similar to: Results of an incorrect crossover pinout??

We have integrated an Asterisk (TE110P) and a Mitel SX200. We usually get over 500 frame errors and over a 500 slip errors per hour. When the errors reach 1000 per hour the Mitel will take it's T1 card offline. At that point no calls can be routed from the Asterisk server to the Mitel and the TE110P reports a Yellow alarm. What can be causing all these Frame and Slip errors? We have been

Hello all. I just received a TE110P and am trying to hook it to my Mitel 200SX has anyone successfully done this? My configuration is as follows. Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card. All I get is a blinking yellow on my TE110P card and an alarm on my Mitel. T1 card. Any advice would be great. Zaptel.conf span=1,0,1,d4,ami e&m=1-23 dchan=24

I have a small government department that wants me to implement a Asterisk installation, however, they connect to the Government PBX, a Mitel SX200, and want to keep the ability to do that. I know there is no chance to connect the digital extension lines, but would it be possible to have the pbx admins send analogue extensions over and have those lines interface through an FXO interface? Or

How would you categorize a Yellow Alarm sensed by the Asterisk side in a Legacy PBX integration? We have a Mitel SX200 connected to an Asterisk(1.2.4) with a TE110P. Twice today (first time in over a month) we received a Yellow Alarm on the TE110P. I have been able to clear it easily by restarting zaptel. Thanks in advance! -------------- next part -------------- An HTML attachment was

The "telco guys" probably did something non-industry standard and reversed send and receive in the jack that they plugged the CAT5 into. Sure it works, sure it is easier, sure it is not the correct way of doing things. Thanks, Steve ________________________________ From: asterisk-users-bounces@lists.digium.com on behalf of Lacy Moore - Aspendora Sent: Sat 4/22/2006 2:55 PM To: Paul

We are trying to debug a connection between Asterisk and a legacy PBX (Mitel SX200). We turned on the Zaptel debugging and we get the following message quite frequently: Oct 12 07:14:09 localhost kernel: T1: Lost our place, resyncing ( 28 ) Oct 12 07:14:09 localhost last message repeated 3 times -- Oct 12 07:14:11 localhost kernel: T1: Lost our place, resyncing ( 28 ) Oct 12 07:14:11 localhost

Hi, Digium's E400P has RJ45 conector and my E1 link has BNC concetor. Could someone tell me the cable pinouts to make this conection? thanks Eduardo

I have used cross-connect wire from the spool to make T1 crossover cables with RJ45 ends. All that matters is that pin one goes to four and two goes to five on both ends. ________________________________ From: asterisk-users-bounces@lists.digium.com on behalf of Andrew Sent: Sat 4/22/2006 2:51 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: Pinouts for T1/E1

I tend to use the soft sell. Looks like I Just self-promoted :-) -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of John Novack Sent: Saturday, April 22, 2006 12:05 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: Pinouts for T1/E1 crossover cable WAS "RE: [Asterisk-Users]

> -----Original Message----- > From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users- > bounces@lists.digium.com] On Behalf Of Kevin P. Fleming > Sent: Monday, April 24, 2006 12:14 PM > To: Asterisk Users Mailing List - Non-Commercial Discussion > Subject: Re: Pinouts for T1/E1 crossover cable WAS "RE: [Asterisk-Users] > whatcable to connect a legacy PBX to

I for one think it is a great idea to buy a book with hard earned money and wait a few days to a week just to get an answer to a question that is freely available on the internet immediately. Hard pressed to think of anything in the "book" that is not on with wiki with more up to date and useful information. -----Original Message----- From: Alexander Lopez

At Sangoma we do quite a lot of back-to back T1 and E1 connections. T1 is not a very fussy connection, as the baud rate is only about 750 kbps. In our experience, for error free communications you can use the following rules of thumb: Up to 50 ft: Flat patch cable Up to 500 ft: Ordinary twisted telephone cable Cat 5 may be overkill unless you are going hundreds of feet. David Yat Sin

Dear, I have two Asterisk PBXs with an E1 interface/RJ-45 port in both boxes. I need to connect both PBXs with E1/R2 and UTP cable. What are the requirements to deploy the UTP cable ??? Straight-through or crossover ??? What are the pinouts in both peers ??? Thanks a lot, Alejandro

Hello all, I have obtained a Compaq T700 H UPS sans-cable. My research indicates it would've come with a HP #201092-001 cable, and from previous posts on this list, it speaks upscode2, possibly being a rebadged Eaton unit. Any suggestions for cable pinouts I can try? Regards, Mathew McBride

Just cross pairs 1-2 and 4-5 1 <--> 4 2 <--> 5 Never done an E1, but I think it's the same for a T1 4 wire cable. Tim Thompson Commercial Sales Engineer http://www.amatechtel.com (806) 722-2227 -----Original Message----- From: bam [mailto:bam@cqm.co.uk] Sent: Monday, December 29, 2003 9:12 AM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] E100P pinouts

Eric "ManxPower" Wieling wrote: >> >>> span=1,1,0,d4,ami >>> e&m=1-24 >>> > > Looks like you have told Asterisk to get it's timing from the Mitel. > I'll bet the Mitel is trying to get it's timing from Asterisk. > > Try span=1,0,0,d4,ami and run ztcfg -vvv > I just set this back. It was originally set to your

Does anyone have any experience getting a Mitel SX-200 EL/ML PBX system to work with *? I'm not getting inbound or outbound calls to work. (Inbound caller gets line busy tone.) SETTINGS FROM MITEL: I built a Crossover cable and connected it like this: PSTN--T1--ASTRISK--T1--OLD MITEL -Crossover Cable Pin-out: 1 - 4 2 - 5

Hi, I have a Cisco 7960G phone for which I know the pinout of the headset socket. I have a couple of standard telephone headsets which I do not know the pinout of. I'd like to connect the two. If I have the pinout of a normal/standard headset I can rewire the ones I have to match the cisco. Thanks Mike

Hi Asterisk Community, I have a development with a TDM11B in it. I am trying to connect this to a exchange line as well as a UK telephone and are looking for some pinout information for the FXS port. Is it the centre 2 pins that at the tip and ring. I have been digging around the Digium site but cannot seem to pick up this info. Any help appreciated. Thanks -- Gary

I am trying to test the T1 card in our legacy PBX but the connector to the card is a 15 pin serial cable. I would like to make it myself so I can try this test today. Does anyone have a pinout for it? I just made a T1 RJ-45 loop back to test my TE110P and it tested out fine. I'm trying to resolve some timing issues and a tech from Digium is going to ssh in and walk around my asterisk server