similar to: Red or Yellow alarm monitoring

We are running Asterisk version 1.4.23-1, libpri-1.4.9 and zaptel-1.4.12.1 and two Digium TE220Ps. Debugs are set to 10. We have a T1 PRI connected to the telco. Over the last 4-5 days, we have getting Yellow/Red alarms coming from the T1 PRI. The other two ports in use are connected to internal test switches (Avaya Legend/Avaya Definity), and are not showing any errors.

Folks, I really hope you can help me here - I'm beginning to tear my hair out! About 10 days ago my company moved to a new office. As a result of this, we've plugged our PBX box, which has happily been running for the last three years, into our new E1 line. Since then, I've been seeing intermittent yellow alarms. Obviously, since this was working fine in the old office, the thing to

i get this message with a red signal on TE110P card: ***************** TE110P: span configured for... Calling startuo (flug is 4099) wcte1xxp: Setting yellow alarm ***************** what does mean ? thank you :)

About every hour I see the yellow alarms on all or a number of channels of my PRI which is connected to the dutch telephony network, Asterisk keeps on working fine.... Here's an example where channel 1-24 went into alarm: WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event): Detected alarm on channel 1: Yellow Alarm WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event):

Hi, Ok, I put the new TE410 into our system last night - This is the second TE410P card. There is also TDM400P in Slot 5 with IRQ 9 which is shared with aic7xxx (SCSI) According to "cat /proc/interrupts", the new card is in the second slot using IRQ 11 (the first card is in slot 1 on IRQ 10 - but always has been). With only the original card install, there has been no issues with

How would you categorize a Yellow Alarm sensed by the Asterisk side in a Legacy PBX integration? We have a Mitel SX200 connected to an Asterisk(1.2.4) with a TE110P. Twice today (first time in over a month) we received a Yellow Alarm on the TE110P. I have been able to clear it easily by restarting zaptel. Thanks in advance! -------------- next part -------------- An HTML attachment was

Hello Approximately every 15 minutes I'm getting the following error (on all channels): [Apr 7 01:34:27] WARNING[6530]: chan_zap.c:6628 handle_init_event: Detected alarm on channel 31: Yellow Alarm [Apr 7 01:34:27] WARNING[6529]: chan_zap.c:2388 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! [Apr 7 01:34:27] == Primary D-Channel on span 1 up

Dear list I am facing strange issue. i have 16 PRI setup. out of 16 there are 2 cables which are giving me yellow alarm in if they are in card number 1 and works fine if i put in card2 what could be the error is it card faulty?? -- Akib Sayyed Matrix-Shell akibsayyed at gmail.com akibsayyed at matrixshell.com Mob:- +91-966-514-2243 -------------- next part -------------- An HTML attachment

Guys.. I just saw this for the first time... I did some google and wiki without any luck.. what does a red or yellow alarm mean in zaptel? Feb 23 02:54:16 WARNING[16890]: chan_zap.c:5865 handle_init_event: Detected alarm on channel 2: Red Alarm Feb 23 02:54:24 NOTICE[16890]: chan_zap.c:5860 handle_init_event: Alarm cleared on channel 2 This just happened by itself..

Folks, I installed a te110p to connect to an E-1. Ensured the jumper is on for E-1, installed the card, and got the following from the phone company: hdb3 encoding (verbally confirmed ccs) euroisdn switchtype pri signalling So I set up zaptel.conf: span=1,1,0,ccs,hdb3 bchan=1-15 unused=17-31 dchan=16 loadzone=us defaultzone=us Card tries to come up but goes into RED alarm. Occasionally cycles

Hi, I have 2 servers: one is running 2 B410P cards with 8 euroisdn lines (mISDN) connected on it, everything runs fine. I prepare a new server - HP 360 G8- with 2 HA8 cards each of them 1 module of 4 lines. Already had with this machine an RMA on both cards as they was faulty and crashed the server. What happends is that when I connect cables on the HA8 modules (those cables are unpluged

SYNOPSIS Erratic red alarm T1 PRI on asterisk, but zttool running concurrently during alarm shows no errors, irq misses, or alarms, on any span. Using asterisk and quad Digium T405P, configured as follows: Span 1 connects to ISDN PRI (fractional 8 B channels, D channel 24). Span 2 connects to T1 Mux and analog stations. Span 3 connects to ISDN PRI Nortel BCM hybrid key system digital trunk.

Hi all, any body can tell me why i am receiving this message in my sever ? I have running * with 10 Digital Lines, but i am receiving a lot of times this message . Is a software issue or is a hardware issue ? Regards. Mar 27 12:58:24 WARNING[2586]: chan_unicall.c:2672 handle_uc_event: Unicall/5 event Alarm Mar 27 12:58:24 WARNING[2586]: chan_unicall.c:3091 handle_uc_event: Unicall/5 Alarm masks

Calling out on PSTN over a TDM400P seems to generate a Red Alarm - whatever that is. I have another extension on the PSTN, and I can dial out over that. zttool shows no alarms. asterisk*CLI> zap show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO Wildcard TDM400P REV I Board 1 OK 0 0 0 CAS Unk YEL 0 db

Hello, I am missing any description of zaptel/DAHDI alarms. The TE200 series user manual contains only a description of LEDs states. These alarms states are visible in zttool/dahditool or in astersick CLI (zap show status) and I wonder what is the real meaning of these alarms for E1 channel. Possible alarm states (based on zaptel.h 1.2): 1. No alarms 2. Recovering from alarm 3. In loopback

Humm, if I put a filter in this lines, maybe back? 2016-01-05 12:36 GMT-02:00, Ryan, Travis <RyanT at oscarwinski.com>: > >> -----Original Message----- >> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- >> bounces at lists.digium.com] On Behalf Of Vitor Mazuco >> Sent: Tuesday, January 05, 2016 9:21 AM >> To: Asterisk Users Mailing

Alarms Span RED wildcard X101P Board1 OK wcusb/0 0 ive got my asterisk server up and running and working correctly, the first time after a reinstall and reboot everything was fine - i had both alarms OK and i could get the USB extension ringing when i ran the house number from my mobile. as soon as i tried again i got a red alarm on the wildcard board. now im using the sample

I am currently helping a friend build an Asterisk PBX that spans several cities using anything from T1s to DSL connections to link remote SIP phones, IAX gateways, etc. to a central Asterisk PBX server that serves up voicemail, features, etc. The biggest problem that I have had with this system appears to be the leading problem that my day job company finds with their VOIP deployments: Most

I found one of UPS has a ups.alarm : Battery charger fail! Internal UPS fault! Is there a way to monitor for this kind of failure? In upsmon I did not find and event type for alarms like this... Thanks Adam Pribyl

On Mon, 17 Jun 2019, Adam Pribyl wrote: > I found one of UPS has a > ups.alarm : Battery charger fail! Internal UPS fault! > Is there a way to monitor for this kind of failure? In upsmon I did not find > and event type for alarms like this... See github issue "upsmon: add ALARM support #415" https://github.com/networkupstools/nut/issues/415 dated 4th April 2017.