similar to: Cisco 801 and rcapi

Hello. It seems very very strange to me that nobody talks about connecting ISDN lines to asterisk using a device with RCAPI Support. There are some devices (most of them isdn routers, like the famous Cisco 800 family) that support this protocol. It basically is an ISDN to IP gateway. There used to be software that used this technology to send and receive faxes, act as voicemail and even ISDN

I own a ME600 EPIA Mini-ITX main board with the latest Debian distro (kernel 2.6.8) with isdnutils-base, libcapi20-dev, libcapi20-2, isdnactivecards installed. I have a QuadBRI module by Junghanns with bristuff-0.2.0-RC3a (with asterisk-1.0.3, zaptel-1.0.3 and libpri-1.0.3), and chan_capi-0.3.5. I followed all INSTALL instructions, but I have some strange behaviour. All modules seems to be

Hi all, i'm tryinf to install chan_capi but i get this error root@obelix:/usr/src/chan_capi-0.3.5# make gcc -pipe -Wall -Wmissing-prototypes -Wmissing-declarations -g -I/usr/include -D_REENTRANT -D_GNU_SOURCE -O6 -march=i586 -DNEVER_EVER_EARLY_B3_CONNECTS -DCAPI_ES -DCAPI_GAIN -DDEFLECT_ON_CIRCUITBUSY -DCAPI_SYNC -DUNSTABLE_CVS -Wno-missing-prototypes -Wno-missing-declarations -DCRYPTO

Hi! I have some (short) question about the Eicon DIVA (V-)4BRI cards I want to have (short) answered before buying the DIVA card. I know there are several Eicon guys active on the list, thus I ask on the list instead of directly to Eicon so that all other will benefit as well. 1. Do Eicon DIVA (V-)4BRI cards support TE and NT mode? 2. Can the clock (master/slave) be configured independent

I'm trying to compile chan_capi-0.5.4 on Slackware 10, but I have bunch of errors. (By the way, can I use chan_capi for ISDN card with winbond w6692cf chipset?) I'm not a linux expert, still :-) Before compiling, when I type "modprobe capi" to load capi module, and then "lsmod", i get list of modules: capi 6208 0 kernelcapi 30496 1

Hello, I have problem with capi, I can't install it. I have putted all info what I did and what I get :). I think you can suggest me how to solve this problem.and thanking you in anticipation. I have ISDN Frtiz!Card PCI v2.1and I want to install it to my ubuntu box (kernel: 2.6.17-10-server). Using command "lspci -vv" , I can see that kernel finds this card: *02:0d.0 Network

I've got a brand new Eicon Diva Server BRI card and I want to configure it with Asterisk. I managed to get asterisk and zaptel to compile and install, I've compiled and installed the drivers for the Diva card and now I need to compile and install the chan_driver for chan_capi. Unfortunately this fails miserably. I get the following messages: I'm using: Kernel 2.6.16.37.4,

Hallo wine-users, I'm new to wine and to this list. During configuration I got the message that libcapi20 could not be found. I did not worry about that, thinking it was an ISDN thing and I don't use ISDN. But now I have to run a Windows application which insists on using libcapi20 :( I have been searching with Google, but not been able to find any sources for it. Could somebody please

I had unexpected hangups from my asterix box using the i4l driver. (SIP <-> SIP calls worked execellent, but SIP<->ISDN didn't.) Then I changed the i4l driver in modem.conf with the chan_capi from jungham. (http://www.junghanns.net/asterisk) I followed his instructions in the INSTALL file, and first encountered some errors compiling it. It help by deinstalling several

Hi all, I compiled/installed chan_capi.so without problems. When I launch Asterisk, I get the following error: --- [chan_capi.so] => (Common ISDN API for Asterisk) == Parsing '/etc/asterisk/capi.conf': Found Mar 30 19:47:52 NOTICE[16384]: chan_capi.c:2338 mkif: ast_capi_pvt(91xxxxxx,*,pstn,0x2,2) (1,2,64) (0)(0.800000/0.800000) 0 Mar 30 19:47:52 NOTICE[16384]: chan_capi.c:2338

Hi all, * was running ... I have a WT405P and an AVM C4 with chan_capi 0.3.4a Today chan_capi stopped working, without any changings at the system. It seems, that not * is the reason, because isdn-log also shows no calls. If I try to call * from outside via capi, I only get a busy. That is the try from inside to outside: stern01*CLI> -- data = @89930:0107901723168212 -- capi

Hello, list a have a problem i can start asterisk, i get the fowlling error: [chan_capi.so] => (Common ISDN API for Asterisk) == Parsing '/etc/asterisk/capi.conf': Found Feb 11 13:50:36 NOTICE[2535]: chan_capi.c:2636 load_module: CAPI not installed! Feb 11 13:50:36 WARNING[2535]: loader.c:345 ast_load_resource: chan_capi.so: load_module failed, returning -1 Feb 11 13:50:36

hi all, i have a probably very stupid question/problem. for testing purpose i am trying to get asterisk running with two isdn cards. I'd only like to here the demo sound when i call the number - but nothing works. The output of show channels is not showing any channel - should there be 4 channels ? - capi info shows my two cards perfectly. The ISDN Controller's are attached to an PTMP

Hi to all I've mada up my mind and i tried to change from i4l to chan_capi, following some councelling from the gurus. I compiled it up, and when i try to load it in modules.conf, i get that wonderful message and Asterisk does not start: [chan_capi.so]Feb 17 09:21:40 WARNING[16384]: loader.c:239 ast_load_resource: /usr/lib/asterisk/modules/chan_capi.so: undefined symbol: ast_get_group Feb

Hallo, I recently installed wine 1.1.2 on my SlackWare 12.1 Linux system, because I have to run a hardware debugging program which only runs under Windows. When I run the application, i get the message "CAPI 2.0 not installed". In the same directory as the application there's a file called capi2032.dll, and I suspect that has something to do with it. If so, how do I tell wine that

Hello, While upgrading * from 1.0.9 to 1.2.5, I have installed chan-capi-head and I can't start asterisk under asterisk group "asterisk -vvvvgc -U asterisk " and "asterisk -vvvvgc -U asterisk -G dialout" work well but "asterisk -vvvvgc -U asterisk -G asterisk" fail. I am thinking about a group permission configuration but I have exactly the same one

Dear list, I tried to install the CAPI support RPM from the SUSE 9.2 disks. YaST tells me it is happy with the process. The Asterisk release I am using is the one that comes packaged in RPM format, also included in the distribution. Still starting asterisk with the usual asterisk -vvvc I see that something goes wrong. [app_capiCD.so]Dec 23 19:21:45 WARNING[1076850816]: loader.c:242

Hello all I found a bug in the chan_capi driver (really a not implemented message handling and then a false error condition) and I guess I have wrote a patch to fix it (basically I searched the internet for other capi open source implementation an borrowed the code snippet) but I don't know where to send the report and bugfix. I also found some miss-behaviours that I would like to share

Hi there, I searched in mailinglist and in web, but no answer to my problem... Only this post with no answers: http://lists.digium.com/pipermail/asterisk-users/2004-March/038994.html I'm using CVS Asterisk (05/17/04) with chan_capi 0.3.1. (multiple controller support). In my Asterisk-box there are 2 Fritzcards (module for second card compiled with changes on sourcecode found in the web).

Hi everybody. I'm trying to setting up a V4 BRI EICON card on ASTERISK 1.0.7 My linux is a debian. It was working during a few days an suddenly (after a lot of reboot) I've got this error message that seems to be very popular but I couldn't find any answer on the net : ==============================================. Asterisk Dynamic Loader Starting: == Parsing