Displaying 20 results from an estimated 2000 matches similar to: "Bizarre Echo Problem"
2004 Sep 09
4
IAX2 dropping call?
Hello all,
I updated from CVS 3 days ago and now my IAX2 gateway is dropping
calls without warning.
It happens right in the middle of a conversation with no pattern. I
never had this
Problem before and am usually talking 2-3 hours a day.
Is their a bug? Should I rollback?
Cheers,
Paul Seniuk
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Paul
2005 Aug 05
3
Is this echo problem down to IP Phone hardware?
Hello
I have a Grandstream GXP2000 with latest firmware. When I use it holding the handpiece I don't hear any echo - neither does other end. However, if I use it handsfree, the other end notices echo when they speak - ie their voice is echoy. I hear their voice being a bit echoy.
Is this purely down to the IP Phone? Is there anything I can do about it? I considered buying a more
2009 Oct 22
1
Poor VoIP voice quality in one direction from three providers
We currently use asterisk 1.4.x with two Zaptel cards connected to POTS
lines. So we make "outbound" calls from their softphones (using ulaw
format), which go over a dedicated DSL line to the asterisk server in
our office, which then converts the calls to POTS.
This all works fine, assuming there aren't any unusual problems. It
sounds as good as POTS on both ends.
However, we
2005 Mar 22
1
Is there a way to get inserted into an LEC's CLIDB?
> -----Original Message-----
> From: Robert Goodyear [mailto:me@jrob.net]
> Sent: Tuesday, March 22, 2005 1:21 PM
> To: Asterisk Users Mailing List - Non-Commercial Discussion
> Subject: [Asterisk-Users] Is there a way to get inserted into an LEC's
> CLIDB?
>
>
> Does anyone know if there's a service out there to -- for a fee --
> inject our DID into the
2004 Sep 07
2
Maximum tollerable lag/jitter for IAX2 w/o j itterbuffer enabled?
Unfortunatly no on both counts.
The arrangement right now has:
PSTN Trunks & Stations <-> Nortel Norstar#1 <-CT1-> Asterisk#1 <-IAX2->
Asterisk#2 <-CT1-> Nortel Nortstar#2 <-> Stations
The Asterisk boxes provide Voicemail to their sites Norstars and intersite
calls over IAX. Local Voicemail works flawlessly at each site but there have
been reports of PSTN calls
2004 Aug 19
6
How to run different codecs between the same endpoints on an IAX trunk?
Or perhaps how to configure and refer to two parallel IAX trunks with
different codecs?
I have a situation where I'm using G.729A as my IAX trunking codec. Now I
need to push some short duration, low bitrate modem traffic over the link (a
credit card terminal). Obviously the modem audio isn't going to survive the
G.729 codec process intact, so for the times the device is used I'd like
2004 Sep 07
4
Maximum tollerable lag/jitter for IAX2 w/oji tterbuffer enabled?
> -----Original Message-----
> From: Chris Shaw [mailto:chriss@watertech.com]
> Sent: September 7, 2004 4:40 PM
> To: Asterisk Users Mailing List - Non-Commercial Discussion
> Subject: Re: [Asterisk-Users] Maximum tollerable lag/jitter for IAX2
> w/ojitterbuffer enabled?
>
{clip}
>
> If you can reproduce it, this smells like a bug... IAX runs over TCP and
TCP
>
2005 Oct 11
6
PRI echo issues: solvable?
Hello,
After solving the other "low hanging fruit" audio issues in our Asterisk
PBX, we are left with occasional cases of severe echo which we have not
found a solution for yet.
Our system:
- Asterisk 1.2.0-beta1
- TE110P on a PRI
- TDM04 and TDM40, but these are unrelated to current echo issues
- Fedora core 3
- Echo canceller KB1
Most calls have minimal, acceptable echo levels. But
2010 May 09
2
Re TrixBox
Hey Guys
We are replacing a BM4 with a trixbox (asterisk) virtual numbers as the
customer wants to move the callcentre.
They are asking for an equiv to the ipview
I gather HUD may be or the panel view
The problem is that we need to see
(a) total calls in the queue
(b) calls for specific DID - How can you give 1 DID preference to another
DID
ie
DID 61740410001 = Fred Electrical
DID
2004 Sep 02
5
Any way to _always_ execute certain commands in a dialplan context?
I've got a need to do something like the following:
[foo-context]
exten => _.,1,SetCIDNum(123)
exten => _.,2,SetCIDName(XYZ)
include => local
include => tollfree
But of course, this example won't work. The goal here is this: if a call
ends up being handled by the "local" or "tollfree" contexts, I want
those SetCID*** commands executed. Otherwise, I
2006 Oct 23
2
T.38 faxing with spandsp and Grandstream HT.486
Hello !
I 'm trying T.38 faxig with spandsp using rxfax/txfax as fax terminal.
As another endpoint I 'm using Grandstream HT 486 ATA and a fax machine.
Has anybody success with the HT486 as T.38 terminal ?
ATA as originator: I managed only onetimes a successfull T.38 fax
session. The other times the HT486 did not initiate a re-invite with
T.38 parameters. Or shall the Terminator
2005 May 28
1
Fax and SIP Device
A DID number was dedicated to receive fax, but i have the problem when
getting fax call,
which call will become a normal phone call and no fax was printed. When
fax is detected,
the fax extension is executed and dial the extension of the HT486 device
(firmware 1.0.5.22).
Somehow sending fax out working well. In the mailing lists, i notice
some are using HT286 and it work.
Could someone share
2005 Jun 24
4
Tellabs Echo Canceller
I am getting ready to experiment with the Tellabs 2752 echo canceller. I have a 255D shelf (and power supply), but am struggling a little on connecting the echo canceller to a PRI.
The shelf has 4 25-pair amphenol connectors. The two on the line side are marked "Receive In" and "Send Out". The 2 connectors on the drop side are marked "Send In" and "Receive
2004 Sep 16
2
No Caller Name sent from Asterisk over National or DMS100 PRI to a Norstar MICS?
I have a PRI link up and running between Asterisk and a Nortel Norstar MICS
v4.1 . I'm having a problem getting the textual Caller Name across the link
from Ast to Ns, however numeric Caller ID arrives and displays fine. From Ns
to Ast both elements come through fine. I'm forcing dummy values for testing
using:
exten => s,1,SetCIDName(Test)
exten => s,2,SetCallerID(1234561234)
2004 Aug 27
5
iaxtel and jitterbuffer
I am trying to work out IAX <--> IAX communications with my * box. I have a
registration with iaxtel and I thought I would start there for my learning.
I am able to call the number for Digium's support line (700-428-6000), but the
sound is horribly chopping. Some reading revealed the jitterbuffer settings,
so I enabled them in iax.conf. I have the following now:
; Inter-Asterisk
2005 Oct 04
3
Echo Canceling
I have been battling echo since we installed a new system at one of
our clients. I am using a single span digium card. I believe this is
the first time someone has setup a PRI in this area (its way out in
the middle of nowhere). We get slight echo on all calls, and when
calling some numbers (long distance calls but still in the local
area), we get very loud echo. The person calling out can hear
2004 Aug 19
1
Inband announcement of parking slot from app _parkandannounce?
Couldn't see the forrest for all the fascinating tree-like applications that
are out there:
For future reference, see:
http://www.voip-info.org/wiki-Asterisk+call+parking
:-)
-----Original Message-----
From: Kris Boutilier [mailto:Kris.Boutilier@scrd.bc.ca]
Sent: August 11, 2004 1:10 PM
To: asterisk-users@lists.digium.com
Subject: [Asterisk-Users] Inband announcement of parking slot from
2004 Dec 01
1
Hypothetical IAX2 situation
Two * servers: *a and *b.
Outside call comes in *b, and is automatically routed to *a. Someone on
a sip phone connected to *a then decides to transfer the call to someone
on a sip phone connected to *b. The transfer works.
At this point, is *a still in the converstation? Or is * smart enough
to see where the data stream is going/coming from?
Thanks for any help in advanced, and sorry if
2005 Jun 17
1
Dial timeout when server down
Hello,
When dialing somewhere and the other side is down, Asterisk waits until
dial timeout before sending "CHANUNAVAIL". I think that if after several
seconds there are not any reply (I mean at the IP level) we could
consider that the link is just down and handle the situation.
Is it possible to configure Asterisk to have this behaviour?
Many thanks.
Yves.
2005 Jun 24
1
Qualify Frequency
How frequent do the qualify packets go out?
I've got 5 phones at a remote location with ADSL and their qualify is
set to 5000.
I've noticed that they will go "UNREACHABLE" and then immediatly go
"REACHABLE" within a second or two.
We have this theory that the ADSL link (SBC) "caches" its route to our
network (where Asterisk is) and so we get bad ping