similar to: PRI to PRI not passing callerid

So I reached the point where my PRI is accepting incoming calls, but I cannot dialout. I must be doing something stupid, but I can't figure it out. The Asterisk box is sitting between the Mitel and the phone company, and has PRI lines to each. Asterisk was built from CVS r1-0 Log for a call from mitel heading outbound: ------------------------- -- Accepting call from '' to

I have a user who's system crashes on pri hangup request. Tried 1.4.19.1 and 1.4.20 as well as the latest libpri no change Progress is as follows...... < Supervisory frame: < SAPI: 00 C/R: 0 EA: 0 < TEI: 000 EA: 1 < Zero: 0 S: 0 01: 1 [ RR (receive ready) ] < N(R): 025 P/F: 1 < 0 bytes of data -- ACKing all packets from 24 to (but not including) 25 -- Since

It seems consistant after dialing dozens of times that the call that doesn't go through is the one the gets the log message "No echocancellation requested" (chan_zap.c) and the "Scheduleing timer" (channel.c) in the middle of receiving the DTMF tones. I'm now using the T400P card last week very simular problems the the T100P (although I think I was actually loosing

I've got a new setup (different building) where Asterisk is sitting between the PBX and phone company on a E&M T1 line. Mitel PBX <-> Asterisk <-> Phone company Inbound works. Asterisk gets the in-band digits from the phone company and hands the call off to the Mitel just fine. Outbound is weird. Asterisk seems to expect that the mitel will send routing information

Hi all, I must admit that I am stuck. I have a TDM400P card with two FXS and two FXO modules which I had set up and configured so that it was working beautifully. The only problem was that occasionally it would get itself into a state where outgoing calls would simply be met with a very loud static. A reboot would fix this issue and everything would work fine for a while. Recently however,

Well, my faxes passes through asterisk successfully, however I still have some problems about fax reception by rxfax. The softfax answers, and negotiates transmission, however then as some stage of communiation something is wrong. But I have nothing more but this log: Jun 2 00:10:21 DEBUG[16900]: chan_zap.c:4242 zt_read: DTMF digit: * on Zap/10-1 Jun 2 00:10:22 DEBUG[16900]: chan_zap.c:4242

Hi, I'm having problems using a TDM400P Card. I put my SIM card in a Nokia Premicell and connected it to a TDM400P card but when I make calls to the number, it hangs up automatically. The card also can't call out. Any ideas? I've searched the archives without much success. I appreciate all your help. Details: I'm using Asterisk 1.2.17 on Fedora Core release 5 (Bordeaux). On an

Hi all, I've been running Asterisk with a TDM400P for about 6months, no problems. 2 in/outgoing analog lines, one analog phone. Recently I was messing with the XTEN client, got to finagling with things, and not knowing what was wrong I upgraded from 1.0.7 to 1.0.9 (both asterisk + zaptel). I was testing various things, and found everything worked except outgoing calls. So I checked

Hi all, I tried to connect the bristuffed(0.3.0-PRE-1i) * to an Alcatel PBX via BRI (zaphfc) and Q.SIG. The Alcatel PBX is connected to the outside world and should forward our calls to the telco. This setup works correctly as far as I use euroisdn as the switchtype. The first problem was that it is only possible to run the * side in CPE-mode -- I wanted NET. Anyway, I configured * this way:

Hello I have an interesting situaltion and not sure if I am doing something wrong or it is a BUG. I Installed Rhino Channel on T1 line and connected Analog Phone on Rhino's Zap Channels. If i pickup analog phone and hangup without dialing any number , I am getting extra ring after hangup and if i dial any digit than there is no ring on Analog phone after hangup. Log's looks like this

Hi! For demonstration purposes I try to bridge an incoming video call from a 3G mobile handset to another 3G mobile handset using asterisk as "switch". On the incoming call leg I see all expected bearer capabilities (Digital, 64k Transparent, G.7xx 384k video) but on the outgoing call leg the bearer capability G.7xx 384k video get lost and therefore the call is dropped from the mobile

Hi Guys, I am calling out 416-999-1111 on Channel 1 of PRI and then calling 416-999-2222 on Channel 2 of PRI. When the two channels are going to be ZAP native bridged, both channels hangup and CLI show PRI cause (16). Asterisk Verbose *(Channel 1 already connected to party)*: -- Requested transfer capability: 0x00 - SPEECH -- Called g0/4169992222 -- Zap/2-1 is proceeding passing it

Hi Guys, Full PRI installed in Canada with Sangoma A101DE and Asterisk 1.4.21.2, LibPRI 1.4.10. Placing a call into PRI and then transfering that call out to another number. Problem is that the call rings out but the moment the other party pickups both legs of the call are disconnected give Cause code 16.

Hi list, I'm getting an error on a E1 link to the telco, after some weeks of operation without trouble. I have an asterisk with a TE405 in passtrough mode: two E1 are connected to the Telco, two E1 are connected to 2 Siemens PaBX. Only 15 channels are used on each E1 (conf is attached).The system has been in production for nearly a year, and does work flawlessly for weeks, then I

I have a T1 link from asterisk 1.2.23 (also tried with 1.4.13) to a Meridian Option 61C. Calls either way drop with error "Channel 0/23, span 1 got hangup, cause 100". Can anyone offer insight into the cause and solution/workaround? (I tried upgrading to Ast 1.4.13, and upgrading matching zaptel & libpri, put the problem is identical). For testing, I tried a call from the

PRI debug of the entire call would be great, also, switchtype would be awesome as well. Thanks! Matthew Fredrickson On Thu, Mar 24, 2016 at 4:07 PM, Carlos Rojas <crt.rojas at gmail.com> wrote: > Hi > > Did you activate the pri debug on the cli asterisk? > > On Thu, Mar 24, 2016 at 12:59 PM, Carlos Chavez <cursor at telecomabmex.com> > wrote: >> >>

Hi! Has anybody seen anything like this using zaphfc? On outgoing calls (via isdn) , the line gets hung-up as soon as the called party answers. As seen below i get some protocol error (6) - but i'm not sure if this is related to the "hang-up" which apparently comes a little earlier?! Incomming calls on the isdn (zaphfc) interface is working just fine (P.S. what about the

Hello All, I'm having problems connecting Asterisk to Telco in Poland (using E1). The telco guys are saying that the RING message is missing. How can I make Asterisk to send the RING message? Does anyone have any samples of zaptel and zapata for Poland? Best Regards, Alex ____________________________________________________________________________________ Do you Yahoo!? Everyone is

Hi, I have a problem with dialling internationals numbers, and I don't now what is the cause. I have one asterisk with a e100p card connected to the Telco (spain/telefonica) and it can dial local and national numbers without problems but when I try to dial a international number it hangs-up. I call the Telco to ask if the E1 can do international calls and it said that it can. I have tried

Hello all, I have Asterisk 1.2.1 and a TE110P connected to a Nortel Meridian Option 81C system. The PRI line is currently setup as DMS100. Here are the relevant lines from zaptel.conf and zapata.conf: zaptel.conf: span=1,1,0,esf,b8zs bchan=1-23 dchan=24 loadzone = us defaultzone = us zapata.conf: [channels] language=en context=from-internal musiconhold=default switchtype=dms100