similar to: call file result

Hi, I have this setup: (PSTN E1 PRI) -- Asterisk -- (crosscable) -- Alcatel PBX --- analog phones and a few of VoIP phones directly connected to Asterisk. Calling a number (only one until now!) - an automatic responder (IVR) - from VoIP phones works, from analog phones doesn't work: NOANSWER after a few seconds. I'm using no 'r' in dial options (this caused a problem with an IVR

Hi Guys, i spent some time to figure this out (since i love how dialplan is written) but i decided to ask for your help guys. i have two asterisk servers one is 1.2 the other is 1.4, from 1.4 (pbx1) to 1.2 (pbx2) i can leave a voice mail without any pb, but from pbx2 to pbx1 it just hang up. in pbx2 extensions.conf: i am using: exten => 8029,1,Dial(IAX2/pbx1/${EXTEN},20,tTWwr) in pbx1, i

Hi. I'm dialling two numbers - one that's unobtainable, one that's busy. ${DIALSTATUS} is coming back ANSWER each time right before the channels hang up. Am using the following dialplan macro to dial out. [macro-advdial] exten => s,1,Dial(${ARG1},20,g) ; Ring the interface, 20 seconds maximum exten => s,2,Goto(s-${DIALSTATUS},1) ; Jump based on status

Hi, I'm trying to write a small Visual Basic app to throw a popup with CallerIDNum when a call center agent answers a queue call. Does anyone know what is the right manager event to intercept? Thanks Mimmus

I have an issue where a particular dialplan works but another doesn't. I'm not sure why. To me they look identical and it has me stumped. This works: [to-test] exten => _X., 1, SetCallerPres(allowed) exten => _X., 2, Monitor(wav,/tmp/test-${UNIQUEID},mb) exten => _X., 3, Ringing exten => _X., 4, Dial(SIP/9330 at a-test,20,ro) exten => _X., 5,

Hi, I'm trying to implement dynamic routing of incoming calls to local extension if previous outgoing call was unanswered. But after I do Goto to s-NOANSWER, variable ${EXTEN} changes to 's-NOANSWER'. I guess this is normal, but I don't understand why ? How to workaround on this one ? Thanks in advance, regards, Rob. [outbound-capi-ISDN] exten => _0.,1,NoOp(Calling ISDN

Hi, I am looking at http://www.theschmandts.org/blog/?p=28 to setup missed call notification but i am having issue. following is my dialplan [macro-stdexten] exten => s,1,Dial(${ARG2}) exten => s,2,Goto(s-${DIALSTATUS},1) ; Jump based on status (NOANSWER,BUSY,CHANUNAVAIL,CONGESTION,ANSWER) exten => s-NOANSWER,1,Voicemail(${ARG1},u) ; If

Hi All, I'd just like to verify what the correct operation of the timeout parameter is for the dial application. I'm not sure if I've encountered a bug or a configuration issue. When a sip phone is not responding to invites on an outbound call, the dial application still waits the duration of timeout before continuing with dialplan execution. I was under the impression that app_dial

Hi All, i want to configure voice mail on Asterisk 1.4 for multiple users. let me explain you the scenario. i have 10 users with the name of 1000,2000,3000,4000,5000,6000,.......and these user can call to each other. Now i want to configure separate voice mail box for separate user. my extensions.conf ..... settings below.. [voicemail] exten => _X.,1,Dial(SIP/${EXTEN}) exten =>

Hi, I am facing some issues while using MixMonitor and StopMonitor. My extensions logic is attached below: exten => s,1,MixMonitor(${CALLERID(num)}_${TIMESTAMP}.gsm,b) exten => s,2,Dial(SIP/101,13) exten => s,3,StopMonitor() exten => s,4,NoOp(Dial Status: ${DIALSTATUS}) exten => s,5,Goto(sss-${DIALSTATUS},1) exten => sss-NOANSWER,1,VoiceMail(777 at salesvoice) exten =>

