similar to: Noob help with IAX

Hi, I am fairly new at working with Asterisk. I am having a call quality issue that I really need to get ironed out before we go to rollout the system in a week. Any help would be greatly appreciated!!! Even if it is just pointing me in the right direction. My current setup: I have Asterisk Setup on a Dell Server. It has 2 T100P cards. One will be for out T1 PRI from the Phone Company (We

Hello guys. I am a fairly new user to Asterisk, and I'm just having a tough time. My goal is to set up a VOIP PBX. I have signed up with a BroadVoice number, and I have three systems with SIP phones. The PBX and the SIP phones are all behind a Cisco PIX running NAT. I am using Asterisk CVS version from yesterday. I also tried 1.0.3 with little luck. The SIP phones are two X-Lites on

Sorry if this comes in twice. Wasn't subscribed first time :-( Anyone help me here...... It worked once :-( I have a static IP address which is on my private network.. Phone is 192.192.192.220 and asterisk server is 192.192.192.22 I have the 7690 with a SIP iamge (Whatever latest is ) I have 3 lines setup with Free World Dial up and have the 4th setup to connect to my asterisk server.

Hello, I`m trying to make a call from the snom 100( SIP mode) but whatever number I dial I get a 404 error from Asterisk. Here are my configs and a dump from "sip debug" . But if I make a call from a Zap line (see extension 2382031), it rings the snom phone sip.conf: ------------------------------------------------------------------------------ ; ; SIP Configuration for Asterisk

I tried to update and build 1.4 (SVN-branch-1.4-r45775) tonight. I took the additional step of nuking my modules directory first... When I used the command asterisk -v to start asterisk, it seemed to go along and get to the point where asterisk is running(ie Asterisk Ready). At that point it was eating all available CPU. I went ahead and tried to register a softphone to it via IAX2, which

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi there, i have a working Microsoft ISA firewall with buildin H.323 Gatekeeper.... So Far, i got registerd the asterisk on the M$ Gatekeeper... here is the h.323 configuration: ; Open H.323 driver configuration ; [general] port = 1720 bindaddr = 0.0.0.0 allow=all ; turns on all installed codecs dtmfmode=rfc2833 gatekeeper =

All, I was a bit too focused on where I thought the problem was - turns out I wasn't crazy and the dialplan does work as expected. The problem was with dtmf detection - setting relaxdtmf=yes did the trick. Sorry for the premature post for help. Begin forwarded message: > From: Ben Witso <benw@bgwcomp.com> > Date: Mon Jun 21, 2004 7:28:42 PM US/Central > To: Asterisk-Users

Anyone help me here? I am a newbie so be gentle ;-)...... It worked once and then I played with the configs. I have a static IP address which is on my private network.. Phone is 192.192.192.220 and asterisk server is 192.192.192.22 I have the 7690 with a SIP iamge (Whatever latest is ) I have 3 lines setup with Free World Dial up and have the 4th setup to connect to my asterisk server. Here

Hello configuration as follows, dial-out works: capi.conf: [hfcpci] ;;PointToPoint (55512-0) isdnmode=MSN incomingmsn=* ;msn=61 controller=1 devices=2 context=incoming extensions.conf: [incoming] exten => _XX,1,Playback(demo-abouttotry) exten => _XX,n,Dial,SIP/xlite1 exten => _XX,n,HangUp When call is placed, the following debug info is shown, after the last line, it stalls until

My phone still says Not-Registered. I have a Polycom SoundPoint 600 SIP phone. Here is my sip.conf file: ; ; SIP Configuration ; [general] context=default ; Default context for incoming calls port=5060 ;added bindport=5060 ; UDP Port to bind to (SIP standard port is 5060) bindaddr=0.0.0.0 ; IP address to bind to (0.0.0.0 binds to all) srvlookup=yes ;

I am running asterisk 1.0.1 with OH323 compiled in. We have a 323 trunk to CallManager with a mgcp controlled pri router. When using sip phones (directly registered with asterisk) to call out the 323 trunnk to PSTN, calls timeout after 3 rings. If I answer b4 3 rings - no problem, otherwise I get "no one is available to answer at this time" on the consoel and it redirects to an

SIP SECURITY WARNING Version: v1-0 (cvs today) Problem: sip context in general section ignored - goes to default - allowing unauthorized sip devices to place calls in default context Fix [workaround]: Remove or rename "default" context in extensions.conf Notes: I am not sure what other asterisk functionality may be affected by this - review your other config

I have a problem that is probably so "doh" I will be embarrassed. However, I have spent all evening on this with no success: I have the following setup (asterisk cvshead as of today) 10 Channel EuroISDN<=>Asterisk<=>Meridian What I can do: Call from outside into the asterisk, dial an extension, and pass through to the meridian. WooHoo. What I can't do: Call from

hello, Im tryin to make Calls from MS Netmeeting(h323) to Xlite(SIP) it rings, but as soon as i answered it dissconnects!!!! This is what i get from the Asterisk console: -- Executing Dial("OH323/R27469", "SIP/xlite1|10") in new stack Aug 13 10:19:03 DEBUG[524304]: chan_sip.c:1265 create_addr: Setting NAT on RTP to 0 Aug 13 10:19:03 DEBUG[524304]: chan_sip.c:1500 sip_call:

strace on file access in asterisk shows that * is not even attempting to access the voice files. If I *manually* load app_playback.so, app_macro.so, and then pbx_config.so, I they will load and I get a dialplan. Ok, that's a problem -- autoconf is clearly not working, or there's some other related issue. So I try to use the demo and do "dial 500". This should connect and

Hello, These are error messages I get when I try to call a number over CAPI channel. -- Executing SetCallerID("SIP/xlite1-3b80", "0") in new stack -- Executing Dial("SIP/xlite1-3b80", "CAPI/hfcpci/b17") in new stack > data = hfcpci/b17 > capi request for interface 'hfcpci' == hfcpci: Call CAPI/hfcpci/b17-1 (pres=0x00,

Hello, I have the following setup: (*)<--->IP<--->Micronet 5012 H.323 box <---> POTS <---> PBX (Alcatel OmniPCX) Grand idea is to use the micronet's POTS interfaces to connect SIP phones to the PBX and to the PSTN. I think i even managed my way in the arcane and cryptic management interface of that appliance, but I am stuck against theese messages: -- Executing

Hi list, i've problems with my * server and the 4 phones which are linked to it. i've 2 grandstream bt100 with the firmware upgraded to 101, a wi-fi phone (i don't know its brand) and another ip phone i don't know its brand. with this sip.conf : [general] port = 5060 bindaddr = 192.168.100.229 context = default ;x changed from default to sip localnet = 192.168.100.0/24

Does anyone kmow what these errors mean or how they can be fixed. I'm using asterisk on a Fedora Core 2 box with a TDM400P with 2 fxo and 2 fxs ports. Dec 29 17:17:52 WARNING[6019]: chan_zap.c:5469 ss_thread: Channel Zap/4-1 in prering state, but I have nothing to do. Terminating simple switch, should be restarted by the actual ring. -- Hungup 'Zap/4-1' == Starting post

I am using version: CVS-v1-0-12/13/04-18:46:23 with a TDM400p (2 fxo, 2 fxs ports) and I keep getting errors along with phantom calls: Dec 21 16:02:07 NOTICE[5872]: chan_zap.c:5363 ss_thread: Got event 17 (Polarity Reversal)... Dec 21 16:02:14 WARNING[5872]: chan_zap.c:5434 ss_thread: CallerID returned with error on channel 'Zap/4-1' my analog phone reads caller ID info fine when