similar to: Detecting Long PDD

Hi List, I have a 2Mbps SDSL link which gets saturated during peak time because about I have about 3 E1 worth of g729 traffic going thru. So I'm planning to use IAX2 trunking to reduce bandwith requirement and squeeze out each and every bit of this (expensive) bandwith. I've set up two boxes (debian etch), one in a remote data center (which has plenty of bandwith) and one behing

Hi List, Yesterday night after a power off due to a faulty UPS my asterisk doesn't want to start anymore. Here is what I get on the CLI: Asterisk Ready. *CLI> Disconnected from Asterisk server: Bad file descriptor. Executing last minute cleanups == Destroying musiconhold processes Asterisk uncleanly ending (0). I use 1.2.7 I think on a debian sarge and cdr_pgsql too. Any ideas?

Hi List, I am working on least cost routing code on the moment, and I am stumbling on a problem. Say you have provider A having: Prefix XXX 0.10 Prefix XXXYYY 0.20 And provider B having Prefix XXX 0.15 You're stuck, because you cannot decide if provider B's "XXX" prefix also covers XXXYYY numbers or not. If it doesn't, it would be a waste

Hi List, I am looking for a 1 FXO analog termination device, other than the obvious PC + FXO card, and which can achieve decent call quality. The SPA-3000 seems an option... have you got any other ideas? Cheers, Jean-Michel.

Hi List, Being very new to Xen I have a few generic questions for the list, I hope to grab some useful advice and pointers to documentation. I am evaluating Xen to consolidate a few existing servers into one appliance (mainly in order to reduce power consumption, heat, and hardware failure risks). I plan to have a SER router, an Asterisk LCR router, a voicemail server, a calling card server

Hello, I am trying to bootstrap a function that extracts the log-likelihood value and the nls coefficients from an nls object. I want to sample my dataset (pdd) with replacement and for each sampled dataset, I want to run nls and output the nls coefficients and the log-likelihood value. Code: x<-c(1,2,3,4,5,6,7,8,9,10) y<-c(10,11,12,15,19,23,26,28,28,30) pdd<-data.frame(x,y)

Hi List, Is there a way to tell asterisk to only accept SIP streams from the same IP address that is used for signaling? Thanks, Jean-Michel. -- Jean-Michel Hiver - http://ykoz.net/ D?couvrez la R?union des Technologies IP & Telecom TEL: +262 (0)262 55 03 98 - RCS 434 273 330 SAINT PIERRE

Hey guys. If my Asterisk box connects to the PSTN using SIP and IP over ethernet and doesn't require any authentication, what sort of a trunk would need to be created? Thanks, -- Nick e: nick.hoffman@altcall.com p: +61 7 5591 3588 f: +61 7 5591 6588 If you receive this email by mistake, please notify us and do not make any use of the email. We do not waive any privilege, confidentiality

RAD appear to have bucketloads of products which bridge between various interfaces (E1, BRI, POTS) and their own TDMoIP protocol. The attractive thing about them for me is their availability in Australia. The voip wiki says not much about it (http://www.voip-info.org/wiki/view/TDMoIP), and certainly nothing about if there is any way to get Asterisk to talk TDMoIP. Despite the name, TDMoIP

Hi List, I was wondering if anybody had tried running Asterisk inside virtualization software such as Xen. Are there known problems doing it? Cheers, Jean-Michel. -- Jean-Michel Hiver - http://ykoz.net/ D?couvrez la R?union des Technologies IP & Telecom TEL: +262 (0)262 55 03 98 - RCS 434 273 330 SAINT PIERRE

Hi, I need to have some SIP extentions on remote places where the latency from my asterisk box with public ip is 1~1.5 seconds. What codec will work fine on this sceneary? I'm planning to use iLBC, is a good choice? Regards, Guillermo.

We're getting our feet more and more wet with VOIP at work. We want to experiment with a good wireless (as in WiFi) phone. What would be a good phone to impress my boss with? I'm personally drooling over the UTStarcom F3000, but compatibility and shipping ETA info is a bit sketchy. Phil

Hi, I am using Asterisk 1.4.17 for my C4 routing but I am experiencing a high pdd of around 20 seconds. Could you please help me to reduce it and what could be the reason. Thanks Abid Saleem -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20110509/163192a7/attachment.htm>

Anyone got a way to pull the Source and Destination IP addresses for a call so they can be logged in a CDR and or CEL? Also anyone got a slick way for registring PDD on calls? Thanks Bryant -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20120213/7ef4ad08/attachment.htm>

Hi, understand that the bandwidth utilized for each call is dependent on the codec used, wonder if Asterisk can monitor the total bandwidth utilized and restrict/reject new calls when the resource is insufficient to support them reliably? Regards Andy Tan -- Andy Tan andytan@fastmail.fm -- http://www.fastmail.fm - Does exactly what it says on the tin

I have a _very_ specific situation where I need queues to work in a very specific manner - I need the queue to only accept one call at a time, even though several phones are attached to it. My memory tells me that queues might have even worked this way in the distant past (pre 1.0)...but I am willing to be mistaken. Is this even remotely possible? PaulH

Can anyone point me to a reference or sample config for bypassing a nailed up (point to point) t1 between two PBXs with asterisk and a pair of t1 cards? Right now I have 2 Nortel norstars connected to each other via a leased line t1. I also have a solid 10mbps low latency microwave link between the 2 sites. My goal is to run an asterisk box at each end with a t1 card and Ethernet card to

I have been discussing an asterisk solution with a company that has a custom written dialogic based solution. The issue is that their dialogic solution can read callerid from incoming calls, even if the callerid is blocked. I have read before that Asterisk can do this, and they want me to make sure that their new system will be able to do this. A quick poke around inside the zaptel source code

Hello all, Just a question, on asterisk box : I looking on the web , for asterisk at large , and 'asterisk future of telephonie' ... If we would like to change our OLD PABX 600 phone with 4 E1, to install a asterisk with full ip phone in SIP, Could we use 1 Box for asterisk with voicemail, zap channels and some agi script ? thanks Fabrice

Hi All, I have a SIP provider that tells me that my RTP stream uses a "20bytes payload in the g729 coded data". And they would like that we change this to 30bytes (3 frames). But maybe I'm wrong but isn't a certain payload just a standard for a codec ? And if I'm wrong, how can I change the payload for my g729 calls in Asterisk. Greetings, Attilla