similar to: TDM400 not working

Of course I am not a kernel expert, so .. please be patient. I am investigating on my zaptel/zapata problem. As the main error message asterisk quits on mentions <'/dev/zap/channel': No such file or directory> I went peeking over there. [Asterisk Verbose Error Mar 13 20:43:35 WARNING[5779]: chan_zap.c:763 zt_open: Unable to open '/ dev/zap/channel': No such file or

I installed TDM400P and X100P pci cards in a system running mandrake 10.1 official, kernel 2.6.8.1-12mdksmp. I can compile zaptel, libpri, asterisk and modprobe (zaptel, wcfxs, wcfxo) without errors. Except that running ztcfg and asterisk fails. [root@asterisk asterisk]# ztcfg Notice: Configuration file is /etc/zaptel.conf line 3: Unable to open master device '/dev/zap/ctl'

Hi, all I have installed TDM400 with 1 FXS and 1 FXP ports. Now I am goig through documentation on how to configure it. It mentions 3 protocols: Loopstart, Groundstart and Koolstart. Which one do I use? Can someone send me sample zaptel.conf file for Australia? This will save me some time and will be used as a working example. Thanks, Rudolf

Hi, all I am building a new server. Have installed FC 6 and put in TDM400 card. Checked out latest asteriusk code, run make install in zaptel directory. So far all is fine. Now I am trying to install the drivers. # modprobe zaptel FATAL: Module zaptel not found. Fair enough, no zaptel driver is found on the system. Is there are any known problems with FC6? I did not have much trouble running

Hi, all I am doing "prrof of concept" system. I will have two IP phones connected to Asterisk box. Box itself will have 1 PSTN conenction and one analog phone conenction. A basic minimal configuration. At the moment I am planning to use an old PII-350 with 128M of RAM I have lying around. I can not test anything yet, as I am waiting for phones to arrive, so question is will that be

I excitedly installed my TDM dev kit earlier this weekend, installing asterisk and all the kernel drivers to make it work. And it did, it was fantastic. I then reboot the machine, and even after doing a modprobe wctdm, I get the following: == Parsing '/etc/asterisk/zapata.conf': Found Jan 31 13:34:27 WARNING[342]: chan_zap.c:793 zt_open: Unable to specify channel 1: No such device or

Hi, all Stupid question, but how do you exit asterisk console without stopping the asterisk? Tried quit and exit: *CLI> exit No such command 'exit' (type 'help' for help) *CLI> quit No such command 'quit' (type 'help' for help) *CLI> Any other ideas? I started asterisk with -cvvvvg option. Same problem if use asterisk -r to connect. Can not exit. Any

Hi, all I am in Australia and I have to setup Asterisk in few offices. There will be IP phones in each office and I must be able to call between offices. I need actual handsets. I need "standard" handsets to be used by people. Those must support features like CID, call forward, etc. --- your normal office feature set. Also I need some sort of more complex handset to be used by

Hi, all I want voicemails to be delivered to recepients by e-mail. I have set up voicenail, and I can see asterisk is using sendmail to send messages out. Using Ethereal, I can see that messages are leaving my network, but receipeint mail server never replies back. As a result, mail delivery is timed out. I got a book on sendmail and it looks quite complex. It will take quite a bit of time

Hi, all I am still battling to connect * and voipbuster. What protocol does it use? Ethereal capture shows UDP traffic, but no SIP or IAX traffic when using their client. VoipBuster client connects to connectionserver.voipbuster.com on port 11112 for authentication. Call itself is placed on different server. I have tried to connect using SIP and IAX and it seems that no authentication is

Hi all, this time with the complete configuration files... We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap

Hi all, We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap modprobe wcfsx then the ztcfg output this: Zaptel

hello i am using asterisk-1.0.9. i have a NAT problem. without NAT registration is ok. and if user is bhind NAT it is registring on asterisk. but SJPhone is showing "not registered". i think asterisk is properly sending request to UA. any comments............this sip.conf setting was working previously -- Registered SIP '5000' at 0.0.0.0 port 5060 expires 120 -- Saved

Hi, I'm using zaptel-1.2.22.1 with asterisk-1.2.10 and following steps to make zaptel working... OS is gentoo linux 2006.1 Hardware: --------- 0000:05:01.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device 8085:0003 Flags: bus master, medium devsel, latency 32, IRQ 22 I/O ports at b400 Memory at ff900000

Hi, all I am trying to figure out how to forward incoming PSTN call on SPA3000 to VoIP extension(s). Basically, I have converted my home to VoIP. I have normal phone (connected to SPA3000) and couple of IP phones. All call coming from VoIP DID do ring all phones (analogue via SPA3000 and IP ones). Now I need to do same thing for incoming PSTN calls. I have enabled gateway function in SPA3000 and

Hi, all I have couple of SIP phones and they are in [from-sip] context. I also have an IAX2 phone. I have put this one in [iax-user] context. I want to make calls between SIP and IAX2 phones. If I put them all in same context all is fine, however when they are in different contexts they will not call each other and I will get message (in * CLI) that particular extension does not exist in a

I have a number of Polycom phones to setup with my * server. For my initial few phones I hand wrote configs. Does anyone here who uses Polycom phones have some form of management utility for automating their setup? Michael -- Michael Graves mgraves@pixelpower.com Sr. Product Specialist www.pixelpower.com Pixel Power Inc.

Hi, all Did anyone tried TDM400 card on old main board (Intel 440LX chipset -- PII)? The reason I am asking is because TDM400 needs PCI2.2 and main board is PCI2.1 I do not want to upgrade yet. Thanks, Rudolf

G'Day All, Can anyone give me some direction in setting up the TFTP server on my RadHat ES3 box? I did quite a bit of reading, but I think I am more unsure now than before. I found the information nebulous. TFTP is already installed. I am trying to determine where the root directory for the tftp services is located so I can copy the CISCO 7960 firmware files onto it. Thanks.... Ferg

Hi All, I cannot get my TDM to work correctly. In my /etc/zaptel.conf file I have loadzone = us defaultzone=us fxoks=1 In my /etc/asterisk/zapata.conf file I have [trunkgroups] [channels] context=from-pstn usecallerid=yes hidecallerid=no callwaiting=yes usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes canpark=yes cancallforward=yes