Displaying 20 results from an estimated 3000 matches similar to: "PRI"
2009 Feb 09
1
Noisy Ring Back Tone with TE205P card
Hi,
I am having problems with an Asterisk with a Digium TE205P card. The
issue is that the Ring Back Tone is noisy. I am making modem's calls and
this noise influences on the initial negotiation protocol, so modems
have to recall.
My configuration is:
Asterisk version: Asterisk 1.4.21.2
Linux version: CentOS release 5.2 (Final)
Card: Digium TE205P
2006 Mar 14
0
help required configuring card
Hii,
I've a Digium TE205P card and I'm running asterisk@home in a box.I want to configure this card in that box.But as it is a dual port card I'm not sure how to configure it in my box.By searching diffrent site I could able to make a sample configuration bellow I'm giving.Basically I want to connect one T1 connection in one port and in anather port of the card I'll
2010 Nov 02
0
Noise while passing channel using tde205p card
Hello,
I have an Asterisk box with a digium TDE205p card. The problem is that I
have several "Goto(s-${DIALSTATUS}" sentences and while the call is
trying to find a free channel to establish the call, I get a little
noise in each "Zap/... is proceeding passing it to Zap/..." line.
My configuration is:
Digium card: TE205P
Asterisk Version: 1.4.21.2
2006 Feb 19
1
[slackware 10.2 and TE205P] Unknown signalling method 'pri_cpe'
hi
after some testing with A@H, i've decided to install my asterisk
server on a slackware (because it's my favourite distro and it is
still suggested here
http://www.voip-info.org/wiki-Asterisk+Linux+Slackware)
, so, i've installed the last 10.2 release, and i've recompiled the
2.6.15.4 kernel.
then i've downloaded asterisk1.2.4 and zaptel1.2.4
i load module zaptel and
2009 Jan 28
1
E1 conection to a Cisco2600
Hi
I am trying to connect asterisk with a Cisco GW 2600 with E1 pri using a
Digium, Inc. Wildcard TE210P dual-span T1/E1/J1 card 3.3V (rev 02),
Errors:
[Jan 28 17:32:33] VERBOSE[6182] logger.c: == Primary D-Channel on span 1
up
[Jan 28 17:32:33] WARNING[6182] chan_dahdi.c: PRI Error on span 0: We think
we're the CPE, but they think they're the CPE too.
[Jan 28 17:32:34] NOTICE[6182]
2010 May 31
0
Dahdi PRI T1 Setup for TE210P
Hello,
I have been struggling with the configuration of this card on my box.
I have a T1 line and I am trying to setup asterisk with it.
I followed all the instructions and I still see a blinking red light on the
card.
I use fedora 12.
If everything is fine should I see a green line when I plug in the T1 line ?
I want to isolate the issue so I di not start asterisk. When I run asterisk
I get
2008 Nov 15
1
PBX -> PRI -> * -> Telco not working
Hello all.
I have an NEC PBX connected via a TE210p E1 line to an asterisk 1.6 box.
NEC -> E1 -> TE210P:1 -> * -> TE210P:2 -> E1 -> Telco
Incomming calls from the telco to the asterisk box to the NEC work fine with
indials and everything. Works sweet.
Outbound from the NEC to the Asterisk box fail. Giving an long dial tone
that then times out.
Ie, pick up NEC handset, dial
2009 Jan 30
0
Can't hear audio when Playback(something, noanswer) on Zap
Hi
I have this escenario:
|SIP or H323 phone|---->|Cisco2600|----E1-pri---->|Asterisk|------>IVR,
A2Billing, etc...
The problem is that I can not hear any audio when call from 'sip or H323
phone' and configure something like: exten =>
_01XXXXXXX,1,Playback(thank-you-for-calling|noanswer) ...
It works if I remove the 'noanswer' parameter but in this case it connects
2010 Jul 08
1
not sure what to change to point the timing to the at&t circuits?
# Span 1
span=1,1,0,esf,b8zs
bchan=1-23
dchan=24
echocanceller=mg2,1-23
# Span 2
span=2,2,0,esf,b8zs
bchan=25-47
dchan=48
echocanceller=mg2,25-47
# Span 3
span=3,3,0,esf,b8zs
bchan=49-71
dchan=72
echocanceller=mg2,49-71
# Span 4
span=4,4,0,esf,b8zs
bchan=73-95
dchan=96
echocanceller=mg2,73-95
# Global
loadzone = us
defaultzone = us
Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1"
2010 Apr 22
0
DAHDI User-User information "Message longer than it should be??"
Hi.
My configuration is Elastix 1.5.2-2 (asterisk 1.4.24, libpri-1.4.3-5,
dahdi-2.1.0.4-7 ) and OpenVox d210e connected to telco provider (Euro ISDN).
Here is my /etc/dahdi/system.conf:
# Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) HDB3/CCS ClockSource
span=1,1,0,ccs,hdb3
# termtype: te
bchan=1-15,17-31
dchan=16
echocanceller=oslec,1-15,17-31
# Span 2: TE2/0/2 "T2XXP
2007 Feb 28
7
Problem with TE212P
Hello.
