similar to: Submitting ISDN-MSN from a SIP-Phone

Hello, I am using a system with an AVM ISDN PCI card (fcpci) and asterisk with chan_capi-cm-0.6. The hardware is connected to a Siemens Hipath 3550 PBX. As a BRI connection has 2 channels and allows 2 simultaneous calls, numbers/MSNs 6391 and 6392 were for provisioned for each channel. The system is working (partly, read on), the trick is the correct cable wiring and setup the PBX's port

Hi, how can I set up multiple ISDN controllers with chan_capi, so that every controller has its own configuration (MSNs to listen etc...) ? I know I can configure "controllers=1,2" in chan_capi's capi.conf but then the controllers have the identical configuration and context within asterisk. My setup: I have 2 BRI-controllers (in one AVM C2). 1. BRI: point-to-point, Number:

Has anyone a working /etc/asterisk/capi.conf example for Germany or Switzerland using the AVM C4 - ISDN Card. I try to connect asterisk to 3 wires BRI-ISDN (Swisscom). I appreciate your help and it would save me a lot of time, figuring it out by myself. regards, Claudio

Hi, I was trolling through the archive to see if it was possible for asterisk to ignore certain MSNs. I have a AVM Fritz/BRI with two MSNs: 7770001 and 7770002. I would like asterisk (with chan_capi) to ignore 7770001 such that a regular phone on the bus will ring; calls for 7770002 should be picked up by asterisk. I configured msn=7770002 incomingmsn=* within capi.conf and figured this would

Hello Group, Current Setup: - Eicon Quad BRI ISDN Card. - 4 ISDN BRI (Telco: Telstra) Onramp2 services. - Mode: Point2Point. - 100 Indial Number ranges. Full National Number (9 digit format): BAAAAAAXX where: B (Area code): 2/3/7/8 A (Normal Numbers) X (99 Indial extensions) eg: BAAAAAA00 BAAAAAA20 etc Requirement: - To be able send Indial numbers as Caller ID when dialing out. Configration:

Hello everyone, I have Asterisk SVN-trunk-r7498 installed on a server (celeron 2.4 Ghz, 256MB) with a TDM40b a TDM04b and an avm fritz!card pci. I experience a problem with voicemail: my messages are good unless the incoming call comes from isdn, which means via the avm fritz!card. In this case (and in this case only) the message is disjointed and I can hear at most 1 second out of a 1 minute

I have 10 msns on my isdn bri incoming (AVM Fritz, chan_capi 3.5) When i set in capi.conf [interfaces] msn=1,2,3,4,5,6,7,8,9,10 incomingmsn=* controller=1 softdtmf=1 accountcode= context=tcom-in echocancel=yes devices=2 Only msn 1,2,3 are working. What can i do? Thanks Jens

Hi, I am using Asterisk on a DSS1 ISDN-BRI with ISDN4Linux (and a Fritz Card PnP). The ISDN-BRI is in PTP-Mode (Point to Point "german: Anlagenanschluss") which is enabled within I4L with "hisaxctrl fcpcipnp0 7 1". Everything works fine except that I can not see the called number/MSN of incoming calls within Asterisk and because of this I can not route incoming calls

Hi everyone, I have Asterisk SVN-trunk-r7498 running for a few months and I'm quite happy with it. However, I am experiencing a quality issue with my AVM Fritz!card PCI which is used with chan_capi. When somebody calls me on this line he hears a lot of noise and I hear "scratches" and "plops". It is very annoying. Below is is my /etc/asterisk/capi.conf I've tried to

Hi! I'm goining to connect an AVM C4 to 4 BRI-lines in PTP-Mode, all BRI-lines will have the same number (1234-XX for example). I don't know if this is possible and I can't test it, because I don't have these lines yet. Is anybody out there, running such a configuration? I'm looking for some example configs. Especially I want to know how it is possible, to let asterisk

I am going to try and use a passive AVM fritz BRI card for my * setup.. Here is the thing.. I need to order my BRI from BT.. The service that looks to be the one to use is what they call ISDN 2e becasue this has the option to setup hunt groups across multiple ISDN2e lines so I could add another line later to get 4 channels.. According to the BT website in order to use the hunt grouping across

I have a problem receving calls via the ISDN line, using the followin components Asterisk 1.0.9 with asterisk@home chan_capi-cm-0.6 AVM Fritz card datalink protocol = point to multimode I can make calls out with no problems so the issue is only incoming calls. When I make the call from an external line to the ISDN line connected to asterisk, I get a busy signal after about 5 seconds. I have

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

Hello everyone, I'm using very simple setup to make and receive external ISDN calls through a softphone (x-lite version 3.0 - Win32) via an asterisk box. Hardware setup: - Dialogic Diva BRI (lspci yields: Network controller: Eicon Technology Corporation DIVA Server BRI-2M/-2F (rev 01)) - ISDN BRI line Software setup: - Redhat 9 - asterisk-1.4.16.2 - chan_capi-1.0.2 Asterisk configuration

Having ISDN FXOs and a bunch of ISDN DECT base stations, I went looking for a CAPI compatible active BRI adapter capable of NT mode. I have found that the 'Eicon Diva Server 4BRI' fulfills theses requirements. However, at EUR 1387 for four BRI interfaces, it does not come cheap. Are there other users of similar hardware that can point me to alternatives ?

Hi, Anybody have lots of experience with PCI ISDN cards and Asterisk? I'm thinking of getting a BRI in my house to deliver more advanced signaling to my PBX (yes, I'm a geek :-)) but I've never played with isdn4linux. Is there any particular BRI card that works better with Asterisk than any other? Also, can the BRI interface cards participate in conference, etc., since they

I want to test asterisk with its DID functions on a smaller scale without the expense of a PRI. I am in the US, and want the most reliable/stable, and feature rich solution that I can have. What ISDN card would be reccommended? My clec switch operator says he can/will send DID info to my BRI's if I wish. Can Asterisk, or one of its addons support this? What BRI solution would be

O.K. thanks a lot, Felix and Peer Oliver. But somehow asterisk keeps telling me while startup: [chan_capi.so] => (Common ISDN API for Asterisk) Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr1 Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr2 Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr3 Jan 24 14:30:47

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi there, i'm in debian sid 3.1 with kernel 2.6.7, * last cvs & chan_capi 0.3.4b; nt1+ with 2 bri in ptmp (http://www.voip-info.org/tiki-index.php?page=DDI) i tried to install avm c4 following step by step http://www.voip-info.org/tiki-index.php?page=Asterisk%20How%20to%20connect%20with%20CAPI step 1. i compiled capi 2.0 support in kernel

Hi All, We've got msidn configured: Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060) iend(0x8fd5060) and running on Asterisk 1.4.21.2: pbx*CLI> misdn show stacks BEGIN STACK_LIST: * Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0