similar to: Looping Problem With Call Forwards - Do you have comments on my solution?

Hi List I need a quality US 800 DID over IAX for my Asterisk server, preferably one that doesn't cost the earth. Any suggestions please? Thanks -- Chris Blunt Entropy IT Ltd -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061220/4919f3cb/attachment.htm

Apologies if I am not understanding something about how things are being handled when using S4 methods, but I have been unable to find an answer to my problem for some time now. Briefly, I am associating the generic '[' with a class which I wrote (here: myExample). The underlying back-end allows me to read contiguous slabs, e.g., 1:10, but not c(1, 10). I want to shield the user from this

Howdy, How can you tell if RTP traffic has been reinvited/is bypassing an * server? Sincerely, Brent A. Torrenga brent.torrenga@torrenga.com Torrenga Engineering, Inc. 907 Ridge Road Munster, Indiana 46321-1771 +1 219 836 8918 x325 Voice +1 219 836 1138 Facsimile www.torrenga.com

Dearest List, I guess I missed this point: Is it true that if you change the echo canceler in zconfig.h, and then recompile/install your zap modules, that for this to be taken into effect by * you must then recompile/install *? I would have figured that the zap echo cancellation method was independent of *, and I don't recall seeing any docs mentioning either way. Sincerely, Brent A.

Is it possible to dial more than one extension with a different CID to each extension? I'm thinking macros might be needed, but I don't have a good handle on macros. Is it possible? Any hints? BTW - this would be used for showing an internal extension to one phone and a PSTN accessible number to another phone. Sincerely, Brent A. Torrenga Torrenga Engineering, Inc. 907 Ridge Road

Howdy: Does echo only occur on analogue PSTN lines, or can it also occur on PRI and BRI lines? If so, for the same reasons? This is a part of our consideration to transition to BRI. Sincerely, Brent A. Torrenga brent.torrenga@torrenga.com Torrenga Engineering, Inc. 907 Ridge Road Munster, Indiana 46321-1771 219.836.8918x325 Voice 219.836.1138 Facsimile www.torrenga.com

I am thinking of turning on the NAT option in our Cisco phones (and the corresponding sip.conf modification) to allow the phones to be taken outside the LAN. Can anyone think of any reason not to just always turn on the NAT enabled option? I can't think of a reason not to always operate these phones with this enabled, since it would likely allow them to be taken outside our LAN and used.

Hola, What would a valid regexp in Asterisk be to identify a NANP number, i.e., NXXNXXXXXX? Sincerely, Brent A. Torrenga Torrenga Engineering, Inc. 907 Ridge Road Munster, Indiana 46321-1771 tel:+1 219 836 8918 x325 fax:+1 219 836 1138 email:brent.torrenga at torrenga.com web:www.torrenga.com

Boy oh boy. This blows. I upgraded to 1.2.2 from 1.0.9, and of course had the timebomb bug. Immediately after upgrading to 1.2.3 we were ok, for 24 hours or so. Since upgrading to 1.2.3, though, the whole system has locked up twice. Once on Thursday, and then about a half hour ago. The server would reply to a ping, but no ssh login, no local console login - just locked up. This ain't good for

I think A@Home allows a user to search a directory by either first OR last name, right? I don't know for sure since I don't run A@Home. I would like to offer that functionality in my system - and I'd have done it by now if there was a prompt where Allison asks "press 1 to search by first name, press 2 to search by last name". But I don't think that prompt exists. Can

Has anyone had problems getting their preffered codecs on the Teliax web interface taking effect? I have two accounts, two separate yet similarly configured * servers. On one account the settings took right away - on another server I am getting no result. In fact, no matter what I change the settings to, only the old codecs are usable (otherwise * says it can't negotiate a codec). Teliax

Out internet connection was out this morning. It seems that the SIP extensions on our LAN were affected. Behavior like: Call comes in over POTS to a TDM400P, there is a delay then before the Cisco 79[46]0's start to ring. If we were lucky enough to get a call through, then we could not transfer the call, or place the call on hold, or park the call. Outbound calls seemed to have a delay

I have one use on our PBX who has been experiencing seemingly random disconnects. The user is on the same LAN as everyone else, using the same type of phone (79XX loaded with SIP firmware) as everyone else. He had some disconnects a few weeks ago, I suspected the phone, so I swapped his with mine. I have since not had issues with his old phone, however, he has had issues using mine. So, the

We are looking to lose the TDM400P in favor of an ISDN-BRI solution. This should get rid of static on the line (at least any static generated by our half of the circuit), right? I am a total virgin to ISDN. I understand that we need two BRI circuits to provide four voice channels, and that the hardware to speak to the BRI circuits can be passive or active, with the active type being much more

Well, I thought and hoped my issue of random hangups on our TDM400P were related to busydetect=yes in zapata.conf. The behavior of a call being hungup has not changed, however, since setting the busydetect option to 'no'. Again, the only affected user is my loud talker... What are some causes/solutions to seemingly random call disconnects on Zap channels that people have seen? I have

Dear list (and more specifically Bret), I am getting one-way (inbound only) audio when trying to place a SIP call via voip.trxtel.com (i.e. 18005558355@voip.trxtel.com). The Cli spits out "== Forcing Marker bit, because SSRC has changed" 5 times after atempting a native bridge. I realize this is most certainly a NAT issue, the * server is behind one. Sip.conf has externip=, and

Hi folks, Just a quick question. Does the GrandStream GXP-2000 phone support presence (hints)? Cheers, Richard. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060109/26c4a63c/attachment.htm

Dollars to donuts it is related to these two posts, but no one seems to know where or why it happens - this issue doesn't seem to be related to one specific piece of hardware: Post 1) ********************************************************* Anyone ever seen MeetMe cause * to crash? Specifically, it happens consistantly if someone begins to enter a conference and then decides to hangup while

Hi all, Anyone using their services ? I'm thinking of setting up my servers with their service. But before starting to mess with my extensions.conf I thought "let's check the community for their experience". Thanks, Michiel van Baak.

Sipdiscount has replaced their asterisk servers for another thing. Then, no more iax. Ok, but I can't make calls using sip also... I'm getting a "forbidden" error when using sip1.sipdiscount.com. Anybody got it working? -- Alejandro Vargas