similar to: test of FXO and FXS in TDM400P

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

I have a TDM21B (A new TDM20B that just arrived plus a X100M that I already had). This card sometimes works, and sometimes only the FXO module is seen. (correction to previous message that incorrectly listed X400M/S400M when I'm using only the single port versions of these modules (X100M/S110M). By "works", I mean all 3 modules have the green lights on the ports on and when

I have a TDM400P with one FXO module and two FXS modules in it. I also have a Wildcard X101P. After trying hard to get things working on various Intel computers, but having echo problems that made it not really usable, I decided to try it on some older PowerPC (Macintosh) hardware running Yellow Dog Linux. Things started off smoothly. Both zaptel and asterisk seemed to compile okay, and both

Hello, I've got an Asterisk server with a TDM400P with 2 FXO modules and 2 FXS modules. This server is connected to 2 PSTN lines and 2 analog phones. In my Zaptel configuration, I've defined 2 groups : one for the 2 FXO's and one for the 2 FXS. The asterisk server is just used to add a little IVR and Voicemail service. Eveything works fine, but sometimes the conversation is

Hi , I have an asterix (1.2.7.1) box with 3 TDM400P and 10 FXO modules, and zaptel (1.2.5). The problem is that 6 modules can't be initaized and i get the folowing error: May 7 09:17:37 WARNING[7739] chan_zap.c: Unable to specify channel 9: No such device May 7 09:17:37 ERROR[7739] chan_zap.c: Unable to open channel 9: No such device here = 0, tmp->channel = 9, channel = 9 ztcfg output

I am having problems getting a Nicherons TDM400P wildcard clone to dial out. Everything appears to be configured correctly, but although I see call progress, it never seems to actually pick up the phone. (The following is a test of 911 emergency, where I substitute 811 [repair service] as the actual number dialed.) *CLI> -- Executing [911 at from-internal:1]

Hi all, A while back, there was a short thread on using the FXS interface from a Primus TalkBroadBand device (a DLink ATA) as a incoming line for the FXO interface on the TDM400P: Primus <--> DLink ATA FXS <--> TDM400P FXO <--> Asterisk In that thread, a couple of people suggested that this does not work reliabley, and the ATA FXS <--> TDM FXO link 'goes

I think I have a bad FXS module on my TDM400P. Channel map: >> >> Channel 01: FXO Kewlstart (Default) (Slaves: 01) >> Channel 02: FXS Kewlstart (Default) (Slaves: 02) >> >> 2 channels configured. >> ZT_CHANCONFIG failed on channel 1: No such device or address (6) The zaptel loads ok, but the wctdm reports No such device or address and stays loaded. The

I've setup * with TDM400P w/1 FXS, 3 FXO modules. I've one analog phone connected to TDM400P FXS module, 1 PSTN line to one of the FXO module(ZAP) , and 2 analog phones connected to Sipura 2000 (SIP). The calls between SIPs and zap phone (fxs) are OK. But 2 issues cannot be solved: 1. To dial to PSTN via zap phone, the setup in extensions.conf with the following exten =>

We're having issues with the FXO/FXS ports on our Digium TDM cards sporadically. I'm wondering if anyone else has had these problems, or if anyone can provide guidance diagnosing or fixing the issue? The symptoms are that the FXO and FXS ports "stop working", usually after 2-4 weeks of server uptime. When this happens, sending a (SIP) call to an analog phone on an FXS port

I have a Digium TDM400p (1 FXO, 1 FXS) with the FXS module connected to a standard analog handset with caller id display (US caller ID). Although it appears that caller id information is coming into asterisk (it shows up in voicemail), I can not get it to display on the analog handset. Is there anything special I need to do to send the caller id info out the FXS port? I've tried a few

Thanks for the suggestion. I have busydetect=yes in zapata.conf. You refer to "Martin's algorithm". Can you provide more details please? ----- Original Message ----- From: "Soner Tari" <list@kulustur.org> Subject: Re: [Asterisk-Users] FXO module in TDM400P (UK, BT) - Hangup detection failing To: "Asterisk Users Mailing List - Non-Commercial Discussion"

Please explain the relationship between modules from the driver (wctdm), the /etc/zaptel.conf file and zapata.conf. Specifically, if I have a FXS module 0 and FXO module 1, what should be used in zaptel.conf and what should be used in zapata.conf? Then finally, in extensions.conf, what is the Zap channel for dialing out? Zap/? % dmesg Module 0: Installed -- AUTO FXS/DPO Module 1:

I've got the latest zaptel and cvs asterisk software loaded on my phone server running FC3. And yes, It's fully updated and udev is setup correctly. I've got a TDM400P with one FXS and one FXO module installed. When I load zaptel and wctdm and run ztcfg -vvv, I get this: [root@asterisk ~]# ztcfg -vvv ZT_CHANCONFIG failed on channel 1: No such device or address (6) Zaptel

Since the irc channel wasn't any help, I will try posting my problem here. I have two TDM400Ps less than a week old in a PC. All of the FXS ports work fine, and all of the FXO ports worked fine up until thisafternoon. If I try to dial in, I get a busy signal, if I try to dial out, all I hear is a very scratchy, very crackly dialtone. If I swap the first FXO module with the second on the card,

I just received a Wildcard TDM400P by FedEx yesterday. I noticed that the FXO/FXS modules use connectors similar to Ethernet. Now, i want to connect the TDM400P to the PSTN connector in the wall, and also to a regular analog phone. Both the PSTN conn and the phone use smaller connectors, typical for analog phones. I searched the "official" docs and the Wiki, there's good

Dear all. I have a tdm400p with an FXO module in slot 4 and an FXS module in slot 1. I have not configured the FXS port in an attempt to keep things simple. The problem is that when I call the POTS number (assigned by phone company) asterisk is seeing the call but then not doing anything with it. The verbose output from asterisk is as follows:

I have a TDM400p with 3 FXS mods and 1 FXO mod. I have all set up with what seems to be correct settings (according to digium and asterisk wiki). As soon as I plug in my POTS line into FXO mod the line goes into offhook state (whether I have power to the card or not). Should this happen? When I try to call * box all I get is busy signal. I've installed stable version, cvs version, change

Hellow everyone, here's an other newby question. I've got a * configured with the card in the subject line. At times Asterisk fails to notice a disconet from the incoming line going into one of the FXO ports. Consequently it just keeps the line off-hook for ever and that causes my provider to mark the line aut of order. Is there any way to "help" Asterisk notice the disconect?

>Asterisk and it works fine untill the following >situation: > >- one of the telco lines occasionally becomes mute after call is completed, would not provide dial tone, (not sure about ringing on that >line) - both via old and new PBX. >- zap show channel <n> would show that line as 'Offhook', though no telephone is off hook. > >If physical line would be