Displaying 20 results from an estimated 3000 matches similar to: "Adjusting gain, Milliwatt and ztmonitor"
2005 Jul 15
2
How to 'read' ztmonitor and set gains
Being one the many people trying to track down echo 'ghosts' I ran across
this page:
http://lists.digium.com/pipermail/asterisk-users/2004-November/071301.html
suggesting ways to adjust the gain. I have a TDM400P 2x2 config with
Kewlstart lines configured. I've located a local telco milliwatt test line,
and when I call it, the gain numbers are no where near 14844. Now, this
2005 Aug 16
0
Echo calibration with ztmonitor and a testlinefrom a telco
The value of 14800 is correct.
I had issues with my TDM400p with 2x FXO's installed and using the Xlite client. I could not get the echo stable at the initial call.
Changing to a hard phone made everything work correctly. I still had problems with the off location I called, but mostly worked great.
To see the TX gain I created an extension with the Milliwatt command attached to it and called
2004 Sep 19
2
Effectively using a telco Type 102 Milliwatt Test line with ztmon itor -v to set txgain/rxgain in zapata?
I am trying to obtain optimum gain settings for a bank of analog lines
connected to a channel bank. My telco has provided a 'Type 102' test line to
use for incoming level calibration. This is functionally equivalent to app
Milliwatt(), but provides tone from the CO inwards.
Question is, how should one use this a 0dbm test source with ztmonitor? Am I
correct in understanding that a 0dbm
2011 Apr 15
1
sangoma card rx/tx gain level
Hey Guys!
We had echo issue before so we replaced old PRI card with Sangoma A102D HWEC. Now my question is i set rx/txgain level 0.0 default do i need to touch this value or default is best. I have read on google and people say it should around 14844 on ztmonitor for rx/tx level same.
I just use milliwatt and test my default 0.0 rx/tx level and it come around 4600. Do you think i need to make
2005 Oct 12
3
Calibrating both RX and TX gain?
Hello!
I'm having an echo problem with a TDM card. The TDM card is being fed by
a channel bank just 12 or so feet away. When you put an analog handset on
the line, both the RX and TX volume seem to be just fine. However, when I
use the TDM card, I have to have an rxgain of 13.5, and even then, the
audio is relatively quiet. I'm also getting echo on these lines, so I
have turned
2005 Oct 11
6
PRI echo issues: solvable?
Hello,
After solving the other "low hanging fruit" audio issues in our Asterisk
PBX, we are left with occasional cases of severe echo which we have not
found a solution for yet.
Our system:
- Asterisk 1.2.0-beta1
- TE110P on a PRI
- TDM04 and TDM40, but these are unrelated to current echo issues
- Fedora core 3
- Echo canceller KB1
Most calls have minimal, acceptable echo levels. But
2006 Apr 04
2
Milliwatt Test Number List
Hello:
Does anyone know of a list of milliwatt test numbers for debugging echo?
Specifically I am looking for a milliwatt test number in Canada,
preferrably in a 416 or 905 NPA exchange....different carriers would
also be nice....ie. Bell Canada, GT, Sprint (Now Rogers Telecom)
I called Rogers NOC and asked them for the milliwatt test number....they
didn't even know what it was....so I
2012 Mar 15
0
AST-2012-002: Remote Crash Vulnerability in Milliwatt Application
Asterisk Project Security Advisory - AST-2012-002
Product Asterisk
Summary Remote Crash Vulnerability in Milliwatt Application
Nature of Advisory Exploitable Stack Buffer Overflow with locally
defined data
Susceptibility Remote
2005 Aug 22
1
How to start ztmonitor in 'quantitative' mode ?
To start ztmonitor in quantitative mode you do the following.
Assuming you are running Asterisk V1.0.9 you need to edit one line to
ztmonitor.c in /usr/src/zaptel as per patch 2783
http://bugs.digium.com/bug_view_page.php?bug_id=0002783
Change line 261
fprintf(stderr, "Usage: ztmonitor <channel num> [-v] [-f FILE]\n");
to
fprintf(stderr, "Usage: ztmonitor <channel
2006 Oct 18
3
Asterisk hangs up on incoming analog calls after a while
I have been experiencing a problem where after someone calls me from
an analog line, the phone call is terminated after a period of time
(anywhere from 15 seconds to 15 minutes) The phone that I use to
answer the call is an Aastra 9133i SIP phone. There are several
other SIP extensions on the network as well as a few analog
extensions on a shared FXS line. When a call comes in the
2005 Feb 14
2
ztmonitor
Good day list,
I am feeling extra stupid this Monday morning and am hoping
someone can come to the rescue.
