similar to: Asterisk cut offs on TE110P

Hello everyone, I've suffering cut offs after 6 or 7 seconds a call is answered, incoming calls are working fine, but outgoing ones show the gollowing messages when are being dropped: [2013-05-15 12:55:14] WARNING[3569]: chan_sip.c:3641 retrans_pkt: Retransmission timeout reached on transmission ZjJkZjlkZWMyZTE4ZmY2NWZlZTExNDM1MDRhMTY4MTc. for seqno 2 (Critical Response) -- See

Hello Approximately every 15 minutes I'm getting the following error (on all channels): [Apr 7 01:34:27] WARNING[6530]: chan_zap.c:6628 handle_init_event: Detected alarm on channel 31: Yellow Alarm [Apr 7 01:34:27] WARNING[6529]: chan_zap.c:2388 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! [Apr 7 01:34:27] == Primary D-Channel on span 1 up

Hi all, I'm sure something similar has been discussed, but one can only wade through the archives for so long. I'm setting up a T1 and my telco has a bunch of questions it wants me to answer. I know much of the TE110p is configurable to do any of this, but I wanted to know if there is an optimal or preferred setup. Any help would be appreciated. Here is the quiz my telco is giving me:

Hi all, I'm sure something similar has been discussed, but one can only wade through the archives for so long. I'm setting up a T1 and my telco has a bunch of questions it wants me to answer. I know much of the TE110p is configurable to do any of this, but I wanted to know if there is an optimal or preferred setup. Any help would be appreciated. Here is the quiz my telco is giving me:

Hi All, I have a TE110P in E1 mode, in a dell poweredge 250. The 30 channel E1 supplied is from a telco in Australia, with the following in my zaptel.conf: span=1,1,0,ccs,hdb3 bchan=1-15 dchan=16 bchan=17-31 (yes the provider has NOcrc4 for some reason) After installing the latest cvs libpri and zaptel, I successfully loaded the kernel modules. The card is verified as not sharing an

I'm not 'overly' new to asterisk, but I am very new to the Digium card / Telco aspect of it. I was able to get a TE110p card, installed.. and hooked a t1 up to it. I'm using zttool to just look at 'some' output. Here is what it looks like when I just load it up: Current Alarms: No alarms. ? ? ? ? Sync Source:

I'm getting unstable behavior with my newly installed TE110P T1 card. It hangs up any incoming call anywhere from 20 seconds to 6 minutes. Frequently, when you call back on our incoming T1 there'll be an automated announcement (maybe from the telco?) stating "we are unable to complete your call at this time". I simultaeously get a yellow alarm on the system and shortly

Hi!, this issue makes me crazy. I read a lot of docs, also * mailling list and I try a lot of things without success. Any help will be appreciated. Here is the info: Hardware: -------------------------------------------- Supermicro Server with motherboard X7DB8, chipset Intel 5000P, Xeon 5050 Digium TE110P Software --------------------------------------------- Asterisk version 1.2.12.1

Does anyone know of a way to log when a user logs off using Samba as a PDC. I have Samba 3.0.2a and can log log-ons using root preexec on a share all users mount, however I do not know of a way to log log-offs. We need this data for record keeping purposes. We don't use roaming profiles, so using root postexec is not an option as shares disconnect when not in use. Thanks for any help,

Hello, Digium support kindly proposed to ship a TE120P card to help resolve the issue. I plugged in the card, and introduced the loopback plug. I cleared the red alarm for a while and then i started seeing alarm switching from Yel/Recovering to Blue/Rec with a lot of IRQ Misses. I call Digium that assisted us, and we noticed IRQ sharing with the VGA adapter and the Ethernet port. I changed

Fedora Core 6 regards, Pablo. On Thu, Mar 08, 2007 at 05:01:15PM -0800, Jose Bertuzzi wrote: > Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: > ??? Alarms Span ??? OK Digium

Hi everyone I have a Digium card TE110P and after plug it, turn on the computer and configure, the LEDs don't light up in spite of what Digium FAQ says about the LEDs: When will the LED's light up on my TDM400P/TE110P/TE2XXP/TE4XXP? ... The TE110P LED's will light up RED when the span is configured and kernel module is loaded. If configured correctly and a circuit or channel bank is

Hi All, I have configure my Asterisk as follow (using Asterisk@home): [zaptel.conf] span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 loadzone = uk defaultzone=uk [zapata.conf] [channels] switchtype=euroisdn pridialplan=local prilocaldialplan=local internationalprefix=00 nationalprefix=0 usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley

Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: ??? Alarms Span ??? OK Digium Wildcard TE110P T1/E1 Card 0 ??? OK Digium Wildcard TE110P

Hi folks, I've already searched the mailing list but no one else seems to have my same problem. I'm using Asterisk with the following configuration: Fedora Core 4 (but I also tried Fedora 3) 1 Digium TE110P 1 TDM40B 1 HFC-S 'Cologne' bristuff 0.2.0-RC8o (zaptel 1.0.9.2) I compiled right, I can load kernel modules but when I try to unload wcte11xp module (the one

Hello every body, I ve installed Trixbox 1.2 on "DELL OPTIPLEX GX 240", i upgreded it to the latest version. I've 2 cards installed in the same pci channel via a bridge or plug i don't know exactly what's his name( but a card (1 pci) that gives 2 pci channels) the first card is TDM400P: it's ok the second is TE110P: it's not ok . No led is on neither the red nor the

Hey there, What recommendations does anybody have as to motherboards known to work well with the Digium TE110P T1 interface cards and the TDM400P analog POTS interface cards? We currently make use of the TE110P for our T1 (esf w/ b8zs - not a PRI) and have experienced many issues caused by our PBX's motherboard. Additionally, we built a server to become our new PBX, but that machine runs

Hi All I have a TE110P card connected to a PRI line. In my zaptel.conf I have: span=1,1,0,esf,b8zs bchan=1-23 dchan=24 loadzone = us defaultzone=us and my zapata.conf is: [channels] context=inbound-pri switchtype = national pridialplan=unknown ;pridialplan=international signalling = pri_cpe callerid=asreceived busydetect=no usecallerid=yes hidecallerid=no callwaiting=no callwaitingcallerid=no

Hi, thank you for last info. we've tried to use te110p but failed. We're quite surprised that cable wasn't included with the card as any documentation, at least on HW setup and installation, yet cable pinout for connection to PRI interfaces.... 1. We have followed instructions on your site and from Beronet guide, but card just keeps blinking and nothing happens (also no useful

Hi everybody, i need someone to tell me the spins numbers of Rx+,Rx-,Tx+ and Tx- of TE110P and also if you can tell me have to made a cable like that?? Modem Teleco <-----------Self Crosscable------------>Asterisk Rx+ <--------------------------------------------------------------> Tx+ Rx- <--------------------------------------------------------------> Tx- Tx+