den 2 februari 2006 12:37 Till: Asterisk Users Mailing

Hi All I have noticed that when calling over mISDN channels the call itself is made over the channels listed in misdn.conf eg: 1,2,3,4 as misdn/1, misdn/2, misdn/3, misdn/4 etc. However, when looking through the CDR's the call gets logged as misdn/0, misdn/1, misdn/2, misdn/3, misdn/4, misdn/5 etc. I also noted that busy, failed, congested calls link mainly to misdn/0. The only logic I

Anybody tried one with Asterisk yet ? Views ? Best Regards, -- This message has been scanned for viruses and dangerous content and is believed to be clean. SplatNIX IT Services :: Innovation through collaboration

Hi All Does anyone know how to use the MySQL cmd in Asterisk with LIKE and % in the query? I have: exten => s,5,Set(query=SELECT name from contacts where tel like %${number}) exten => s,6,MySQL(Connect connid hostname username password dbname) exten => s,7,MySQL(Query resultid ${connid} ${query}) But there seems to be a problem with the % sign and I don't know how to

Hi, I am trying to send "404 Not found" reply, without any luck with the following: exten => 555,1,Playback(you-dialed-wrong-number,noanswer) exten => 555,n,Playback(check-number-dial-again,noanswer) exten => 555,n,Congestion() However the above results in "500 Service Unavailable" being send out. What would be the correct application/function to generate "404

Hi All Does anyone have any ideas around what processing power is needed when bridging PRI channels and recording? I am not sure how the bridging takes place with and without recording? I basically have a situation like this: Telko <----> Asterisk <-----> Legacy PBX Where the lines are PRI's between Telko and Asterisk and Asterisk and the Legacy PBX. At what level does

Hi All Has anyone experienced a crash specific to asterisk 1.2 and Centos 5 when using the misdn hfcpci module that comes with zaptel? I have an asterisk pack based on asterisk-1.2.17 that I have been using on dozens of machines that are rock solid and stable. Today when I tried moving it to Centos 5 I experienced a complete OS crash when calling over HFC misdn channels. Didn't really

Hello everyone, this is my first post to the list, so hello again. We're a small company in Romania and we're trying to set up a really small version of "call center". That is, we want to get a few land-lines from our telco in different countys and "bridge" all calls to our HQ, in order to make it cheeper for our clients to call us. Unfortunatelly there's no ISP

In the list I found some messages that *8 doesn't work so well. Is there any possibility to create a extention that you can call, and if you are fast enough, pick up a number? (Also if you are outside your callgroup) like pseudo code: exten => 888, 1, EnterPhoneNumber() exten => 888, 2, EnterPass() exten => 888, 3, TransferCallToThisPhone() exten => 888, 103, Invalid()

Hi list! Does anyone have experiences with the updated model of the Kirk IP600? The V3 model is supposed to support SIP instead of only SCCP or H323 which would make the use with Asterisk a lot easier. I have only tested the Kirk IP600 V2 with SCCP / Skinny protocol which is still giving me severe headaches : - the standard Skinny driver in * doesn't work, only the version of Sergio

Hello, I had had some echo issues. I purchased a digium echo canceling card, and the echo issue seems to be reduced but not eliminated as I hoped it would be. I currently have it set to 128 'yes'. I've tried 256, but when I try 256 what happens is that instead of getting better echo canceling I get AWEFUL echo. Can anyone enlighten me? I am running 1.2.6 with a 4 port PRI card.

I am trying to set up a linux based faxing solution for a client, and have found that the modem they have (ancient dataplex external unit) just isn't up to the job. It talks to some remote fax machines but not others. A new external modem ranges from AUD$75 to AUD$400, which got me thinking of other possibilities... #1 FXO PCI card (more expensive for 1 port, probably cheaper for 2+) #2

As the subject line says: Is PING a good indicator of network latency? If not, how can I measure latency? Thanks, Cosmin Prund

Hi all, I'm getting some noise gate like effects on our sip lines & I think I need to disable silence supression, I'm searching docs & not finding where this can be set, does * have a setting to turn this off? basically what's happening is when we stop talking, the other end hears total silence, but when we talk, they can hear the background noise in the office, this sounds odd

Sip to sip calls are fine, both local on Asterisk and over a SIP gateway, however some people who call on the PSTN line say we are very queit and vice versa, can the volume be turned up on the PSTN line? The volume buttons on the VoIP phones only turns up the others voice, so this is a fix for us, but how do I make our voices louder for the people on the PSTN line? Thanks. Paul.

Hi, I have 2 g729 licences - what I want to do is use g729 by default but if I get more than 2 calls at a time, use gsm for the others. So, I put this on all my sip providers: disallow=all allow=g729 allow=gsm However, this just seems to use gsm for everything. If I comment out the gsm line, it then uses g729. I thought it would use the codec's in the order they are allowed - is this

-----Mensaje original----- De: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com]En nombre de asterisk-users-request@lists.digium.com Enviado el: jueves, 02 de febrero de 2006 10:15 Para: asterisk-users@lists.digium.com Asunto: Asterisk-Users Digest, Vol 19, Issue 15 Send Asterisk-Users mailing list submissions to asterisk-users@lists.digium.com To

Hi All Does anyone know how the hints in asterisk works? How does a SIP phone interact with the hints? I am having a problem with certain phone models that do not set the hints correctly when I list the hints with a 'show hints'. Thanks Garth