I am trying to use the ztmonitor utility on my wildfire 4 FXO
card. and have read the following from the wiki.
*********Wiki start********
If you set this to yes, use ztmonitor to adjust the rxgain and txgain.
Ztmonitor isn't installed by default; but it is included with the Zaptel
2006 Dec 15
1
ztmonitor displays full bar when idle
Hardware is an SM56 card (X100P clone). When the line hangs up, ztmonitor
displays full bar (or whatever maximum allowed by rxgain) in RX. It only
drops zero when the line picks up (and remote was silent). Is this
something of concern? The zap channel seems to work despite echo.
Additionally, what's the objective of tuning with ztmonitor? I mean, what
would indicate an optimal level?
2009 Aug 31
0
Clarifying RX and TX gains
I've done gain tuning as per the info I've found online. I've got my
RXGain set so my volumes list as about 14,800 (using a milliwatt test
number and ztmonitor -vv). However listening to the line now, this
sounds too loud to me. The person speaking sounds fine, but I've now
got a large amount of background hiss coming thru. In order to get the
"recommended"
2006 Apr 14
0
Ztmonitor shows RX is always on. FIXED.
Err, stupid me. Seems like the phone is hungup, but when I start ztmonitor,
the line is picked up. I guess the line in India is pretty loud b/c the RX
bounces off the charts, changed it to (-4) and all my problems are solved.
Regards,
Min Chang
On 4/14/06, Kyle Sexton <ks@mocker.org> wrote:
>
> Have you tried putting a Hangup in your extensions.conf?
>
>
>
> On 4/13/06,
2006 Mar 02
5
Milliwatt Analyzer available
Hi,
some days ago we discused here the need for an analyzer
for the 1000 Hz tone, as opposite application to Milliwatt.
Here it is: Mwanalyze
http://planinternet.net/download/voip/asterisk/app_mwanalyze.c
It performs a Fourier analysis for a fixed frequency
and tells the amplitude.
The frequency is not limited to 1000 Hz, but can be passed
as argument. The periode duration must be a mulitple
2005 Aug 26
4
Ztmonitor values when zap channel is onhook
Hello,
In my quest to figure out the source of the random echo on our shiny new
asterisk install, I have been using ztmonitor on the TDM400p channels
for the good part of today.
I have 2 TDM400p cards with 8 FXO modules and 6 pots lines connected to
them (last 2 channels are unused but configured in zaptel). Even when
the lines are onhook, the Tx values settle down to 0 but the Rx values
still
2007 Mar 24
2
TDM analog cards, volume, echo, fxotune, ztmonitor and HPEC
Hi, everyone:
I am developing a system using Asterisk, TDM-400 analog cards, analog
lines, and Polycom SIP phones for internal extensions.
Initially there was bad echo but after a series of efforts, I've managed
to reduce it to a negligible level (it only happens when both parties
speak simultaneously, and even there, only for a few hundred
milliseconds). From an echo standpoint, things are
2006 Apr 13
1
Ztmonitor shows RX is always on.
Details:
Asterisk 1.0.9
Zaptel 1.0
Dell P3 1ghz with X100P Clone
Location: India
This is an interesting issue where when I open up ZTMonitor, it shows the RX
as being on. It seems that Zaptel doesn't know to hang up the line so after
a couple of hours when the telecom cuts the line, everythign stops working.
Things I've tried include playing with the zaptel.conf, trying zaptel
v1.2(with
2010 Jul 09
0
Rx/Tx fine tuning of analogue card to PRI card - Am I right with my theory?
Hi Everyone,
I want to fine tune the Rx and Tx gain on an analogue Sangoma card by
dialing into another server that is running on Sangoma PRI card (both
services on Bell network).
[mwatt1004khz]
exten => s,1,Answer
exten => s,n,PlayTones(1004/1000)
exten => s,n,Wait(300)
If I match the Rx/Tx numbers on both sides by monitoring "ztmonitor X -vv"
am I right with my theory of
2004 Nov 22
1
Test Number in the UK?
In recent times I have seen a few posts which describe how to use ztmonitor to set the rxgain and txgain parameters on an FXO channel.
The starting point is to call a '102 milliwatt test number'
Does anybody know of such a facility in the UK?
Ian
-------------- next part --------------
An HTML attachment was scrubbed...
URL: