similar to: TDM400P not detecting hangup and not hanging up

Can anyone suggest where I might begin looking for an answer please? I have just installed a TDM400P (2x FXS and 1x FXO modules installed) The first problem is that it does not seem to be able to detect if the remote party has hung up when a call comes through on the FXO. For example, if someone calls in, and then hangs up at any time after it starts ringing, Asterisk carries on as though the

Hi all, I have an existing panasonic analog pbx in use and a asterisk server with digium tdm400p(2 fxs and 2 fxo). channel 1 -> fxs -> telephone channel 2 -> fxs -> telephone channel 3 -> fxo -> extension 15 at panasonic pbx channel 4 -> fxo -> phone line from telco We call in to fxo (channel 4) and enter the ivr which prompt us to enter the extension number. After

I'm a complete Asterisk novice and have an installation based on the Asterisk@HomeCD. I've installed my TDM400P with 2 x FXO & 2 x FXS, but every time I try to dial out, I get a message "No circuits available". Can someone confirm the pinouts for connecting the FXO's to a UK BT Line - I have RJ11 connectors on the back of my TDM400P card, so ideally I'd like to

Hi I know this gets covered fairly regularly, but I've had a search through the archives and can't find anything dealing with this specifically - apologies if I've missed it though. I've got a TDM11B with the fxo port plugged into a standard UK BT PSTN line, loading wcfxs with OPERMODE=UK. All's working well, except if I get an incoming call through my bt line, and the

Hi All; If I need to set the opermode to King Saudi Arabia, what the name I have to use? For example, to set it for kuwait then I use opermode=KUWAIT. So what will be for Saudi Arabia? Any advise? Regards Bilal

We are in the process of preparing to move our Asterisk server to a Digital T1 interface card instead of a analog card (via an Adtran which is now connected to the T1). I did a preliminary test the other day and hooked the T1 line up to the T1 card, bypassing the Adtran. This worked rather well I must say. The two issues I ran into are: 1) Caller ID is not working even though I enabled

Hi, I'm not sure if I just missed something somewhere along the way, but I noticed while I was going through the CVS logs that there is an option in the wcfxs module to set an "opermode" - which apparently might help with echo issues around the globe (like the ones I'm seeing - some times). So I'd love to use it and give it a go. Apparently, there are some options that

Hello, I have recently purchased a TDM400P card with one FXO expansion card, and I'm having problems. The card does not pick up incoming calls. Asterisk detects the ringing line and rings various SIP phones as required. When a sip phone answers, the sip user hears nothing and the PSTN user continues to hear ringing. Here is the asterisk output for an incoming call:

Hello The Ubuntu Asterisk package doesn't install /etc/modprobe.d/dahdi.conf, so I was wondering where to put the following line: ======= options wctdm opermode=FRANCE ======= Should it be in /etc/dahdi/modules? ======= options wctdm opermode=FRANCE ======= Thank you.

Hi, Has anyone in australia got asterisk running on FreeBSD? how would i pass the opermode=AUSTRALIA parameter to the wcfxs.ko module as kldload doesnt let you pass parameters to the module like modprobe in Linux. I tried to get the sysctl variable using sysctl -a it might use but nothing applicable was visible.... i need to set the impedences to 600 ohms, can someone please advice me on

Hi guys, I spent a couple of hours in Google, but the problem appears to be uncommon, so I'd like to ask about it here. The problem is exactly the opposite to "Asterisk does not detect FXO hangup". In my case it's the Telco who does not appear to be detecting Asterisk's hangups. Telco is Telus in Vancouver, Canada. The setup is very simple - Telco -> FXO/TDM400p

I've searched the Wiki and this forum with little success. I have a TDM400P in my server which functions fine. Except it will continue ringing about 3 times after hangup. I.e. it's failing to detect the hangup tone. I was previously running a Sipura 3000 and had the same issue. After researching and some timely assistance I was able to determine the hangup tones applicable to

Hi I'm sorry for the my trivial quest. I Have asterisk 1.4 with TDM 400 with FXO and FXS, and works fine from several months. Now I want to connect a device to TDMFXS that want a ring frequecy of 25 hz to activate: i am italian, and usually the ring freq is 20 hz. The other time (I have used that device several times with other asterisk installation) I have modified /etc//modprobe.conf and

I am finding that I have to increase the txgain in zapata.conf to 8 when my X101P is connected to my BT phone line, otherwise people can hardly hear me. This then gives echo issues. Do other people have the same problem on BT lines. I was wondering if I should give BT a call and get them to increase the gain on the line. Strange though as the rxgain is OK and I don't have this problem with

Hi! The X100P is working - partly. I can make outgoing calls. But the card has got a problem detecting incoming calls. Even in verbose mode I don't see any hint that the card detects a call. At the moment I'm using the card behind my old ISDN telephone system. Could it be a problem with the line voltage? Can I adjust anything when loading the kernel module? Bye! Michael

Hi there, I'm experiencing an echo problem and dammed If I can sort it out. We're running Asterisk on Fedora Core 3 64bit, installed as per http://www.voip-info.org/wiki-Asterisk+Fedora+Core+3. These are the specs of the Machine ? 1 x AMD A64/3500+ CPU: Desktop Athlon64? Retail w/fan SKT 1 x Asus A8N-SLI Deluxe Athlon? 64 S939 NVIDIA nForce(r)4 SLI? PCI Express Req: 24pin ATX 1 x

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi!. I am having problems with getting asterisk to detect when someone hangs up. I have a TDM400P with one FXO module connected to my telco, and also a FXS-module connected to my phone. The FXS-module detects hangups just fine, but I can't get the FXO to detect them. I am pretty sure i have disconnect supervision on my phoneline since when I

I thought I had posted this, but I didn't see it in the archives, so I guess I hadn't. I've got FXS lines going to a legacy IVR. When I Dial into one of these lines and then hang up, FXS plays the Congestion tone until the IVR drops voltage. I would like the IVR to hang up sooner. I could do this by either making the IVR recognize the standard Congestion tone, or changing the

Hi Guys, I recently got a TDM400P 4 FXO for use in the UK, this at the time seemed like a good idea as I had good results with an X100P clone. Installation went great and call clarity is excellent no echo like I had on the clone card. My problems start with detecting hanging up the line. If a person calls into the system and speaks to me on a SIP phone when I hang up the call clears

On an Asterisk 1.2.12.1 system using a TDM400P with two FXO and two FXS modules, servicing two POTS lines: When dialing a number, such as a bank, or pharmacy, where it is required to enter a long series of numbers via the phone's keypad, an unexpected hangup occurs. The hangup does *not* occur when entering the numbers, as one might initially expect, but after the called end begins to