Hi! Trying to figure out what I am doing wrong... 1 std SIP phone (0317998975) registered to an Asterisk (SVN-trunk-r234256) 1 Cell phone 00733025975 attached through H323. extensions.conf exten => 975,1,Goto(975-${DEVICE_STATE(SIP/0317998975)},1) exten => 975-INUSE,1,VoiceMail(0317998975 at inputinterior.se,bs) exten => 975-INUSE,2,Hangup() exten =>

Hi all, I am trying to understand how I can get a simple IVR scenario to work properly (having already removed most of my hair...). The basic requirement is as follows: * Caller arrives at our main number * Caller is greeted and then told they can enter an extension number, if known, or wait and their call will be connected to an available rep. * The IVR then dials a group of extensions (if

Hi, calling a partner on the other side of a SIP trunk, call gets disconnected immediately after answer. This is the content of log file: Jun 14 16:25:14 DEBUG[14380] channel.c: Didn't get a frame from channel: SIP/cerved-out-6eba Jun 14 16:25:14 DEBUG[14380] channel.c: Bridge stops bridging channels SIP/232-2e41 and SIP/cerved-out-6eba Jun 14 16:25:14 DEBUG[14380] channel.c: Hanging up

I was wondering if it is possible (in 1.2.x) to get the SIP response code back after doing Dial(). Dial() seems to treat most call-setup problems as dialstatus CONGESTION, and some are NOANSWER, but I want to know the SIP response code, so I could return the right tones to the user, not just a congestion tone for every fault. Anyone know a way to find out that information, so I want the

Asterisk isn't playing my voicemail greetings even though they are defined. Below are the relevant configs(from show dialplan) as well as the level 3 verbose messages asterisk is giving. Also a listing of the directory. Asterisk just plays the "The person at extension..." message, not the greetings I have recorded. Thanks -- asterisk*CLI> show dialplan macro-stdexten [

Dear All, I can not transfer call in progress. What's wrong with my macro? I think tT flags is enough right? [macro-stdexten] exten => s,1,Set(temp=${DB(CFU/${ARG1})}) ; Get CFU key exten => s,2,Set(DNDStatus=${DB(DND/${ARG1})}) ; Get DND key exten => s,3,GotoIf($["${temp}" = ""]?5) ; If not existing, goto priority 5 exten =>

I thought it was quite easy to implement but I cannot get one-touch recording to work. Here are the changes what I did: I restarted Asterisk after the change (because reload does not work for changes in features.conf). I press *1 on the Polycom IP600 phone to record a conversation but no new wav file appear in /var/spool/asterisk/monitor or elsewhere. Any suggestions? Here is the console log:

Hi, at my Asterisk box, I have a few of IAX2 phones (configured with alaw/ulaw/gsm codecs, in this order) and a PRI E1 line. In iax.conf I hav: disallow=all allow=alaw allow=ulaw allow=gsm During some incoming call, I read at console: -- Executing Dial("Zap/2-1", "IAX2/215|20|TtwW") in new stack -- Called 215 -- Call accepted by 10.97.1.7 (format ulaw) --

Hi, BRIEF RESUME: Is there any other way to obtain the same result but being easier to configure?? Thanks! EXTENDED RESUME: i've configured a, rather difficult, macro that even for me without being documented is difficult. I ask for the help of the experts to know if the functionality it apports can be achieved better in another way. What i'm trying is to enable call a channel (e.g.

Hello, We have a strange situation (asterisk 1.6.2.14), where we get a result for DIALSTATUS for BUSY and No-ANSWER, but nothing for CANCEL. This is the (relevant) test dialplan: -------------------------------- [incoming-private] exten => _X., n, Dial(SIP/1001,30) exten => _X., n, NoOp(${DIALSTATUS}) exten => _X., n, Gosub(incoming-status,s-${DIALSTATUS},1) [incoming-status] exten