similar to: PRI restarting each hour?

Displaying 20 results from an estimated 200000 matches similar to: "PRI restarting each hour?"

2008 Feb 04
0
PRI ISSUE
hello everyone, Last week I installed asterisk 1.2.24 with digium TE220B card. I have a problem with our PRI and Asterisk: the call be interrupted.It happens either PSTN-to-SIP or SIP-to-SIP,almost every call. After spending several days searching on internet, I found a lot of discussion about this issue and I have tried many, but it still.I am totally new to Asterisk environment and suspect I
2006 Feb 13
1
problem with outgoing calls Unable to createchannel of type 'ZAP' (cause 34 - Circuit/channel congestion)
Nik, Just curious - what is your telco setup? Do you have PRI with the specified D channels? You need to make sure that your telco is set up to have the D channels on 16 and 47. When you first start Asterisk, or when you log on to the CLI, do you ever see messages stating the B channels are successfully started? Let us know. -MC -----Original Message----- From:
2006 Feb 13
0
problem with outgoing calls Unable to create channel of type 'ZAP' (cause 34 - Circuit/channel congestion)
hi i've configured a TE205P on asterisk at home this is my zaptel.conf span=1,0,0,ccs,hdb3,crc4,yellow span=2,0,0,ccs,hdb3,crc4,yellow bchan = 1-15, 17-31 dchan = 16 bchan = 32-46,48-62 dchan = 47 loadzone = it defaultzone = it and my zapata.conf signalling=pri_cpe ; pri_cpe = PRI slave ; pri_net = PRI master switchtype=national usecallerid=yes hidecallerid=no callwaiting=yes
2007 Feb 02
0
Line drops
Hello to all, I post again (last time subject: Line drops strange problem(got event On hook) because i have caught in debug a situation where i get a call and the line drops and i get a call from the same caller and the line works well and the call normally closes by both parties. The only differences i find are underlined. If someone can understand the reason why the line drops from the debug
2007 Jan 31
1
FreePBX/Debian Aborts Call While Connecting
I used the "FreePBX on Debian" HowTo at http://powerontech.com/freepbx-on-debian.htm to install. I use callfiles to initiate calls to my SIP carrier. They get my registration, but they see that my call is interrupted before they can complete the connection. My Asterisk log shows that the call times out after the time (45s) specified in my dialplan Dial() command. What is wrong? [from
2006 Feb 08
1
incoming call release after 1 ring
Hello, Can somebody please assist me with my problem. Currently I am using a Asterisk@HOme version 2.4 with a TE406P digium card. One the E1 is connected to a telco switch via an ISDN. May issue is that may incoming calls in the zap channels gets disconnected or release after 1 ring. I really dont know what setting should I change to increase the timeout of the ring. I have even tried upgrading
2006 Jan 06
0
IAX2->SIP dropped calls
Apparently we've been having calls sporadically drop. We're using an IAX outbound trunk and SIP adapters on the inside. Below is a log excerpt detailing one of the calls which dropped, and it looks largely normal to me except for this: Jan 5 13:31:07 DEBUG[3776] channel.c: Didn't get a frame from channel: IAX2/teliax-2 Jan 5 13:31:07 DEBUG[3776] channel.c: Bridge stops bridging
2007 Jul 04
2
Xorcom Bri and asterisk crashes
We have recently install an asterisk solution with about 60 physical extensions. While the system is running it runs reasonably well (Still have a few teething problems) but twice now they have experienced a degradation in voice quality and dropped calls and then finally asterisk completely crashes out. Restarting asterisk will work for a little while and it will crash again, each time less time
2006 Feb 14
1
fax pass-through
hi, after upgrade from 1.0.x to 1.2.x i cannot send faxes my topology: PSTN<-wct4xxp-asterisk- -sip- ata (ht496,ht488,asus vp100) - samsung sf2500 fax log: Feb 13 23:50:35 DEBUG[27914] chan_sip.c: Allocating new SIP dialog for 20d700003cb20000@192.168.1.209 - INVITE (With RTP) Feb 13 23:50:35 DEBUG[27914] chan_sip.c: **** Received INVITE (5) - Command in SIP INVITE Feb 13 23:50:35
2005 Sep 29
2
Is this normal?
