similar to: misdn svn

Hi, I am struggling to get plain Cologne chip cards to run in NT mode, runs nice in TE mode despite the error message: login as: root root at 192.168.2.22's password: Last login: Tue Sep 1 23:09:24 2009 from 192.168.2.50 Welcome to Elastix ---------------------------------------------------- misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1

Hello, These are error messages I get when I try to call a number over CAPI channel. -- Executing SetCallerID("SIP/xlite1-3b80", "0") in new stack -- Executing Dial("SIP/xlite1-3b80", "CAPI/hfcpci/b17") in new stack > data = hfcpci/b17 > capi request for interface 'hfcpci' == hfcpci: Call CAPI/hfcpci/b17-1 (pres=0x00,

Hi, I have a Fedora 7 xen system with a domU to which I have delegated via pciback two isdn pci cards. One is a HFC-S card, the other a AVM Fritz!Card Pci 2.0. In the domU I load mISDN drivers for the cards. The two cards are recognized and function well UNTIL I either decide to unload one or both of the card driver modules (hfcpci and avmfritz) or I decide to shut down the domU. At this

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

Hello, I have some problems with mISDN. I can't send or receive call from the Billion ISDN card Mi configuration files are thoose: extensions.conf: [general] static=yes writeprotect=yes [SOME] exten => 101,1,Dial(SIP/101,30,Ttm) exten => 101,2,Hangup exten => 102,1,Dial(SIP/102,30,Ttm) exten => 102,2,Hangup include => outgoing [outgoing] exten

Hi All, We've got msidn configured: Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060) iend(0x8fd5060) and running on Asterisk 1.4.21.2: pbx*CLI> misdn show stacks BEGIN STACK_LIST: * Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0

I have set up a * box with two hfc ISDN pci cards using mISDN both in TE mode with PmP mode. (using $MODPROBE hfcpci protocol=0x2,0x2 layermask=0xf,0xf) I have no problem dialing out by explicitly naming the mISDN port, ex: Dial(mISND/1/${EXTEN},60) or Dial(mISDN/2/${EXTEN},60) But it does NOT work when specifying the mISDN group: exten => _(outpattern),1,Dial(mISDN/g:TEmode/${EXTEN},60)

Hi. I'm having problems with chan_mISDN configuration. Line "echotraining=yes" causes warning, when Asterisk is parsing misdn.conf and I'm confused why the PBX doesn't accept the setting. No matter which section I try to offer it, it is always invalid or out of range. The setting itself is supposed to be valid, it is in the sample configuration file of chan_mISDN 0.3.1.

HI, I tried to install asterisk and mISDN via http://www.asterisk.org/downloads/yum My machine is running with kernel-2.6.18-164.15.1.el5.i686 # grep kernel /var/log/yum.log Mar 21 16:09:28 Installed: kernel-2.6.18-164.15.1.el5.i686 Mar 21 16:09:42 Installed: kernel-devel-2.6.18-164.15.1.el5.i686 I've installed the following packages: # yum install asterisk16-misdn mISDN mISDNuser

Hello, I am having problems, getting my asterisk-domU to work properly. It consists of the following components: - Debian Etch under Xen-3.1 with a 2.6.18-kernel - Asterisk 1.2.24 - mISDN-1.1.5 I have 2 HFC-ISDN-cards, which I pass through to the Asterisk-DomU in permissive mode. This is working fine. The strange problem is, that the two HFC-ISDN-cards are not beeing initialized by the

Hi guys, I need to interconnect an asterisk server (1.4.17) with an alcatel pbx, because i want that an asterisk extension can call an alcatel extension and viceversa. I need to do this throug a NT port (of the digium card) for technical reasons (linked with alcatel hardware). Card installation was fine, but i'm not sure of the configuration i choose. In /etc/misdn-init.conf i put my

I'm running a setup with chan_misdn on a austrian PTP-line. When somebody dials in without an extension, he gets a busy signal. I don't see the call at all in asterisk. I *have* set immediate=yes in misdn.conf. And I *do* have an s-extension in my dialplan for the context used by misdn. Calls that provide an extension work fine. Attached is my misdn.conf and a verbose 3, misdn set debug

hello, i have a problem on started asterisk, when try to start asterisk a get the fowlling error: chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) Feb 17 11:34:01 WARNING[3104]: config_old.c:27 ast_load: ast_load is deprecated, use ast_config_load instead! == Parsing '/etc/asterisk/misdn.conf': Found Feb 17 11:34:01 WARNING[3104]: config_old.c:39 ast_destroy: ast_destroy

Hello all, I'm trying to conect two asterisk servers using two B410p Digium cards. One card on each server. I just setting up the first BRI port on server A as nt_ptp and the first BRI port on server B as te_ptp. I use an ethernet wire to connect the first port of server A (nt_ptp) with the first port on server B (te_ptp) but the port light cotinues blinking on red on both sides once the

I've just found my first problem. /dev/mISDN was being created with the wrong permissions... Thanks James > -----Original Message----- > From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users- > bounces@lists.digium.com] On Behalf Of David Phelan > Sent: Monday, 20 March 2006 12:18 > To: 'Asterisk Users Mailing List - Non-Commercial Discussion' >

Hello Armin, hello List I'm trying to get chan_capi working with asterisk from debian stable (asterisk 1.0.7, the debian version number is 1:1.0.7.dfsg.1-2). I managed to get it compiled by providing my own version of ast_copy_string. This is an Austrian PTP line. I can do outgoing calls fine (no comprehensive tests yet). For incoming calls, I'm getting "No answer" on the

Hi all, I'm fighting with a really strange problem that is really busting me. I have an asterisk 1.4.22 ( from a trixbox 2.6.2 ) and mISDN 1.1.7 3 extension on hardphone and 3 extension in softphone ( zoiper ) What happens is that sometimes the people on the other side of communication hear my voice as metallic and chopped. This happen either on incoming call than on outgoing call. If I

Hi All Has anyone experienced a crash specific to asterisk 1.2 and Centos 5 when using the misdn hfcpci module that comes with zaptel? I have an asterisk pack based on asterisk-1.2.17 that I have been using on dozens of machines that are rock solid and stable. Today when I tried moving it to Centos 5 I experienced a complete OS crash when calling over HFC misdn channels. Didn't really

Has anyone got chan_misdn working with passive BRI cards yet? I've tried both hfc (hfcpci.ko) and w6692 (w6692pci.ko) cards, but when I start asterisk I get the following when chan_misdn is loaded: [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) == Parsing '/etc/asterisk/misdn.conf': Found == Registered channel type 'mISDN' (This driver enables the

A plea to all! Has anyone had any success with two or more avm fritz pci cards with either misdn, chan_misdn, or chan_capi, and any version of linux 2.6.x? I have managed to get misdn to load under 2.6.13 and detect two cards using misdn-capi and chan-capi (using capiinfo and capi info under asterisk) - but the second card/controller doesn't answer or dial calls. But if I try misdn