Displaying 20 results from an estimated 5000 matches similar to: "chan_capi-cm, Euro ISDN bus: 2 extensions on same BRI port not working"
2006 Feb 23
1
chan_capi-cm 0.6.4 random outgoing MSN problem
I've having a big problem after having upgraded to 1.2.4 and
chan_capi-cm 0.6.4
When making outgoing calls I don't seem to have any control over the CLI
that is presented to the called party -- it can be any one of the MSNs
allocated to the line, allocated on what seems to be a random basis.
This is on a BT Business Highway line (which is essentially an ISDN2e
line with two built-in
2003 Nov 19
1
fritz pci / chan_capi / australia setup
Hi * Fans,
I have some fritz cards now, followed instructions from stuart hirsts email of Jun 28:
->
Thanks for your info but I think I have it working at last. Below are
the steps I took which might help others.
1) Download the PCI AVM drivers from ftp://ftp.avm.de/cardware
2) Download the Chan_capi from http://www.junghanns.net/asterisk/
3) tar -xvzf fcpci-suse8.0-03.09.10.tar.gz which
2006 Jun 29
4
Very bad quality with AVM Fritz!card PCI and chan_capi
Hi everyone,
I have Asterisk SVN-trunk-r7498 running for a few months and I'm quite
happy with it. However, I am experiencing a quality issue with my AVM
Fritz!card PCI which is used with chan_capi. When somebody calls me on
this line he hears a lot of noise and I hear "scratches" and "plops". It
is very annoying. Below is is my /etc/asterisk/capi.conf
I've tried to
2004 Dec 02
2
more than 3 msns with chan_capi
I have 10 msns on my isdn bri incoming (AVM Fritz, chan_capi 3.5)
When i set in capi.conf
[interfaces]
msn=1,2,3,4,5,6,7,8,9,10
incomingmsn=*
controller=1
softdtmf=1
accountcode=
context=tcom-in
echocancel=yes
devices=2
Only msn 1,2,3 are working.
What can i do?
Thanks
Jens
2006 Jan 26
3
Chan_capi on builds 7955>8320 strangeness
Hello All,
I am having an odd problem with Armin's chan-capi_cm on builds higher
than 7955.
It would seem that this happens on anything higher than 7955.
What is happening is the isdn is ringing, then asterisk does a goto-if
and just hangs.
Asterisk itself is ok, but the isdn then rings out or busys out on the
other side.
Outgoing works fine, this only seems to effect incoming.
I
2006 Mar 15
1
AVM C2 chan_capi-cm-0.6.3 Error on Dial
I'm getting a strange error on one of the two controllers on an AVM C2
card under chan_capi-cm-0.6.3.
I have two ISDN controllers defined, both in the same group, both
connections are UK ISDN2e Point to Point:
On the third outbound call (both of the first two calls are handled by
the second controller "ISDN2",) I get this error :
chan_capi.c conf_error 0x2001 PLCI=0x301
2006 Jun 04
5
chan_capi-cm-0.6 and incoming calls problem
I have a problem receving calls via the ISDN line, using the followin
components
Asterisk 1.0.9 with asterisk@home
chan_capi-cm-0.6
AVM Fritz card
datalink protocol = point to multimode
I can make calls out with no problems so the issue is only incoming calls.
When I make the call from an external line to the ISDN line connected to
asterisk, I get a busy signal after about 5 seconds. I have
2004 Jun 07
6
chan_capi and DDI (Anlagenanschluss)
Hi all !
We have 3 NTBAs which are all going to our existing PBX. Our areacode is
06003 and our DDI enabled number 9141.
I want to exchange that PBX with Asterisk, but still struggle to get it
working.
My CAPI.CONF is currently like this:
[general]
nationalprefix=0
internationalprefix=00
rxgain=0.800000
txgain=0.800000
[interfaces]
context=in-capi
msn=60039141
incomingmsn=*
controller=1
2004 Feb 17
5
chan_capi problem
Hi to all
I've mada up my mind and i tried to change from i4l to chan_capi, following some councelling from the gurus.
I compiled it up, and when i try to load it in modules.conf, i get that wonderful message and Asterisk does not start:
[chan_capi.so]Feb 17 09:21:40 WARNING[16384]: loader.c:239 ast_load_resource: /usr/lib/asterisk/modules/chan_capi.so: undefined symbol: ast_get_group
Feb
2005 Jul 22
1
Chan_capi MSN problem
All,
before I start, I have read the readme and realise the dial syntax has
changed since 3.5.....(and I really wish it hadn't).... anyway can
somone please help me round a config issue?
