similar to: Polycom phones and dynamic IP for NAT

This is not an Asterisk specific question but doesn't anyone know if you can automatically prepend a 9 on the call lists so clients can return dial without having to repunch in the number? If you go to directories now it just shows the number without a 9 (obviously). Maybe on the Asterisk side?? Bill -------------- next part -------------- An HTML attachment was scrubbed... URL:

192.168.1.107 199 6bd3fb49505 00102/00000 ulaw No Tx: ACK 192.168.0.100 110 5c5a4953-65 00101/00005 ulaw Yes Rx: ACK Those channels are stuck talking to each other. The phones are disconnected yet that connection remains. I can clear w/ a restart obviously, but is there any way to tear down a call like that from the CLI? Bill -------------- next

Ok so I added to my Freepbx config running Asterisk 1.2.4 in extensions_custom.conf ; intercom exten => _7XXX,1,SIPAddHeader(Alert-Info: Auto Answer) exten => _7XXX,2,Dial(SIP/${EXTEN:1},12,Tt) and configured my Polycoms via this page http://www.voip-info.org/wiki/view/Polycom+auto-answer+config for auto answer and that works fine if I dial 7 then the 3 digit extension. No

I have read that 1.4 has shared line appearances, which I assume will work with Polycom phones. Has anyone configured this and verified it working? I was going to start playing around with it but wanted to see if anyone else has tackled it yet. Bill -------------- next part -------------- An HTML attachment was scrubbed... URL:

This is not necessarily Asterisk specific but if I have Polycom 301/501 and 601s and want to dial a missed call back, how do I prepend a 9 - can I do this via the polycom config? I can't find anything in the docs. Bill -------------- next part -------------- An HTML attachment was scrubbed... URL:

I've been playing with Asterisk for a few weeks and it's working great. I have a question about getting multi-line receptionist phones working. I was thinking about getting one of these expansion ports: http://www.cisco.com/en/US/products/hw/phones/ps379/products_data_sheet0 9186a008008883d.html What are people using for receptionist phones that show all the extensions in

I have a situation that has repeated itself a few times. Someone calls into Asterisk and is connected with a voice extension. At some point during the call, the log shows "chan_zap.c: DTMF digit: f on Zap/2-1". At this point, the call is redirected to receive a fax and the Asterisk voice extension is hung up. The users report that there were no noticable tones heard just before the

I?ve been tearing my hair out trying to get a Polycom phone (behind a NAT) to register to an * box behind a Cisco SIP ALG. With known good credentials configured on the phone and in *, I get 403 Bad Auth when trying to register. If I put the phone onto the same LAN as * it works fine without changing any authentication parameters whatsoever. If I make the secret blank (null) on the phone and *,

A follow up (late better than never) Finally had time to sit down and look at this sip.cfg <keys key.scrolling.timeout="1" key.IP_500.31.function.prim="BuddyStatus"/> This turns the Services key which I never use on a 501 into the Buddy Status. It even works while on a call. One touch! Bill ________________________________ From: Bill Gibbs

I know this is not asterisk specific but we all know this group is used for Polycom issues as well... I have hints working ok on Asterisk. However the Polycom phone will only show the buddies key if there is not a call. This defeats the purpose of using the buddies to see if you can transfer a call to another extension (using the Buddy key to see if they are on the phone). Polycom sip

Hi All, Has anyone gotten the polycoms or the linksys phones to accept oprtion 66 on the dhcp request for the address of the tftp config server? We have the dhcp server issuing the proper IP of the tftp server, but the phones just sit there and never try to contact the tftp server for their configs. We can see the proper option going from the dhcp to the phones with ethereal trace. Thanks JR

2 Asterisk servers 1.2.12.1 Connected via IAX2, same switch, GigE, no packet loss, etc 1 with a Sangoma A101 for a PRI to the PSTN Ulaw QoS enabled NAT for the registered ATA boxes, no nat between the * servers Faxing inbound: Call from PRI hits the first Asterisk server Then talks to the 2nd via IAX2 NVFaxDetect receives the fax, converts to PDF and emails it out Works great!

Hi everyone, I have been dealing with a certain issue with a particular customer site for months now. The problem occurs when there is an error with caller id as shown in the following: WARNING[16036]: chan_zap.c:6309 ss_thread: CallerID returned with error on channel 'Zap/3-1' When this happens, it appears that the call still goes through as I can see the caller still navigating

I have looked at the wiki and the mailing list. But I need to find how do we setup the external IP address and the rtp ports for the Polycom IP-500 and IP-600. There web interface has a nat setting but can't find instructions on how to set this up. I would like to set this up via there ftp file setup instead of via there web setting. Also There QoS settings are set to 5 and 2 but there it

Contact me off list, I have a sample extensions.conf file that I can share. It has Paging (one to one and One to Many) Ivr includes, time of da routing and it is geared towards Polycoms. > -----Original Message----- > From: asterisk-users-bounces@lists.digium.com > [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of > Thomas Johnson > Sent: Friday, January 20, 2006

Hi, everyone, We've been reasonably happy with Polycom SoundPoint phones, but we only have them installed on the LAN. I've read that they have problems working across NAT. So ... I guess I have a few questions. First, is there a way to get Polycoms to work well over NAT? If not, then are there phones of comparable voice quality that do work well over NAT? Without costing a lot more?

I'm having some trouble with Polycom Soundpoint phones. I have had good luck deploying them on a local network, but now I've tried putting some in place which access their * server across the network. The * server is on a public IP and the polycoms are behind a NAT on a cable modem broadband connection. Every so often I get: May 27 16:12:08 NOTICE[29728]: Peer 'Polycom1' is now

Wondering if anyone has experienced an intermittent one way audio (called party can not hear) problem in these conditions; Several IP501 phones local, same subnet. Remote asterisk No NAT anywhere Polycom IP501 ulaw only, canreinvite=yes Asterisk Call termination path is to a sonus GSX operated by the upstream carrier, ulaw only, canreinvite=no The idea is that if the Polycoms are

Guys, this is a weird question but has anybody disabled the blind button that appears on polycoms or know if you can disable the use of blind transfers on polycoms to make any transfer attended? Thx!

Does anybody happen to know the input power specs for the Polycom IP 500 and IP 600? We've mixed up our power supplies and we've got a whole box of them and can't figure out which go to the Polycoms. I would rather not kill the phones by trying random ones....