similar to: Incoming / Outgoing call problems on TDM card.

The TDM01B is 4 port capable but has only 1 FXO module. I'm running asterisk 1.2.7 and zaptel 1.2.5. I cannot seem to get the TDM01B working. When I do the zttool it shows 4/1/0. I can dial out from a POTS phone up to the point that the cable plugs into the card. Here is my /etc/zaptel.conf loadzone=us fxsks=1 and here is my /etc/Zapata.conf [channels] language=en #include

Hi I am interested in setting up an Asterisk PBX in my office with digium hardware, and I just have a few questions in regards to what I would need. It is my understanding that an FXO card is used to interface with an incoming/outgoing phone line, and an FXS card is used for interfacing with a phone within the system. Currently we have 4 incoming/outgoing phone lines and would like to have

Hello all. Please, I'd like to know if somebody can help me with this problem. I have successfully configured a PBX with Asterisk 1.4 and a Digium analog card with 4 ports. This PBX has a lot of incoming and outgoing calls, and works perfect in general, but there are some extrange cases where an incoming call is bridget with an outgoing call, and the caller that is calling TO the PBX can

Hello, I am trying the setup the TDM01B card. 1 FXO. I connected it to a regular home line. in the /etc/zaptel.conf, I have fxsls=4 In the /etc/asterisk/zapata.conf I have: signaling=fxs_ls language=en group=1 context=default channel => 4 When I start asterisk, I get this error: ERROR[10376]: chan_zap.c:6584 mkintf; Signaling requested on channel 4 is FXO Loopstart but line is in FXS

Hi Everyone. I have a client that uses an Altigen system. I am really new to PBX systems so all this is totally foreign to me. They currently have 5 inbound trunk lines and about 20 analog phones. >From what I can gather they are using the Altigen Quantum cards that support 8 extensions and 4 trunks. >From what I can gather the solution is a TDM04B and TDM01B to bring in the lines from

Hi all, Your help would be greatly appreciated, I have been struggling for days with inst / config of TDM01B. I have installed TDM01B. Using Asterisk 1.2.9.1 on RH Ent 4.00 cat /proc/interrupts shows card wctdm on int 10. Green LED is on (module is in port 4). I have my /etc/zaptel.conf which includes fxsks=4 zttool show my card. ztcfg -vv shows my card. zap show status shows my card but I

Hi On an old IBM Netvista thinclient, the TDM card doesn't detect incoming calls, although the card seems to be detected, and correctly configured: pbx asterisk # lspci 00:03.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface # cat /etc/zaptel.conf fxsks=1 loadzone=fr defaultzone=fr # ztcfg -vv Zaptel Configuration ====================== Channel map: Channel

I'm trying to setup a demo where my Asterisk box with a TDM01B (FXO) answers an incoming call and forwards that call to a SIP softphone (X-lite.) Seems all is built/installed okay: # ztcfg -vv Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. I'm pretty new at this and the extensions.conf file is eating my

my target is to produce a linux router with T100p to Fract T1 24chan to ethernet and TDM 4channel FXO. I have not been able to get nethdlc to work, just get zaptel networking not configured if I set bchan and dchan the card comes to life, but I don't believe this is correct for what I want to accomplish. according to markster@ this is the way they do it. using (multiple distro versions

Dear list, We have an weird problem with our FXO card (TDM01B). When I made a call using this channel, all goes well, the called phone rings but when the called phone answers the call. In me handset I can hear an weird sound like a "Clack". I tryed diferents TDM cards and modules, and my zapata.conf is like, language=en context=from-zaptel switchtype=national usecallerid=yes

I have been experiencing a rather odd issue with my (newly connected) T100P card. It is installed in my Asterisk server, which is working great with SIP clients. The card is connected to a channelized T-1 line (24 channels). The odd bit is that outgoing calls (Asterisk --> T-1 --> PSTN) works just fine. However, incoming calls (PSTN --> T-1 --> Asterisk) are dropped after about 20

Hello, I have configured my TDM01B Card (1 FXO Port ) as follows (below) but it will not pick up an incoming call. Any suggestions/tools to see what the problem is? I have looked at zttool where this line changes but I don't understand what it means (The last digit changed from 0 to 1) Total/Conf/Act: 4/ 1/ 1 /etc/zaptel.conf fxsks=4 loadzone=nl defaultzone=nl

System: RHv9 cvs-head-11/23/04 with TDM04B and T100P (isdn pri). We've all seen many posts over the last several months regarding the stability of the TDM card. Today, the above system's TDM04B card (4 fxo ports) failed at approx 15:54:49. [root@asterisk asterisk]# cat /proc/zaptel/2 Span 2: WCTDM/0 "Wildcard TDM400P REV E/F Board 1" 25 WCTDM/0/0 FXSKS (In use)

Has anyone made spandsp to work with a digium tdm fxo card? I finally got the rxfax and txfax modules to compile, the spandsp lib installed (and in the libpath), and now receive: -- Starting simple switch on 'Zap/1-1' -- Executing RxFAX("Zap/1-1", "/var/fax.tif") in new stack -- Hungup 'Zap/1-1' I've tried to adjust rxgain/txgain in

Hi, sorry for my insistence but this is a big problem for me..my steps for remove card are ok ? Thanks. ------ Salvatore. ----- Original Message ----- From: "Sasa" <sasa at shoponweb.it> To: <asterisk-users at lists.digium.com> Sent: Monday, November 26, 2007 4:25 PM Subject: [asterisk-users] Remove a TDM Card > Hi, I would like remove a Digium TDM2400P from

FYI to the list.... I gave up (for now) trying to make spandsp work with the digium TDM card. Instead, I signed up with www.trustfax.com at a cost of $9.95 per year plus $.10/page. Since we only deal with an estimated 120 pages per year, the total cost of about $22/year seemed like a very reasonable alternative. (At least until we can find out why the TDM card does not function properly with

Hi Mary Christmas to y'all ! I am trying to configure * with one TDM and one ISDN and Bri-stuff, all is ok with only TDM but when add ISDN I get following error: I have tried to switch fxs/fxo but then I get error also without ISDN, card is configured from Digium with FXS(green) modules are closest to the bracket. ZT_CHANCONFIG failed on channel 1: Invalid argument (22) Did you forget

Hi: We are planning on using Digium TDM 24xx cards Does anyone know the fisical dimensions of the card in order to evaluate in which Servers the card fits??? Thank you Eugenio

I have a TDM-400 from digium with 2FXO+2FXS ports. Any idea on how much power will this drain from the 12 and 5 V connector when all ports are in use? -- Gustavo Felisberto (HumpBack) Web: http://dev.gentoo.org/~humpback Blog: http://blog.felisberto.net/ ------------ It's most certainly GNU/Linux, not Linux. Read more at http://www.gnu.org/gnu/why-gnu-linux.html . -------------

Hi All, I've installed digium TDM02B. The PSTN line connected to this card. At the IP network side, I have SIP phones registered sucessfully to asterisk server. How do I configure asterisk, so once there is incoming call to the TDM channel from PSTN, the caller will hear another dial tone from asterisk then to key in the extension of intended destination (SIP phones number) that already