similar to: Asterisk TS-1

Hi List, Yesterday night after a power off due to a faulty UPS my asterisk doesn't want to start anymore. Here is what I get on the CLI: Asterisk Ready. *CLI> Disconnected from Asterisk server: Bad file descriptor. Executing last minute cleanups == Destroying musiconhold processes Asterisk uncleanly ending (0). I use 1.2.7 I think on a debian sarge and cdr_pgsql too. Any ideas?

Hi, I am looking to connect 66 analog phones to an asterisk box. I was thinking of a Xorcom astribank 32port (2 of them and another 8 port). this is because the phones have no near connection to an ip network, so replacing the phones in favor of voip phones+network cabling is kinda out of the question. In your experience, will these units support all the phones talking at the same time with

Hi, understand that the bandwidth utilized for each call is dependent on the codec used, wonder if Asterisk can monitor the total bandwidth utilized and restrict/reject new calls when the resource is insufficient to support them reliably? Regards Andy Tan -- Andy Tan andytan@fastmail.fm -- http://www.fastmail.fm - Does exactly what it says on the tin

Hi List, I am working on least cost routing code on the moment, and I am stumbling on a problem. Say you have provider A having: Prefix XXX 0.10 Prefix XXXYYY 0.20 And provider B having Prefix XXX 0.15 You're stuck, because you cannot decide if provider B's "XXX" prefix also covers XXXYYY numbers or not. If it doesn't, it would be a waste

Hi List, Being very new to Xen I have a few generic questions for the list, I hope to grab some useful advice and pointers to documentation. I am evaluating Xen to consolidate a few existing servers into one appliance (mainly in order to reduce power consumption, heat, and hardware failure risks). I plan to have a SER router, an Asterisk LCR router, a voicemail server, a calling card server

Slightly OT, but I think this is of possible interest to many of you, I need to get a UPS for my asterisk box. They are rated in VA but I can't quite figure out how that converts to real life. I have a PIII-800 box with two X100P and one TDM400P plus graphics adapter, an IDE hard drive etc. Will a small 400VA box be enough for this? tia

Hi List, I am looking for a 1 FXO analog termination device, other than the obvious PC + FXO card, and which can achieve decent call quality. The SPA-3000 seems an option... have you got any other ideas? Cheers, Jean-Michel.

Can anyone point me to a reference or sample config for bypassing a nailed up (point to point) t1 between two PBXs with asterisk and a pair of t1 cards? Right now I have 2 Nortel norstars connected to each other via a leased line t1. I also have a solid 10mbps low latency microwave link between the 2 sites. My goal is to run an asterisk box at each end with a t1 card and Ethernet card to

I haven't dealt with Centrex for a long time, and one of my customers is being courted heavily by a Sprint salesperson. Am I not correct in assuming that each "line" of Centrex corresponds to an "extension" in the PBX world? This site has 2 POTS lines and 5 extensions, and they told me that for the same thing they're paying right now (~$40/POTS line) they will be

Hi List, Is there a way to tell asterisk to only accept SIP streams from the same IP address that is used for signaling? Thanks, Jean-Michel. -- Jean-Michel Hiver - http://ykoz.net/ D?couvrez la R?union des Technologies IP & Telecom TEL: +262 (0)262 55 03 98 - RCS 434 273 330 SAINT PIERRE

Hello, I had a partner of mine present a Centrex 21 brochure and ask how many of those features can I fulfill. There is nothing out of the ordinary, it's stuff like call hold, call forward, 3-way calling, etc. Has anyone assembled a how-to that shows how to configure PBX or Centrex type functionality? I found one in the voip-info wiki but only a couple of topics were filled out. Regards,

Hello all, I am working on setting up a basic Asterisk system (using Digium FXS and FXO cards, Polycom IP phones). I've got a few questions in regards to voicemail and was hoping that someone could give me some ideas... Right now we have three incoming POTS lines. There are times when all three lines are used. When the lines busy out, the incoming call is sent to a voicemail

anyone know of a solution where mobile handsets out roaming the pstn cellular network can be used and treated as full fleged centrex extentions, i.e. I can transfer a call that comes in on a wired centrex copper pair out to a cell phone and the cell phone can transfer the call back or vice versa where the cell phone recieves the call directly and can transfer to the office all without hairpinning

The benefits of * are obvious so that part of the marketing an * solution is easy. Anybody care to share ideas on how to target companies who would benefit most from */Digium? It seems to me that it would be an easy sell to small/medium companies who need advanced features such as ip trunking, IVR, Conference bridging, etc., etc. I would like to find a way to identify multi-location companies

Greetings, List. I have my Asterisk box setup with 8 Centrex lines that were "left over" from our old PBX system. My boss is asking me to set up Asterisk so that he can flash hook and make an outgoing call on the same line to have a 3 way call. This is what he wants to do: 1) Incoming call on his Centrex line 2) Flash hook and dial a new number (goes out the same line) 3) Flash

Hello, I am trying to update to dahdi 2.2.1. But somehow the xorcom (2BRI) device does not want to work. I pasted below the information I have. pbx at loicvoip1:~# /usr/share/dahdi/xpp_fxloader reset pbx at loicvoip1:~# /usr/share/dahdi/xpp_fxloader usb 'xpp_fxloader'[4937]: --------- FIRMWARE LOADING: (usb) [1 devices] ..Got all 1 devices 'xpp_fxloader'[5003]: ---------

Hi List, I was wondering if anybody had tried running Asterisk inside virtualization software such as Xen. Are there known problems doing it? Cheers, Jean-Michel. -- Jean-Michel Hiver - http://ykoz.net/ D?couvrez la R?union des Technologies IP & Telecom TEL: +262 (0)262 55 03 98 - RCS 434 273 330 SAINT PIERRE

Hi List, I've had some issues with some VoIP providers where either: 1 - There is massive PDD but finally the call goes through 2 - There is massive PDD but the call gets rejected anyways I was wondering if there was a way to automatically detect such behaviors when it happens (maybe with a script or something) so I can take the faulty providers out of the routing and maybe automatically

Hi List, I have a 2Mbps SDSL link which gets saturated during peak time because about I have about 3 E1 worth of g729 traffic going thru. So I'm planning to use IAX2 trunking to reduce bandwith requirement and squeeze out each and every bit of this (expensive) bandwith. I've set up two boxes (debian etch), one in a remote data center (which has plenty of bandwith) and one behing

Hey guys. If my Asterisk box connects to the PSTN using SIP and IP over ethernet and doesn't require any authentication, what sort of a trunk would need to be created? Thanks, -- Nick e: nick.hoffman@altcall.com p: +61 7 5591 3588 f: +61 7 5591 6588 If you receive this email by mistake, please notify us and do not make any use of the email. We do not waive any privilege, confidentiality