similar to: i4l ring indication problem, again...

Hi all, I have an EICON DIVA PCI 2.02 with I4L. I'm unable to call some numbers, in general numbers with automatic responders that do not rings. It's seems asterisk does not understand that the other party has answered, so after a timeout it reports 'busy', but in real the other end has answered. Any other call to a "normal" number works fine. Did somebody experience

Sorry for a slightly off-topic question, but I'm getting desperate. I tried to use asterisk to talk w/ ISDN line and tracked the problem to i4l. I have a Diva PCI 2.02 (S/T) card and am running RH8 w/ 2.4.20 kernel (first version that supports the 2.02 w/ hisax driver). The switch is a 5ESS running NI-1 protocol. The card sync's up and reports other traffic on the line, but fails to

I have * with i4l installed and working - on a dumb eicon card. It seems in order to get DTMF out of the BRI (for business banking - etc) - I should change from i4l drivers to capi drivers. wiki help seems to be for the Fritz card only...??? I have ticked the suggested boxes in 'menuconfig', explored the capi4linux websites - etc... but am missing some magic. I've "modprobe

G'day, New to Asterisk alert! I have a Netjet card running on linux 2.4.27 kernel using the HiSax module, and trying to use it for incoming/outgoing calls from *. I've tried playing with modem.conf and extensions.conf every which way I can think of, using samples and whatever I can find off the net, and I get the same message everytime I try to dial in. The complete message is:

I had unexpected hangups from my asterix box using the i4l driver. (SIP <-> SIP calls worked execellent, but SIP<->ISDN didn't.) Then I changed the i4l driver in modem.conf with the chan_capi from jungham. (http://www.junghanns.net/asterisk) I followed his instructions in the INSTALL file, and first encountered some errors compiling it. It help by deinstalling several

Hello, I just got my isdn-card working together with i4l and asterisk. Everything seems to be working fine: I can accept calls coming from the outside and I can dial out. Even setting the msn works like charm but my problem is that I cannot hear a word. There's complete silence in both directions. Any idea what could be the cause? Thanks for your help, Gunther Lspci: 0000:01:07.0 Network

I need HELP pls! BRISTUFF: Bad Sound quality CAPI : PTP Mode dont supported mISDN : kernel is 2.4.x and not 2.6.x HISAX : PTMP ok, PTP incoming ok but in outgoing asterisk dont compose number(i listen dial tone and than i can compose number via dtmf) Asterisk CLI (g3 is group of Modem[i4l]/ttyI0 and ttyI1): Called g3: 3453444444

Hi all, Does anybody of you have the winbond w6692 working with the mISDN/chan_misdn.so? When loading chan_misdn.so from Asterisk, I get a "No lower Id port:1" error. The /var/log/messages file says: "MISDN free_device: entitylist not empty" I'm using Linux 2.6.11.11 + mISDN-CVS-2005-05-01 + Asterisk 1.0.7 + Zaptel 1.0.7 chan_misdn build from chan_misdn-beta-0.0.3-rc6

HI: Is there any way to raise up sound volume on fxo on TDM04B without changing tx-gain and rx-gain ? __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

Hello! Im pretty new of asterisk world: my goal would be using iaxcomm to call ppl over POTN. Yesterday i configured asterisk to be able to hear a song (with Playback() command) with iaxcomm, and it was wonderful. Now, today i tried to configure asterisk to use my ISDN4Linux supported card (a plain HFC card) with asterisk. i configured modem.conf this way, after reading

I have been trying to locate the patch that is supposed to cure the problem of hearing sound from the previous call when dialing through i4l and an hfc card. Does anyone have it? It is mentioned briefly in this post: http://lists.digium.com/pipermail/asterisk-users/2003-February/007530.html Thor

We have setup an asterisk box to let everybody call into the university internal network, but I get unexpected hangups when doing an outbound call from SIP to the ISDN interface, and it happens from 20 seconds to some minutes into the call. ----------the dial and the problem----------- -- Executing Dial("SIP/57966-a19d", "Modem/g1:96121||rt|") in new stack --

Hi, I'm trying to get asterisk running on kernel 2.4.20 however trawling through the archives I've found a few references to patches to remove i4l's dtmf detection, but have been unable to find the patch itself (I think it is isdn_audio.c). Can anyone point me in the right direction? The problem I'm seeing is connecting a SIP softphone (tried a few) to an external number via an

I have a ISDN BRI card with hisax module (w6692) and there is a lot of echo when I make calls to outside. Between the sip softphones the echo doesn't exist, but when I call to outside through the ISDN the echo exist. Is there any sense to put echocancellation in modem.conf ? ___________________________________________________ Nueva tecnología de Yahoo! Búsquedas ¿te atreves a comparar?

Hello, I am trying to use 2 netjet cards under asterisk and isdn4linux. I am having a hard time trying to get them to work in terms of dial out. Does anyone have a working config I could look at for even one card (tried that, not much luck either). When i dial out: -- Accepting AUTHENTICATED call from 172.16.11.2, requested format = 2, actual format = 2 -- Executing

Hi all, i have noticed that i can't hear a ring tone if i make a call from my TDM40B to a chan_modem_i4l endpoint. I had a look in the code from chan_modem_i4l and there is a function calling "i4l_handle_escape" that gives a AST_CONTROL_RINGING frame back. But this seems not work ...(or i4l is not signaling it ?) Til now i have used the Dail app like Dial, Zap/g1:XXXXXX|60|r so it

Hi all, I'm new to asterisk and not too knowledgeable on ISDN, so please be gentle :) I have a dual-channel Eicon Diehl Diva card in a Debian Woody box with kernel 2.4.27, connecting to a Telstra (Australia) Onramp Home Highway ISDN line. I'm pretty certain the card and line both work since they've been used in this machine for PPP before this (but with an older kernel with DoV

Hi all, i tried to write a call generator script. It generate i file like sample.call in ast src tree. But when i set the callerid and make a call over Modem[i4l] then the caller id is not set for the outgoing call. Is it impossible to set the callerid at this time for ttI devices? Thanks for help, Thomas. ******************************************* beroNet technologies GmbH Dipl.- Ing.

Greetings, today I'm recompiling asterisk on a new machine with the same isdn card (not the same model, the *SAME* card) using CVS downloaded yesterday night. When I try to start *, it gives me the error: [chan_modem.so] => (Generic Voice Modem Driver) == Parsing '/etc/asterisk/modem.conf': Found == Loading modem driver chan_modem_i4l.so => (ISDN4Linux Emulated Modem

-------- Original Message -------- Subject: Answer App hanging in I4L Date: Tue, 25 May 2004 13:49:50 +0530 From: Murali Krishnan <murali@bksys.co.in> Reply-To: ismk@myrealbox.com Organization: bk SYSTEMS (P) LTD., To: asterisk-users@lists.digium.com Hi, Anyone using ISDN4Linux (Eicon Diva Hisax ) card. If yes, please help me out. After configuring extension.conf and modem.conf I could