similar to: Asterisk and Zyxel Prestige 2000W_v2

Hi all I have just got a P2000w and experience several problems. Hopefully there is someone out there that has got it working. I saw it on Cebit and the person demonstrating it there told me that it was connected to an Asterisk server on the stand -so it should work. Problem 1: it does not register correctly It get lots of messages like this: Jun 26 19:45:19 NOTICE[1107585968]: chan_sip.c:5630

Hi, Does anyone have suggestions hooking Zyxel Prestige 2002 to Asterisk? I have tested Zyxel Prestige with both supported codecs. Call with G.711 sounds very choppy and cracking. Almost can't understand a word. Today I installed G.729 support into Asterisk but unbearable voice quality remains. It's a little bit better though. I have tested that Zyxel ATA with some commercial SIP

Hi All, Today I got a couple of ZyXEL Prestige 2000W WiFi phones. I'm having a problem making SIP calls although I can receive calls just fine. When I try to make a call the phone makes some sound (like "bup bup bup bup bup bup beep beep") and then I just hear hissing background noise (not too loud - like comfort noise). I upgraded to the latest firmware on the phone - Wj.00.10

Hi, Has anyone tried the ZyXEL Prestige 2000W with * ? Is it worth the money ? Best regards Matthias -- _;\_ Matthias Cramer / mc322-ripe System & Network Manager /_. \ Dolphins Network Systems AG Phone +41-1-847'45'45 |/ -\ .) Libernstrasse 24 Fax +41-1-847'45'49 -'^`- \; CH-8112 Otelfingen

If you see a wj0011 version of firmware for Zyxel Prestige 2000W floating around (I found it in a German forum), KEEP AWAY. It completely trashed the wireless networking in my phone. -- ========================================== Rod Bacon Empowered Communications Ground Floor, 102 York St. South Melbourne Victoria, Australia. 3205 Phone: +613 99401600 Fax: +613 99401650 FWD: 512237

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, Anyone have any experience with either of these, I 'd appreciate some feedback? Plus it seems pretty easy to steal a connection with this. Zyxel Prestige 2000W WiSIP thanks, - -- Steve "They that would give up essential liberty for temporary safety deserve neither liberty nor safety." Benjamin

Does anybody have any experience with the ZyXEL Prestige 2000W? I am having problems with the line tear down when I call another extension. If nobody picks up at the other end when I hangup the 2000W, the other extension continues to ring. Is there any way to hangup a SIP call if there is no more traffic? Asterisk seems to think that there is still a connection open. This is pretty annoying

I've just seen this post: http://www.mail-archive.com/asterisk-users@lists.digium.com/msg41132.html and it took me back to play again with my dust collecting 2000W. Does anybody got DTMF to work? My sip.conf looks like this: [400] type=friend context=from-sip username=400 secret=verysecret disallow=all allow=g729 dtmfmode=rfc2833 host=dynamic nat=yes qualify=300 canreinvite=no My phone is

Hi, I'm trying to get a Zyxel P2000W (reportedly also sold as WiSIP by Pulver) to work with an asterisk box. The phone connects nicely to an external VoIP company (sipgate.de reportedly using asterisk themselves) but there is a strange problem with my asterisk: - Incoming calls via ISDN (chan_capi) to the Zyxel work perfectly. - Outgoing calls (capi/sip/iax) via asterisk are dialling out

Okay sorry for the empty message bodies earlier problem with Outlook, I guess is you have digital IDs as I do and they expire, even if you override the signature option it clears all sent text....windows...mmmmph.... Anyway, what I was trying to relay to the group was that ZyXEL has come out with a new Firmware (March 21, 2005) for the Prestige 2000W WiFi SIP Phone. In my opinion it has made

(I posted this note on http://www.voip-info.org/wiki-ZyXEL+P2000W+configuration too) I tried to put together comments that were asked for on the P2000W. These configs seem to work fine for a ZyXEL P2000W, thanks to Giles Scott for getting me started with it. DTMF keys work fine and are "read" correctly by Asterisk. It's important that you upgrade your phone to a modern version

Hi, I've got a Powerware Prestige 9 1kVA UPS that seems to not be working with nut. It's not in the current "supported hardware" list, but the old bcmxcp page lists it as being a UPS that speaks that protocol. I have the following in my ups.conf [powerware] driver = bcmxcp port = /dev/ttyS0 desc = "Powerware Prestige 9 EXT" baud_rate = 2400 And when I start the

Hi all, I've more-or-less got NUT 2.0.4 working with my Powerware Prestige 1000VA UPS (serial), but unfortunately NUT is flagging LOW_BATTERY continuously, which is a tad embarrassing when power fails ;-) The numbers from upsc blah at localhost seem reasonable: ambient.temperature: 24.5 battery.charge: 99 battery.runtime: 3999 battery.voltage: 69.2 driver.name: bcmxcp

---------- Forwarded message ---------- From: Tim Dawson <tadawson at tpcsvc.com> Date: Thu, Feb 13, 2014 at 12:07 AM Subject: Re: [Nut-upsuser] Powerware (Eaton) Prestige 9 UPS To: Charles Lepple <clepple at gmail.com> Charles - As a quick followup, the Prestige (both FW 2.13 and 3.09 - 2.x is pre-Eaton, 3.x post) reply to the topology block query thus: 3.064046

Hi Everyone, After a fair amount of faffing ive managed to get the 2000w working with asterisk for IP -> PSTN calls (i.e. get the phone to make and receive calls over our BT line). The final solution is to set up outgoing VoIP calls but I now know that without a SIP aware router I can think again! (damn you iptables!) In the mean time I'm trying to figure out why I can't get the

Has anyone experiences this please: - We were running a number of ZyXEL P662HW-61 routers at our sites and all traffic was being sent over IP-SEC VPN's between devices. When we moved to a new architecture, we got rid of the VPN links so that the SIP traffic was running directly through the routers. Each site uses Snom 360 devices with the latest firmware (v4). Ever since we did this, the

Knowing very little about Basic Rate ISDN and having spent the last couple of hours educating myself, I thought I would seek some more informed comment. Please go easy if this is blindingly obvious :) I have a ZyXEL Prestige 100 ISDN Router, a stand alone relic from when we used to access the Net via ISDN. It has an ISDN BRI input, a 10BaseT ethernet connector, an RS232 connector for

Hi guys, I'm using Zyxel Prestige 2602R, as router/SIP-ua with my architecture SER+Asterisk. Normally, everything is fine. In these days I'm experiencing some problems: some guests said me that, if he call everything is right, but if is called, he cannot hear the caller. Immediately, I though into an RTP-Proxy problem, but is not. Then I saw that message appear on the Asterisk CLI, during

Bob, Have you looked at any of the products by Zyxel? With QOS, VPN & wireless support they have: For ADSL: Prestige 652HW Firewall/Router: Zywall 10W & 30W I'll be honest, I havn't used any of these yet. We were looking for similar products to suuport our VOIP installs. We just ordered some demo units from Zyxel, we shoul have them later this week. I'll let you know

Hello, does NUT support Powerware Prestige EXT 1000VA / PowerWorks A30 models in smart mode? I don't see them mentioned in the compatibility list (only Powerware 3115 and 5119 are there, listed as supported only by the "genericups" driver). Is the protocol known to be compatible with any other, supported UPS types? Thanks, Marek