similar to: RE: X100P help required

Hi, I've got the latest asterisk@home setup running with SIP. I've been trying to tie it in with the PSTN off and on for a while with no success. I gave up on ISDN and purchased 2 x100p cards from x100p.com. I've got the card installed, the machine can see it. The problems I have at the moment are First time I start up the drivers and asterisk, I can call the pstn number. The

Does anyone know if there is a zapata.conf option to tell * to listen for a dialtone before dialing? I've got a couple of analog phones on a pstn line shared with a x100p * fx line. If someone is on the analog phone and another person initiates a call through * to use the same line, * dials over the top of the existing conversation. Is there a way to have * detect dialtone before dialing?

Hi all, I am either going daft or not reading things right. I have just installed, (well 10 hours ago) a TDM40B and 3 X100P cards. I have followed the examples for the conf files to the letter. I can call the pots extensions OK from IAX clients, SIP clients and from the incoming X100P cards. But, if I pick up the handset to make a call all I get is the engaged tone and the following message.

I'm looking to get an x100p off ebay and am not particularly familar with the "life cycle" of the card.. An "Authentic X100P" listing has a buy it now of $29.95 and says There are 3 types of cards Asterisk would recognize: *Screenshots from the official, original driver install Cheap "OEM X100P","Clones", "Compatibles", Knock-Offs

Hi I thought this might be of general interest. Recently I purchased an X100P from a Digium reseller in the UK. Very pleased with the card; works perfectly. My friend (known for his deep pockets and short arms) purchased an X100P card from Ebay. He's had no end of problems with line noise, dropped called etc so I thought I would compare the two cards. Plus mine was delivered within two

Hi All... I have installed a single X100P card in my PC and am playing with Asterisk. The wire I plugged into the X100P has two POTS lines on it, wired on the RJ45 in the normal way. I am getting odd behavior. It seems when I dial out that the X100P dials both lines at the same time. I have two questions. First, I see that the X100P is only a single channel. Does this mean that I can

Hi all. I`ve installed a X100P on my box and is working well with incoming and outgoing calls as a trunk with one PTSN line. I want to connect the X100P to my Panasonic 616 EASA-PHONE as an internal extension to permit to users to make calls to SIP devices from analog phones, the problem is when I dial the ext number where the X100P is connected I get busy tone. What config I need to change to

Hello my brothers and sisters, Is "X100P" card suitable to VoIP? and if "yes", am i need to only "X100P" and "Asterisk" Package? or i need also to other cards or packages? and if "X100P" card not suitable to VoIP, please recommend a another card, (please take in your account that i would like to connect standard analog line to the card

Hello, Can the wildcard x100P be bought of the shelf in stores - say in Singapore. Thanks Varun

Hello, I have X100P card but exten => _9X.,1,Dial(Zap/1/${EXTEN:1}) does not work. The error is app_dial.c:803 dial_exec: Unable to create channel of type 'Zap' (cause 0) Zap show channel, lspci etc show everything is normal. Because X100P is Intel 537 modem, so can I use it as true modem for test? Did any one use X100P as a modem? Thank you very much. -------------- next part

My setup: X100P and Quicknet PhoneJack. I can't seem to properly set up a Zap channel for my X100P. Here are some of my configurations: [zaptel.conf] fxsks=1 #X100P fxoks=2 #Quicknet PhoneJack defaultzone=us loadzone=us [zapata.conf] [channels] context=local signalling=fxs_ks channel->1 ;X100P [extensions.conf] ... [local] exten=>_NXXNXXXXXX,1,Dial,Zap/1 ;I'm pretty sure the

Hello, Can anyone tell me what the "normal" number of interrupts per second is for an X100P card? I've used FreeBSD 5.3 and a linux 2.6.11 kernel on the exact same hardware (only the disk changed) and `systat -vmstat 1` on FreeBSD and `procinfo -dS -n1` under Linux. For both, I'm seeing roughly 1000 interrupts per second on my X100p card. It was a bit worse under FreeBSD, and I

PROBLEM: My x100p only does bad things. When I plug the line from the wall into the card, other phones in my house go nuts, no dialtone, crazy clicking, random tones, etc. Following the steps below, the line is screwed up any time I test after step 2. Just plugging the line from the wall into the x100p takes my other phones off line. External calls to my line hear busy. Obviously, can't

I have an X100P used, at present, largely for outgoing calls. It shares the single incoming POTS line with a number of analog phones. Is it possible to talk the X100P (Zap/1) to answer a ringing call only if I ask it to? I'd like to use only the SIP phone in my office, but let the analog phones continue to work in the rest of the house (until I can afford FXS cards anyway..) I can force

Hi, I'm thinking of purchasing a TDM400P card and was wondering if anyone has experienced any echo issues with phones off these cards connecting to the PSTN via the X100P cards? I have had my fingers burnt with a Voip phone > X100P. Cheers, Taff. --------------------------------- ALL-NEW Yahoo! Messenger - sooooo many all-new ways to express yourself -------------- next part

Thank you for your time. I've put my replies to your questions in-line, below. On Wednesday, June 07, 2017 10:19:41 AM Antony Stone wrote: > On Tuesday 06 June 2017 17:54:59 Mike Diehl wrote: > > > Hi all, > > > > I'm upgrading to Asterisk 13.14.0 x86_64. During my beta testing, I've > > discovered that my server crashes as soon as I leave a

I'm looking to add a single FXO port to my Asterisk box. It looks like my options are a Digium Wildcard X100P off eBay for $6.99, or a Wildcard TDM400P with an FXO Module from Digium for $125. Can anyone explain the tradeoffs (other than the ability to put 4 FXO/FSO modules on the TDM400P). What about RTC for the system - I know the TDM400P provides it. Does the X100P? Thanks!

I was told the X100P will have issues if installed on a line with a DSL connection. Is there a card that will work correctly on a DSL connection? Thanks!! -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040504/6de6226b/attachment.htm

I have an ubuntu 8.10 machine. Linux 2.6.27-14-generic i want to configure a x100p card an use it with asterisk, so i download, compile and install: asterisk-1.4.24 dahdi-linux-2.1.0.4 dahdi-tools-2.1.0.2 libpri-1.4.9 i try almost everything i found on the net but without success: if i run lspci: 04:06.0 Communication controller: Motorola Wildcard X100P when i run dahdi_hardware appears this:

Yo all, I have a problem with a Dutch (KPN) PSTN-line, connected to an X100P. The call wil sound OK at first, but after 10-20 minutes, the audio will start to crackle. Soon after that, this crackle turns into a continuous noise and the parties won't be able to hear eachother anymore. It also sometimes happens that the party on the TDM400P hears a very loud, short-delay echo of themselves,