I have a TE212 configured in E1 mode.
This is shown in a cat /proc/zaptel/2 and 3 (where the card is configured):
cat /proc/zaptel/2
Span 2: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" HDB3/CCS/CRC4 RED NOTOPEN
25 TE2/0/1/1 Clear
26 TE2/0/1/2 Clear
27 TE2/0/1/3 Clear
28 TE2/0/1/4 Clear
29 TE2/0/1/5 Clear
30 TE2/0/1/6 Clear
2011 Aug 16
1
PRI Problem
I am having a problem with a new PRI turn-up on dahdi 2.5.0 and
asterisk 1.8.5 that I have not seen before. The PRI is setup as B8ZS,
ESF and the span shows up and ok. This PRI is merely a crossover T1
going into an old DC0 class 5 switch.
I am getting the following errors over and over again
[Aug 16 10:26:10] NOTICE[8002]: chan_dahdi.c:3043
my_handle_dchan_exception: PRI got event: HDLC Bad FCS
2007 Jul 12
0
No subject
the Telco, I can make calls in.
What I am trying to get though is how to pass through the DID range.
The E1 that I am connecting to the Telco with, used to connect direct to the
NEC system and already has hunt group calling enabled for all 30 channels.
Also, I was given a 100 number indial range (from 00 -> 99).
If the E1 is connected to the NEC directly, I can call 5555 7320 and the NEC
2009 Jun 12
1
multiple PRI's in one group ..how??
Hello,
I was testing my asterisk for a while with 1.6 without much problem.
Now i am trying to install a new system with asterisk 1.4 but now i am
using a dual pri card instead of single pri.(TE220P)
What i want is to use both PRI ports as group.
Now i have zaptel.conf file created as follows
-------------------------zaptel.conf--------------------------
# Span 1: TE2/0/1 "T2XXP (PCI)
2013 Oct 31
2
issue with dahdi_channels.conf
Hello list
i have an issue with my dahdi_channels.conf
in span 1 when i use it like below i can do my outband calls without issue
; Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER)
group=0,11
context=from-pstn
switchtype = euroisdn
signalling = pri_cpe
channel => 17-31
context = default
group = 63
but when i add in channel 1-15 like: channel => 1-15,17-31
i receive all
2009 May 19
2
Unable to make outbound calls
I've got an asterisk 1.4.24 box with dahdi complete 2.1.0.3+2.1.0.2
I've got a 2 port T2XXP card attached with on T1 currently plugged in.
Inbound calls work fine, but outbound fail with the rather cryptic:
[May 19 17:28:07] WARNING[11360]: app_dial.c:1237 dial_exec_full: Unable to
create channel of type 'DAHDI' (cause 0 - Unknown)
There are similar threads I've found on the
2006 Apr 10
3
E1 PRI problem with TE205P
Hi all,
I've setup a PBX in production environment last week but we have immediatly
find out drop conversations and lot of errors (in asterisk logs) like:
Apr 10 17:30:48 NOTICE[25154] chan_zap.c: PRI got event: HDLC Bad
FCS (8) on Primary D-channel of span 2
My configuration is:
Motherboard: SuperMicro P8SCT (Intel E7221 chipset)
Hypertrading and APIC enabled
CPU: P4 3GHz
Digium TE205P
2012 Jan 23
1
Timing Slips CRC & E-Bit Errors - Asterisk - Trixbox 2.8.0.4
Hi,
I've searched and searched on the possible problems. If anyone can help me
that would be great.
Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) B8ZS/ESF
CRC4 error count: 4750
E-bit error count: 5023
Timing slips: 72
1 TE2/0/1/1 Clear (In use) (SWEC: MG2)
2 TE2/0/1/2 Clear (In use) (SWEC: MG2)
3 TE2/0/1/3 Clear (In
2006 Feb 16
1
Problem making outbound calls on TE210P using NFAS
Hello,
I'm running Asterisk@home 2.5
asterisk 1.2.4
zapatel 1.2.2
libpri 1.2.2
on a Dell Poweredge 2850 (1 CPU) with a TE210P
I have 2 t1 circuits using NFAS with dchan on 24 and no backup dchan. I am able to receive inbound
calls on all channels and can only make outbound calls on channels 25-48.
Attempting to make an outbound call on channels 1-23 results in congestion.
2012 Jan 03
1
ISDN E1, after electrical disconnected is not becoming UP, IRQ misses: 1
Dear All;
I am afraid from IRQ misses: 1
The ISDN E1 was working fine on the machine, the electrical disconnected and then the Red Allarm. I checked the dahdi and I found that I have to reinstall dahdi again and I did. But still not becoming UP.
The output of the cat /proc/dahdi/1 is following (I am afraid from the IRQ misses: 1, so if it is a problem what is the solution)?
[root at CC