similar to: ZyXEL P662HW / SIP / Crashing

Hi all I have just got a P2000w and experience several problems. Hopefully there is someone out there that has got it working. I saw it on Cebit and the person demonstrating it there told me that it was connected to an Asterisk server on the stand -so it should work. Problem 1: it does not register correctly It get lots of messages like this: Jun 26 19:45:19 NOTICE[1107585968]: chan_sip.c:5630

Hi, Does anyone have suggestions hooking Zyxel Prestige 2002 to Asterisk? I have tested Zyxel Prestige with both supported codecs. Call with G.711 sounds very choppy and cracking. Almost can't understand a word. Today I installed G.729 support into Asterisk but unbearable voice quality remains. It's a little bit better though. I have tested that Zyxel ATA with some commercial SIP

Hi! Then I phone other phones with my Zyxel 2000W (WI-FI) it just hang up when I answer the phone I am ringing. It works fine if I call the 2000W from other phones. I have tried many sip settings. I use this now: [205] type=friend username=205 secret=passwd205 callerid="Zyxel" <205> host=dynamic context=local nat=yes canreinvite=no disallow=all allow=g729

I have a zyxel wifi phone and it works just great registering and callin on * but when it comes to menus it just not working (buttons dont change menus) . Anybody else have this problem? Need help. thanks. -------------- next part -------------- A non-text attachment was scrubbed... Name: Jim Van Eeckhoutte.vcf Type: text/x-vcard Size: 136 bytes Desc: not available Url :

If you see a wj0011 version of firmware for Zyxel Prestige 2000W floating around (I found it in a German forum), KEEP AWAY. It completely trashed the wireless networking in my phone. -- ========================================== Rod Bacon Empowered Communications Ground Floor, 102 York St. South Melbourne Victoria, Australia. 3205 Phone: +613 99401600 Fax: +613 99401650 FWD: 512237

Does anybody have any experience with the ZyXEL Prestige 2000W? I am having problems with the line tear down when I call another extension. If nobody picks up at the other end when I hangup the 2000W, the other extension continues to ring. Is there any way to hangup a SIP call if there is no more traffic? Asterisk seems to think that there is still a connection open. This is pretty annoying

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, Anyone have any experience with either of these, I 'd appreciate some feedback? Plus it seems pretty easy to steal a connection with this. Zyxel Prestige 2000W WiSIP thanks, - -- Steve "They that would give up essential liberty for temporary safety deserve neither liberty nor safety." Benjamin

Hi All, Today I got a couple of ZyXEL Prestige 2000W WiFi phones. I'm having a problem making SIP calls although I can receive calls just fine. When I try to make a call the phone makes some sound (like "bup bup bup bup bup bup beep beep") and then I just hear hissing background noise (not too loud - like comfort noise). I upgraded to the latest firmware on the phone - Wj.00.10

Hi, I am having an odd problem with one of our Zyxel P-2000W v2 wireless SIP phones. The phone can no longer receive calls. DND is not turned on and the phone has the exact same configuration as the other 2 phones (they each have unique extensions and such but all other settings are the same.) What can I do to debug this in the CLI. Nothing seems to shed any light on the problem. I am using

Hi, I'm trying to get a Zyxel P2000W (reportedly also sold as WiSIP by Pulver) to work with an asterisk box. The phone connects nicely to an external VoIP company (sipgate.de reportedly using asterisk themselves) but there is a strange problem with my asterisk: - Incoming calls via ISDN (chan_capi) to the Zyxel work perfectly. - Outgoing calls (capi/sip/iax) via asterisk are dialling out

(I posted this note on http://www.voip-info.org/wiki-ZyXEL+P2000W+configuration too) I tried to put together comments that were asked for on the P2000W. These configs seem to work fine for a ZyXEL P2000W, thanks to Giles Scott for getting me started with it. DTMF keys work fine and are "read" correctly by Asterisk. It's important that you upgrade your phone to a modern version

Hi, I know we've talked about this phone to death. I have pretty good voice quality, with and without WEP enabled, using the G729a codec and DLink & Netgear access points. I am facing one obstacle that is driving me insane. Does anyone have the call hold feature working? If you do... how did you make it work? The instructions say to press the left button to place the call on hold,

Hello. I am in a strange situation. I have two asterisk. Asterisk "A" makes a call for asterisk "B" by IAX. Asterisk "B" recives the call and delivers it to Openser by SIP. The problem is openser printing this in the screen: ERROR: parse_to : unexpected char ["] in status 5: <<"David" <sip:>> . ERROR:parse_from_header: bad from header

Hi Everyone, After a fair amount of faffing ive managed to get the 2000w working with asterisk for IP -> PSTN calls (i.e. get the phone to make and receive calls over our BT line). The final solution is to set up outgoing VoIP calls but I now know that without a SIP aware router I can think again! (damn you iptables!) In the mean time I'm trying to figure out why I can't get the

If your phones support PoE, I have had huge success with Zyxel: http://www.amazon.com/ZyXEL-ES1100-16P-16-Port-Ethernet-Unmanaged/dp/B00 5GRETMM/ref=sr_1_3?ie=UTF8&qid=1426296572&sr=8-3&keywords=zyxel+poe If you want to go even cheaper, I have successfully used these as well: http://www.amazon.com/TRENDnet-8-Port-100Mbps-Switch-TPE-S44/dp/B000QYEN

hi folks well, tinc is a really nice tool and we implemented it on 3 linux servers and 2 mobile clients (XP notebooks) so far. one of the 3 tinc servers is making troubles, when a connection is initiated from this server over a zyxel 642 adsl router out to the other 2 servers in the internet. the logfiles of the other 2 servers shows: > tinc[1398]: Received UDP packet from unknown

Does anyone know of any sip wifi phones? Only one i can find that is redily availiable is the zyxel prestige 2000w and from what i hear it is flaky. Kurt Fankhauser WaveLinc HYPERLINK "http://www.wavelinc.com/"www.wavelinc.com 114 S. Walnut St. Bucyrus, OH 44820 419-562-6405 -- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.300 / Virus Database:

Hi, Has anyone tried the ZyXEL Prestige 2000W with * ? Is it worth the money ? Best regards Matthias -- _;\_ Matthias Cramer / mc322-ripe System & Network Manager /_. \ Dolphins Network Systems AG Phone +41-1-847'45'45 |/ -\ .) Libernstrasse 24 Fax +41-1-847'45'49 -'^`- \; CH-8112 Otelfingen

Hi! I'm having a ZyXEL P2000W that I'm using together with my Asterisk box (CVS from some week ago). When I get a call directly to the *-box (lars@hostaname.domain.se) I see on the console that Asterisk get the calling users name as CIDName and his SIP-address as CIDNum - but at the P2000W i only get "asterisk" as CLIP? And I can see in the P2000W that "asterisk" is

Hi Has anybody tried to use the Zyxel Prestige 2000W_v2 with Asterisk? I have the latest firmware and can now make outbound calls. So it looks like Asterisk does accept the configuration in sip.conf. However, I cannot receive any calls. Also, I keep getting this message on the console: chan_sip.c:7733 handle_request: Registration from '<sip:51@10.99.1.133;user=phone>' failed for