similar to: Spa3k and ISDN

My apologies for the off-topic post ... No matter what settings I try, when I dial in to the SPA-3000 on the PSTN line, it picks up the call and immediately gives me a fast busy tone then hangs up. The info tab says under PSTN Line status: Last PSTN Disconnect Reason: PSTN Disconnect Tone which seems to indicate that the SPA thinks the caller has hung up. Since I am in Japan, it is possible

This is a wierd one. Can't figure it out. I have an SPA-3000 at the house handling my incoming line. It's setup to direct the incoming call to asterisk. Works great 99% of the time. A few times a day, I'm getting calls that ring once internally and are then hungup. I managed to get a detailed log [1] of what's happening today and it looks to me that the SPA is acting wierd.

Hello, Just want to tap the collective wisdom of this list as to experiences pertaining to the Handytone HT488 and the Sipura SPA-3000 adapters... Basically I'm looking for a FXO/FXS/LAN ATA and these two seems to be the top of the pick..Any comments and experiences esp. with Asterisk compatibility would be great, before I plonk in the bucks. TIA. /wai-sun

I've had an spa3k in service here at the house for a while now. After some initial wrangling, it's been working okay. I've had to reboot it a couple times and have noticed something rather annoying though. My setup is pretty simple and, dare I say, common. I have the SPA-3000 "inline" between my incoming POTS line and the internal house phone. It's setup to deliver

Arrggghh. Tearing my hair out here. I'm trying to set up the spa3000 in the UK for my home, and want * to control the dial plan I've googled to no avail. I've read the manual to no avail. Can someone, please let me know what the parameters is the spa and * are to a) receive a call from the pstn b) make a call to the pstn from the phone attached I can make sip to sip calls (i.e. I

Dear list, I am playing with Sipura 3000 since last week. Through the wiki pages I could get running it reasonably well. My setup is that of a Sipura, linked with a local analog cordless phone, a local PSTN line and the setup to link to an asterisk server located at a remote static ip address. I can dial the cordless phone from other extensions located at the asterisk server; I can dial out

Hi list, After successfully configuring Linksys SPA3000 and SPA3102 devices as Asterisk PSTN gateways, the only thing I can't get working is the PSTN Caller ID. The analog and SIP phones I've used can both display CIDs for internal calls, while the analog model also displays CIDs correctly when attached directly to the PSTN line. However, when PSTN calls come in via the SPA

Hi list, Hopefully, some of our Dutch members can help with this one. I'm also based in the Netherlands and am using a Sipura (Linksys) SPA-3000 (firmware v3.1.10(GWd)) as a PSTN to VoIP gateway for my Asterisk test system. It works fine, except that the Called ID (CID) is not working. I'm aware that KPN (our local telco) requires a separate subscription to activate CID on POTS

Hello. Has anyone run into problems accessing voicemail with the Sipura SPA-2002's? Our SPA-2000's work fine (registers fine, able to make and receive calls properly & also able to access voicemail). We've configured the 2002's exactly the same way. However, with the SPA-2002 we're unable to access the voicemail system (though it does register fine and is able to

freebsd quite current ports tree 1.01 asterisk spa3k at 2.0.11(GWg) for calls in from the pstn side of an spa3k to asterisk, i get sporadic short beeps. they are not related to sip re-reg time, which is all that has occurred to me so far. calls in from the fxs side of the spa3k and out through nufone do not exhibit the beeps. calls from the fxs side of the spa3k out the fxo side do have the

My SIP phones can dial out through Sipura SPA3k to POTS for local and 911 calls _but_ incoming POTS calls are being swallowup somehow. Am I on the right track with the code snippit below? sip.conf: --------- In sip.conf the following code is _supposed_ to ring the SIP phones when a POTS line call comes in through Sipuara to Asterisk. [spa3k-pstn-in] ; Pots-line-in from Sipura ; If

In my seemingly endless search for the cause of echo on my SPA3000, I wired it up in the following configuration: Analogue Handset <--> (FXS)SPA3000(FXO) <--> PAP2 And set the Line1 dialplan on the SPA3k to '(<:@gw0>S0)' which means that as soon as I pick up the handset I get linked straight through to the PAP2, which gives me dialtone. Even in this configuration, with

We have issues with all of the SPA-2000 ATAs we have where incoming calls from only one of our Asterisk servers do not complete. Details: 1- On the CLI we see that when the call is pushed to the ATA it shows Busy/Congested 2- We can make calls to this same server just fine 3- We can receive calls from other Asterisk servers running older CVS versions of Asterisk with the same exact ATA

Anybody using a Sipura 3000 for FXO with Asterisk? Mine is working except for one small nit... When a call comes in from the PSTN, the Sipura answers it and then passes it on to Asterisk, which plays extension ring tone. I'd prefer for the POTS line to stay on-hook while the extension rings, and to only be answered by the Sipura when the extension answers. Has anybody made this work?

Hi, I found the following on Windows 2000/NT R Version 1.9.1 (2004-06-21) (also Version 1.9.0): The S4 group "Math" doesn't work as documented; i.e., "log", "log10", "gamma" and "lgamma" are included in the documentation but don't work. See example code below. Moreover, what about 'genericForPrimitive' which is used in

Hi, For further calculations I need to extract indivdual Variances of different random effects from a fitted model. I found out how to extract the correlations (VarCorr(m1)@reSumry$group1) but I was not able to find a way to extract the other components individually. To extract the Residuals I tried: (ranef(m1)@ stdErr) which unfortunately did not work. Thank you very much for your help!

Colleagues ---------------------------------- System info: R version rw1020 on NT ESS using emacs ver. 20.4 ---------------------------------- I need to get the means for each column of a dataframe in the list created by splitting a data frame. At present, I am getting the mean of all columns in aggregate. The structure of the unsplit data is: > shuttle.tr1[1:10,] juliandate

I'm experiencing a very unusual problem with a few of my sipuras. They keep over heating after minimal usage. I unplug them and let them sit for 15 minutes and it starts working fine. The other way around is that I put a fan on it or something to keep it cooling. Has anyone else experienced this or are they just defective units? Regards, Mohammed Salim EZZI Telecom, Inc.

Hello All, I am trying to figure out which way to go for a quad port fxo solution with a good echo can on it. My options are the sangoma remora, a mediatrix fxo, or something similar. The issue is that I would need a good EC. This would be on about a 9000 foot loop, and the lines don't function well on a spa-3000 or zaptel tdm 4 port card. Anyone have experience that drives them in a

Anyone know what I need to do to get the FXO port on the SPA 3000 to forward calls to Asterisk? My Asterisk is running on port 5061 and I set the dial plan on the device to forward to s@asteriskip:5061 but Asterisk is not picking it up. I can see on tcpdump traces that the Invite packets do go to through to the asterisk machine on port 5061, but it's not picking them up. sip debug does not