similar to: Uniden UIP200 Issues

Hi, all. I've got my Uniden UIP200 configured via TFTP (had to get DHCP 3.0.1 -- Debian's latest is 2.0.x!), and all seems well... except for the minor detail that it doesn't work. It registers fine with Asterisk, but when I copied my Grandstream's sip.conf info and plugged in the Uniden stuff, no dice. Any ideas? Thanks... -Ken unidencom.txt: OverwriteLocalSettings

Anyone using the UIP200 with *? I am having difficulty getting the phone to register and *stay* registered for more than 4 seconds. The * console shows the UIP200 registering and records the user agent. The UIP200 displays station name and time on its LCD, then 4 seconds pass and it shows #1 DISCONNECTED. The * console reports no problem and believes the device to still be registered. A call

I got a Uniden UIP200 and started to configure it and I am lost.... I have a tftp server setup on my * server and have the files unidencom.txt and uniden<mac>.txt there. But it doesn't quite work yet. It registers as a sip phone (sip show peers), but I cann't dial it and the display shows #1 disconnected all the time. It has firmware version BS4.59a in it. I have no idea if I

hello, yesterday the uniden uip200 phone was recommended to someone. i am looking for an alternative to grandstream bt-100 because i can not do a supervised tranfer with it. here my questions: 1) does the uip200 support supervised transfers? 2) can i buy the phones in europe, especially in germany? thanks in advance, jan goericke

I'm looking at the Sayson 480i or the Cisco CP-7960. Which one would you suggest and why please ? Best Regards, Alex Brecher Visit us at http://www.Successfulhosting.com <http://www.successfulhosting.com/> -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20041128/8e282c51/attachment.htm

Hi all, I curious to know if other UIP200 users have this same issue: You flash (XFER button) to consult-transfer a caller to another extension. If the transfer target party is unavailable (ie: voicemail), there appears to be no way to get the original caller back. If it's a known limitation, has anyone come up with a functional work around? Thank -- ..................................

Hi, all. Got my Uniden UIP200 today (ordered from thetwistergroup.com), and was very excited to set it up... until I came to the realization that there were no docs with it whatsoever. There was, however, a sheet of paper with the stock warnings (don't use the phone in the tub, etc.), AND a URL -- for documentation. Score! Well, no. The URL it gave me, bcs.uniden.com, does indeed have

I am trying to get a new Asterisk installation running using a Zultys ZIP2 phone and a Uniden 200 phone. I have the system working reasonably well (although probably not optimal) except for a couple of items. First, I can't get the voice mail message light to work on the Zultys phone but it works just fine on the Uniden phone. Second, the time presented on the Uniden UIP200 phone is 1 hour

Hi, I've read through the archives, and wanted to get an updated opinion on the Uniden UIP200 phone. Seems like there were a lot of opinions that it was a good phone, but there were a few items that people were waiting for firmware updates for, but that was in 2004. I'm going to be using them in an office, 12 phones, on a LAN connected to an asterisk box. Thanks for any advice or

I just spent the last hour or so trying to get this firmware to work across a NAT with no success. I have a GS BT101 working through the same NAT, so I don't think it's the NAT itself. I have a STUN setup in * and pointed the UIP200 to it and I tryed several combinations of nat= in the sip.conf and in the config files for this phone. No luck(yes, I did a reload now with each change in

I guess this is an FYI Running NMAP (protocol detection, common ports) against my UIP200's causes them to reboot. firmware BS4.56. Be careful where you point that thing. -Nate

Hi, We've recently deployed 6 Uniden UIP200 phones (running firmware 4.54). We've been having some serious problems: 1) All the phones randomly reboot themselves. Typically when trying to answer or initiate a call. 2) All the phones will disconnect from a calls with the PSTN after 2-3 minutes. 3) The phones are unable to interact with a remote IVR (digit presses are not received at

I am trying to get distinctive ringing going again with these phones, depending on the outside line the call comes in on. I had a working 1.0.x Asterisk setup using: SetVar(ALERT_INFO=<http://127.0.0.1/Bellcore-dr2>) Which used the short quick rings. In Asterisk 1.4, I have tried several things, but I think the correct syntax is: Set(_ALERT_INFO=<http://127.0.0.1/Bellcore-dr2>) But

Hello Everyone, My company is about to deploy * as replacement for our existing commercial Altigen PBX. Meanwhile, I've been trying to find the best cost effective SIP VoIP phone which we can use in office for 20-30 employees, as well as a few remote staff. Normally I wouldn't post about a VoIP phone, however, this phone was released less than a week so I thought I'd give some

Hello We recently moved to Asterisk 1.2.4 (from 1.0.x) and our 10 Uniden UIP200 have stopped working ever since. We can make a call with the UIP200 to any other extensions, but it can not receive a call. In fact the UIP200 always appears offline: It does show up in asterisk a few seconds after the UIP200 reboot: -- Saved useragent "Uniden SIP Phone p2 Ver BS4.70" for peer uip200 but

Hello Everyone, My company is about to deploy * as replacement for our existing commercial Altigen PBX. Meanwhile, I've been trying to find the best cost effective SIP VoIP phone which we can use in office for 20-30 employees, as well as a few remote staff. Normally I wouldn't post about a VoIP phone, however, this phone was released less than a week so I thought I'd give some

I'm trying to think of a way to store/represent the Asterisk .conf files. One method is to store them in MySQL in some format, and then write some scripts to query MySQL and generate the conf files before doing a reload. MySQL is pretty heavy handed though. I'm looking for something a bit more lightweight, maybe.... some sort of XML based database for Linux, where the config files could

Hello all, The "Secret Agent" final release of the Asterisk Management Portal is now available for download: http://amp.coalescentsystems.ca/ This exciting new release adds a great deal of functionality and flexibility. Thank you for all the contributions and feedback! 1.10.007 - Added AMP Users (multi-department, basic multi-tenant) - Added incremental upgrade script

does anyone know of a 2.4 or 5 ghz cordless phone system that has an ip base station? thanks

Hello all, Uncertain if I have a configuration problem or a buggy phone, I'm requesting that Uniden uip200 users attempt the following and share their results: - dial into voicemailmain - press 2 to change folders - listen to each of the folder prompts. Is the audio for the folder number clipped at the beginning? This audio clipping problem will also appear in other applications, such as