similar to: Setting MSN for outgoing ISDN calls

Hello, I have a little problem with signalling. An E100p is connected to an Alcatel PBX, wich has an E1 to the outside. Located in Germany. zapata.conf: switchtype=euroisdn pridialplan=local prilocaldialplan=local overlapdial=yes signalling=pri_cpe .... With asterisk 1.0.2 I can call from a SIP phone to a phone connected to the Alcatel and the SIP number is correctly displayed at the caller.

Hi, I'm using a Junghanns Quadbri ISDN card on some lines from the Austrian Telekom. Things are working, the only missing stuff is to add a "0" as a prefix to each incoming call, to make it possible to answer missed call lists. I'm using the 0 as the prefix for outside lines. I've experimented a little with the prefix settings in zapata.conf, but without success:

Hi there, I've got a small problem with the zaphfc channel. No MSN of an any incoming call which comes trough the ISDN card (Acer ISDN, with HFC chipset and zaphfc driver) which will be forwarded to the SIP-Phone will be displayed. Always it will be shown "asterisk" an the Display. --- snip (zapata.conf) --- [channels] language=de switchtype = euroisdn signalling =

Hi list! I am installing an * box that will be installed on a site with KPN BRI ISDN in The Netherlands. I am using bristuff fron Junghanns. Does anybody know the correct settings for this? I will not have internet access there which makes it harder to google around on location. switchtype = euroisdn is pretty obvious but what about these settings: signalling = bri_cpe_ptmp ; p2p TE mode

Hi all, I really hope that you guys can help, because I've been tearing my hair out for the past 5 hours on this one. I have a Zaphfc (BRI) card in TE mode connected to the S-Bus of a Nortel Meridian phone system. Phone calls from the Nortel to say MSN 510 are correctly being sent to the right SIP phone. When asterisk dials say Zap/g2/224 (a Nortel internal extension) the call goes

hi. could somebody explain how exactly the following parameters in zapata.conf work: pridialplan prilocaldialplan internationalprefix nationalprefix localprefix privateprefix unknownprefix the wiki & comments doesn't quite explain them. and phone companies are absolutely no help. i've setup systems in the US & China with trial & error until it works. now i'm setting up a

Hi!I've installed Asterisk@home and I have a ISDN card,(Cologne Chip Design GmbH ISDN network controller [HFC-PCI](rev 0.2) This is how I installed bristuff: how to install hfc card after unload asterisk and amportal whit amportal stop type "setup" unselect zaptel in system service... and set the lan --->reboot<--- cd /usr/src wget

My international calls are not connecting. [general] pridialplan=dynamic ;prilocaldialplan=unknown internationalprefix=00 nationalprefix=0 localprefix= I have the above in my zapta.conf - yet when I dial an international number, I get a ring, then I get the message "the person you are calling, is currently unavailable" This is an ubuntu machine, with a sangoma card, with

Hi, after a few of upgrades, I noticed these messages in full debug log: Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring switchtype Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring pridialplan Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring prilocaldialplan Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring overlapdial Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring

Hi list! What exactly is the meaning / function of the pridialplan & prilocaldialplan? I've been trying to find out what the different possibilities for these settings are but couldn't find a clear answer. The possible parameters I could find are are : local,unknown,dynamic,national,international and maybe there are more? Thanks!

Hello, I have a problem with the Bristuffed version of Asterisk. I have tried Bristuff-0.3.0-pre-1m,n,o,p (Asterisk 1.2.6 to 1.2.7.1) but they all have the same problem it seems: The setup: A machine with a single hfc-s PCI BRI adapter running Gentoo 2.6.15. Asterisk 1.2.0 (BRIstuffed-0.3.0-PRE-1) installed and working perfectly. Grandstream gxp-2000 as a SIP phone, and a normal mobile

I've got a bit trouble with callerid and zaphfc cards. Basically zaphfc doesn't add the "0" in front of national numbers (haven't tried a international call yet). With chan_capi that allways worked fine, however i had to define the national and international prefixes in capi.conf. Is there something similar in zapata.conf ? Here is my zapata.conf: [channels]

Hi all, I've been batting my head against a brick wall for the best part of the day and still haven't got any further (apart from getting a big headache, that is). I've searched the Wiki and Googled the hours away, but I still can't find supportive documentation. I've just replaced my ISDN Fritz!/chan_capi setup with a HFC/Zap configuration and had the following problems: 1

Hi, When startin * it tells me: ================================ [chan_zap.so] => (Zapata Telephony w/PRI) == Parsing '/etc/asterisk/zapata.conf': Found Sep 3 17:21:59 DEBUG[1076873856]: chan_zap.c:1208 update_conf: Updated conferencing on 1, with 0 conference users -- Registered channel 1, PRI Signalling signalling Sep 3 17:21:59 DEBUG[1076873856]: chan_zap.c:1208 update_conf:

Hi everybody, I'm facing a strange problem after upgrading Asterisk from 1.0.9 to 1.2.4. Sometimes, when receiving an incoming call from pstn, although my sip phones ring correctly (I've got both softphones and hardware phones), noone can pick up the call. Asterisk CLI shows me that the phones are ringing, then nothing happens, so there's no problem _after_ someone picked up, simply

Hello, I recently bought a Junghanns Octobri Card. I have some problems with this card to make outbound calls but I can receive calls. I have 3 lines to PSTN and 3 lines to my existing PBX FRANCE TELECOM <-- OctoBRI --> Asterisk 1.2.4-BRIstuffed-0.3.0-PRE-1h <-- OctoBRI --> PABX e-Generis <----> ISDN Phones |

Hello all, Recently I purchased an QuadBRI card from junghanns.net after some playing around, reconfiguring dialplans etc with the exception of 1 thing everything seems to work: I seem to be unable to set the outbound callerid. The dutch telecom operator (KPN) provided me with 4 MSN's on 1 BRI interface. In the past years I'm more then used to setting the MSN without the leading 0, this

Hi, I'm just in the process of replacing a crappy Siemens PBX with a new and shiny Asterisk system. To connect Legacy equipment I hooked up a small ISDN PBX (DeTeWe OpenCom 36) to one port on a Junghanns.net quadBRI card. That port is configured for NT Point to Multipoint (Mehrgeraeteanschluss) mode. Now I can place calls from the ISDN PBX to the other Asterisk extensions but the other way

Hi all, this time with the complete configuration files... We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable