similar to: Unable to create ZAP channel - All circuits are busy

Hi, I have some problem to get this setup working. I have a CAC Channel Banl I, with FXO and an Asterisk box ( I am using Asterisk@Home 1.2) and I have a TE110p installed in this box. What I want to do is, just to be able to dial one of those lines that already are connected to the channel bank, and transfer that call through TE110p and Asterisk to a user agent somewhere through Internet.

Hi all, I've recentrly starting to play around with *, when all I wanted is to configure an fritz ISDN card with A@H. Currently I'm stuck at the phase of what do I do with capi after everything is installed. I'm trying to understand how to setup incoming and outgoing calls at A@H since I'm getting a bit lost with the default dial plan. It seems that * answers but disconnect

I'm having trouble getting outbound calls going with aah 1.3 and a tdm400p w/ 4 FXO. Incoming calls work fine, outbound I get this: -- Executing SetVar("SIP/231-af2b", "OUTNUM=6643955") in new stack -- Executing Cut("SIP/231-af2b", "custom=OUT_1|:|1") in new stack -- Executing GotoIf("SIP/231-af2b", "0?19") in new stack

I have an X100P clone hocked up to an analog line of my PRI. I can use it to dial out. but when I call the extension it answers and says "GOODBY" I have a Livevoip DID which successfuly rings to ext 202 I am using asterisk@home and through the AMP inface the line should ring to ext 202 Below are Asterisk Messages, Extensions.conf and Extensions_additional.conf Extensions.conf

hi i've configured a TE205P on asterisk at home this is my zaptel.conf span=1,0,0,ccs,hdb3,crc4,yellow span=2,0,0,ccs,hdb3,crc4,yellow bchan = 1-15, 17-31 dchan = 16 bchan = 32-46,48-62 dchan = 47 loadzone = it defaultzone = it and my zapata.conf signalling=pri_cpe ; pri_cpe = PRI slave ; pri_net = PRI master switchtype=national usecallerid=yes hidecallerid=no callwaiting=yes

Nik, Just curious - what is your telco setup? Do you have PRI with the specified D channels? You need to make sure that your telco is set up to have the D channels on 16 and 47. When you first start Asterisk, or when you log on to the CLI, do you ever see messages stating the B channels are successfully started? Let us know. -MC -----Original Message----- From:

Hi, I configured a pair of asterisk box, one of them (the first) ISDN connected to the PSTN. I configured an "integrated" dial plan, and I SIP connected the two pbx. No problems in dialing extensions defined in one of the two pbx from any pbx. My problem is this: How can I make the users logged in to the second pbx to dial an external number using the ISDN connection of the first ? I

Greetings *`s, I am manually creating call files and dropping them into /var/spool/asterisk/outgoing to be picked up by *. Presently, when I use local/internal parameters using SIP it works..ie I make an internal call from device to device. However, when I try dial an outside number which I have set up in a custom conf file, it bombs out with the following message :

Hello Guys, I'm somewhat of a newbie and am desperately seeking for some help... I've managed to get asterisk up and running on my server, and signed up with a broadvoice account... I'm having no problem dialing and communicating between extensions, but whenever anyone tries to call my broadvoice account, they are greeted by no ring or anything, but rather simply a direct to

Hi, I'm a newbie on * trying to setup an HFC card. I'm locked for many days getting the all-circuits-busy. And no idea what else to look for/how to diagnose. I'm in Spain, I've tried changing many parameters on zapata/zaptelcong with no luck, also NT & TE modes (honsetly, I've no idea what is). Any clue will be very much appreciated! I've installed *@home on my RH9,

Hi all, I have some problem to send a FAX to a given number. I use asterisk 1.2.18, on a openSUSE 10.2, i586 host. The FAX is sent out via an ISDN PRI interface, I'm in Germany, and the destination FAX devices are in Germany too, but in different areas, so I have to use a city prefix. I did set the pri device in debug mode, below are two calls, to two different FAX numbers, the first is

Just installed V 0.4 of asterisk@home Programmed up 3 sip budgetone extensions, they call call each other fine. Tried to dial '9' for an outside line through an X100P to a packet8 ATA but got 'all circuits are busy now'. Here is the console output. == Spawn extension (from-internal, h, 1) exited non-zero on 'SIP/30-8d25' -- Executing

Hi, We are using VOIP-SIP gateway to route outbound PSTN calls. Recently, I am getting == No one is available to answer at this time message, after making 5 SIP attempts (Retransmitting #5 (no NAT):), and the calls are going out through alternate Zap-trunk. I do not see any hit (sip-debug traffic) on the voip-gateway for the failed calls. Strange thing is that this is happening randomly,

Dear All, I have an asterisk server version 1.2.12.1 along with trixbox and I am having this nasty problem, I have a TE200P and have an E1 pri attached to it and zttool says it's OK, I have configured the whole 31 channels into one group as follow: Zapata-auto.conf: callerid=asreceived signalling=pri_cpe switchtype=euroisdn context=from-zaptel group=0 channel=>1-15,17-31

Hi All, I have searched the various post and not able to find the solution. I am using Asterisk 1.4.21.2 for outgoing calls. Earlier i used ZAP trunk and it works fine. Now i need to move to SIP trunk and configured the same. When i try from softphone i got error as "Call rejected" and in the asterisk i got error as

Hi, I use: Trixbox-2.2.4 FreePBX-2.3.1.0 Asterisk-1.2.17 BRIstuffed-0.3.0-PRE-1y-e Zaptel-1.2.19 ..with two ISDN cards, often but occasionally the dial out failed but is possible to receive external call. My zapata.conf conf is: [trunkgroups] [channels] language=it context=from-pstn signalling=bri_cpe_ptmp rxwink=300 pridialplan=unknown prilocaldialplan=local switchtype=euroisdn

Hi - I've recently bought a mediatrix 1204 and have had a complete nightmare getting it up and running with an asterisk@home setup. I know this isn't a mediatrix list but I'm at my wits end and the support with this product is atrocious. (mine was even shipped with firmware that was incompatible with the win32 software it came with so I wasted a day trying to work out why the SNMP

I have a problem calling a certain number from our PRI line. Calling the number from a separate PSTN phone works fine. The remote number seems to have some funny call redivert setup, when you call it, it answers immediately, makes some kind of beep and then starts to ring. Our PRI is in the UK from Telewest/NTL/Virgin Media and most outgoing calls work without a problem. The server is

I just inherited a Cisco 2621 with a VWIC-1MFT-T1 card in it. Can I make this thing into MGCP gateway or even a SIP gateway for asterisk? Seems like it should bee useful for something! I'm perfectly happy to do my homework, but also don't feel thee need to reinvent the wheel! So, links with relevant info would be appreciated. If there is a config for a 2621 being used as a gateway

Same thing here. I had this problem awhile ago and made this workaround. Going to another trunk does not work because they are answering and not sending a error code. If you are using AAH code then this waits 10 seconds on your Voip then times out and goes to PSTN. You can modify for your needs The pertinent line is 14 in macro-dialout-trunk I am going to clean it up and repost under my