similar to: Asterisk least cost routing expert needed

Can someone guide me on what package I can use to do least cost routing in asterisk-1.4 without going through the prepaid calling card platforms. I have tried Asterisk::LCR and LCDial without success, if more help on either too. I will be glad. I will be glad for good pointers. Thanks. Goksie

Hello, does anyone know of a good calling card solution for asterisk that is able to do lcr? Does astcc do this? I've been searching around and I can find some lcr modules/apps but none that incorporate prepaid card functionality. Regards, Igor H.

Hello Everyone, We are aware of a2billing and it's LCR functionality. I just wanted to know what other solutions you may be using. Maybe a tool that is a self contained module (ie a2billinig -> Asterisk -> LCR Tool -> Trunk). Is there such a tool? It should be open source as is all good software. Kind Regards, Nick Khamis

Greetings. I've been playing with the TrollPhone Rate Engine Addon for a week or so. I'm curious what is being used out there for LCR applications? I've run into a stump with the Rate Engine and that is the costing is done with an integer. With this, how do you put in say 0.014 / minute rate. And if your periods are not 60 seconds.. well.. then you have even more places to

Anyone using the rate_engine from TrollPhone? There is absolutly no documentation on how to setup data in the tables. If someone could send sample data, or post it to the wiki, it would be helpful. If any others are successfully using another Least Cost Routing method, please pass it along. THanks, Matthew

I've got two patterns I want to match on making an outgoing call... (one day - to do Least Cost Routing for Cell/Mobile calls) Firstly - I prefer '0' rather than '9' to get an outside line... Either its a call to a mobile No... (072 -or- 082 -or- 083 -or- 084) or its just another number to dial... I added the following... the playback just advises me which 'route' is

Maintainer: Express Line Date opened: January 17, 2006 Status: Open Value of bounty: $5000.00 Licensing for code: We retain intellectual rights to the underlying source code. We need Asterisk (stable version) to be able to perform a 2B channel transfer for a NI2 B8ZS PRI line. We can't use a channelized T1 at the time for our work. This feature is commonly called a call transfer on analog

Hello, We are glad to announce new release of our advanced billing and routing package for Asterisk - MOR v0.7 It is complete solution for VoIP billing and routing for advanced and start-up telecoms, carriers, voip calling card operators and ISPs. Demo available online, as LiveCD or as InstallCD. Contact us for more details. More info: http://www.kolmisoft.com What is new in

I forgot to pay this month's phone bill, and never noticed until family (the in-laws, who are too cheap to try the cell phone if landline fails, because it is 'more expensive') told me they were unable to reach us... As it turns out, the phone company disconnected us, but because Asterisk routes all outgoing calls in the Netherlands over VoipBuster, I never noticed anything! ;-) If

Since both UART driver codes on Allwinner A31, OMAP5 and x86 would use these definitions, we refactor the codes into a separated header to avoid unnecessary duplication. Signed-off-by: Chen Baozi <baozich@gmail.com> --- xen/drivers/char/ns16550.c | 71 +--------------------------- xen/include/xen/ns16550-uart.h | 104 +++++++++++++++++++++++++++++++++++++++++ 2 files changed, 105

Hello, I'm setting up a centos5 router for a friend. It will direct traffic to an internal webserver, already in place, as well as run squid proxy. It should do nat and have a firewall with iptables. I've set up routers before for this purpose but always of the bsd type and using their firewalls. I understand the concepts, nat, packet filtering, etc. but i'm not getting

Hello, I short question: I want to connect Asterisk to OpenBSC with mISDN, mISDNuser and LCR. Do I need chan_lcr? I have: Asterisk 1.8 mISDN .v2 integrated in Kernel 3.0.22 mISDNuser lcr 1.7 HFC-E1 Evaluation board from cologne chip I tried to configure Asterisk with <./configure --prefix=/usr/src/lcr --with-gsm-bs> and it runs without errors, But make and make install didn't run

Hello, I''m looking for some expert advice since I''m quite a newbie when it comes to programming. I realized that a lot of people(programs) are using the prototype.js and honestly, I cannot see why. Right, prototype has some nice AJAX support but it is lacking a documentation. I recently came accross cross-browser.com and saw their xlibrary - to me it seems that xlibrary

If this is the wrong list to post this on, my apologizes. I just figured it was the best place to find who I'm looking for. :) I need a Partner II expert. This involves integrating the Partner II with Asterisk. We have the Asterisk side setup, but are having trouble programming the Partner II to do what we need. We're willing to pay whatever your hourly rate is, and phone consultation is

Hello, There is a job requirement and I am posting it here : We would require a minimum of 4 years of experience with R. The position is in Mumbai, India and the employee needs to be based in Mumbai, India. Specifics : - The job title will be ``Data Scientist?. - As a data scientist one will be responsible for delivering analysis and insights on the order management process of a leading

Hello, There is a job requirement and I am posting it here : We would require a minimum of 4 years of experience with R. The position is in Mumbai, India and the employee needs to be based in Mumbai, India. Specifics : - The job title will be ``Data Scientist?. - As a data scientist one will be responsible for delivering analysis and insights on the order management process of a leading

Colleagues, We're in the process of standardizing on Sprint PCS and Cingular phones on a national basis (~ 50 properties, 1000's of lines). I manage an Asterisk install at one location. I've been looking at the Multitech CellFinder CDMA for Sprint as a dial backup solution. Basically, it's a CDMA to POTS gateway, tied to a PCS account. We would see it as a trunk line and I

Hi all, I am planning to implement LCR routing on my already running asterisk server. Uptill now i have found out that asterisk has no support for lcr, i have to do something about it myself, for example using the AGI. Im looking for ideas here. Whats the best way to start implementing lcr in asterisk. Should i use agi and start implementing my own lcr script or is there any plugin available which

I am not that good at regex and it's use in Asterisk. I am running Asterisk 1.4.13 Currently I have this in my extensions.conf for incoming calls on our house phone line: [housemenu] exten => s,1,GotoIF($["${CALLERID(num)}" = "815xxxxxxx"]?s|12); 815xxxxxxx is our home phone number, when caller id fails or is missing that is what is recorded. I want to expand this

My client is launching a new open source trouble ticket system. The system was written using Ruby on Rails and uses the latest rich web application features such as Ajax. They have no PR budget so we are looking for someone who can use their contacts in the software field to get writers to cover our product. Someone who has experience pitching bloggers would be a plus. This is a contract