Previously I had a capi.caonf as follows. This config allowed me to have
multiple MSN's on the same ISDN/Fritz! card under seperate contexts.
2006 Jan 16
1
chan_capi-cm and DID
Hi all,
i have asterisk 1.0.9 with an Eicon Diva 4bri and
chan_capi-cm-0.6. I have 2 NTBAs (one with did and one
without).
When using the one without did, i am able to place
outgoing and incoming calls. When i use the NTBAs with
did i have a layer 2 error.
Anyone an idea?
-- Executing Dial("SIP/2004-9634",
"CAPI/g1/43XXXXXX") in new stack
> data = g1/43XXXXXX
2004 May 12
1
Multiple ISDN controllers & Capi
Hi,
how can I set up multiple ISDN controllers with chan_capi, so
that every controller has its own configuration (MSNs to
listen etc...) ?
I know I can configure "controllers=1,2" in chan_capi's capi.conf
but then the controllers have the identical configuration
and context within asterisk.
My setup: I have 2 BRI-controllers (in one AVM C2).
1. BRI: point-to-point, Number:
2004 Jul 17
3
chan_capi: sending incoming calls to different contexts
Hello,
I am using chan_capi and would like * to behave differently depending
on the MSN the caller dials.
Is there a way to route incoming ISDN calls to different contexts based on
the MSN dailled?
I have tried something like
msn=1234
incomingmsn=1234
context=msn1
msn=4567
incomingmsn=4567
context=msn2
in capi.conf but with no results.
Thanks for any hints.
-Walter
--
Walter Doerr
2005 Sep 29
4
chan_cap-cm-0.6 deflect support
Hi,
I've recently reinstalled a Diva in my asterisk server (alongside a
QuadBRI :-) to test the nice features Armin has been adding in
chan_capi.
The capi.conf format has changed, so my question is how do I define a
deflect= statement for different incoming MSN's?
I've tried to define a section for each (group of) MSN with a different
"deflect". Is that correct?
[DIVA1]
2005 Aug 27
1
Asterisk ISDN: Problem Setting CallerID as DID Extension Numbers.
Hello Group,
Current Setup:
- Eicon Quad BRI ISDN Card.
- 4 ISDN BRI (Telco: Telstra) Onramp2 services.
- Mode: Point2Point.
- 100 Indial Number ranges. Full National Number (9 digit format): BAAAAAAXX
where: B (Area code): 2/3/7/8
A (Normal Numbers)
X (99 Indial extensions)
eg: BAAAAAA00
BAAAAAA20 etc
Requirement:
- To be able send Indial numbers as Caller ID when dialing out.
Configration:
2004 Apr 08
2
Réf. : Re: Fritz ISDN PCI v2 and CAPI
I tried that but it still doesn't work... I think I don't have the correct
approach. Have I to install any ISDN drivers (=modules ?) BEFORE dealing
with CAPI ?
If yes, why shouldn't I use the hisax drivers (which are kernel ones)
instead of fcpci drivers (which doesn't seems to work, by the way...)
And finally, how is it possible to link the two modules together?
As you can see,
2006 May 16
1
chan_capi-cm and type of number problem (ToN)
Hi!
I have problems with the ToN configurations in chan_capi-cm. I
understand how incoming calls are rewritten using national and
international prefix. But for outgoing calls - what is the ToN?
Further, is there any debug info of the Ton? "capi debug" and the
divactrl dchannel both show the CLI and CDLI, but do not show the ToN.
How can I set the ToN? I suspect chan_capi to use the
2007 Mar 22
1
Problem in using Two BRi Cards in Asterisk
Hi,
I have done my best and tired of searching the net about the problem. If anybody could help
would be a great favour.
Description of Problem
------------------------
I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim
is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture
manual. After installation dmesg
2004 Dec 13
3
Busy message on ISDN cards?
Hi all,
I'm new to asterisk and not too knowledgeable on ISDN, so please be gentle :)
I have a dual-channel Eicon Diehl Diva card in a Debian Woody box with
kernel 2.4.27, connecting to a Telstra (Australia) Onramp Home Highway
ISDN line. I'm pretty certain the card and line both work since
they've been used in this machine for PPP before this (but with an
older kernel with DoV
2006 Feb 11
4
Problem with Wait() and chan_capi-cm?
Hi!
I am playing around with Asterisk and have a problem :-)
(Asterisk-version: 1.2.4, chan_capi-cm-version: 0.6.4)
I have a sip-phone at my desk and an ISDN-phone (independent of the
Asterisk-server) in my living room, when I'm not at my desk, the
sip-phone is switched off. I would like to be able to accept calls at
both phones (when available) and have Voicemail kick in if I don't