Hey, I'm up and running fine with 30 Polycom 500s connected to Asterisk 1.2Beta on Cent OS 4.1 with a Digium TE110 connected to a PRI line. Nearly every hour, almost on the hour I get this: Sep 29 23:01:38 VERBOSE[3567] logger.c: -- B-channel 0/1 successfully restarted on span 1 Sep 29 23:01:38 VERBOSE[3567] logger.c: -- B-channel 0/2 successfully restarted on span 1 Sep 29
2009 Jul 08
3
Restarting of B-channel on span 1
Hi All, Hope you all are fine and good, Today i have found that Mine all PRI Channels are restating after every interval of one hour, and i have search and psot on fourms and everyone said that this is a normal behaviour. If this is a normal behaviour is there is any way to stop it { i still don't know what is the reson to restart ever hour } . Because this is listed everywhere that
2007 Sep 30
0
Asterisk Dropping Calls (Richard Young)
> > Hi, Remove usecallingpres=yes busydetect=yes from your zapata.conf file. and the restart asterisk. Hopefully you will not faced drop call issues. Regards, Vidura Senadeera. Message: 3 > Date: Mon, 24 Sep 2007 12:29:40 +0100 > From: "Richard Young" <Richard.Young at intrintech.com> > Subject: [asterisk-users] Asterisk Dropping Calls > To:
2007 Jan 31
0
Line drops strange problem(got event On hook)
Hello to all, I have a strange problem with my asterisk. Line drops while i am in a call and without a reason.The line drops no matter if it is a incoming or outgoing call and it happen while i am talking on the phone (no silence detection problem). I tried to debug the situation and the only strange thing is the "got event On hook" (i guess..). I am thinking that it is a problem
2006 Mar 31
4
cannot set outgoing cid
Hi, sorry for the long debug output below. I configured Asterisk with AMP to send the whole number including the extensions of the callers to the called party. Whatever I configure in AMP it looks like it is used, In my eyes it is ok, but doesn't seem to work. 033811234451 is the call id i configured, and it seems to use them, but the caller will only see a 0338189040 instead of my
2007 Sep 24
0
Asterisk Dropping Calls
Hello, I am having an issue whereby calls are being dropped randomly. I have an ISDN 30 E1 line going into a Wildcard TE220 (4th Gen). My Asterisk install is based on Trixbox 2.0. However, I have updated the source code to the following. The Asterisk release is asterisk-1.2.20. Zaptel release is zaptel-1.2.18. And libpri release is libpri-1.2.4. I have include an extract from the Asterisk log
2006 Nov 21
0
Nortel CS1000 Asterisk with SIP
Skipped content of type multipart/alternative-------------- next part -------------- Nov 21 14:17:47 VERBOSE[32580] logger.c: <-- SIP read from 172.25.103.222:5060: INVITE sip:1715;phone-context=exp_net.ascom@ascom.be:5060;maddr=172.25.96.48;transport=udp;user=phone;x-nt-redirect=redirect-server SIP/2.0 From:
2006 Feb 02
0
Agents, queues and zombies
Hi all, Have been experimenting with agents and queues instead of placing calls direct to a user's phone extension, but I've run into problems with calls to both the agent and the extension which creates a zombie and double records calls abandoned etc. We're using a unique queue for each agent (only a handful of users) to try and get some agent/queue information to see what the
2006 Dec 04
2
Odd queue issue
Hi, I have 2 systems (A and B). I have an 800 number... when someone calls the 800 number it goes: IAX2-->A---IAX---B--->SIP PHONE However.. if the user calling the 800 number is a SIP user that is registered to A it goes: SIP--->A---IAX---B--->SIP PHONE This is the problem... when a call comes in from the IAX2 800 provider, things work fine... however if a SIP user registered to
2006 Feb 22
0
Outbound problem sip chanel
I setup my aah box with a sip trunk at irisxa.iristel.net Incaming it is ok but when I try to dial 8 and the nr where I want to call I get all line is busy. In my log I have these: Feb 22 14:33:04 DEBUG[3156] manager.c: Manager received command 'Command' Feb 22 14:33:04 DEBUG[3156] manager.c: Manager received command 'Command' Feb 22 14:33:19 VERBOSE[2721] logger.c: --
2006 Mar 26
1
AAH: DNID not set if caller suppresses CID?
Hi, using asterisk@home, with quadBri from junghanns.net I am facing a strange problem: I have set incoming routes for some extension / DID: [ext-did] include => ext-did-custom exten => 23,1,SetVar(FROM_DID=23) exten => 23,2,Goto(ext-local,23,1) exten => 57,1,SetVar(FROM_DID=57) exten => 57,2,Goto(ext-local,57,1) exten => 66,1,SetVar(FROM_DID=66) exten =>