similar to: Slight OT: Multi WAN Router and SIP Calls

Hi all I need to use three 512 kbps aDSL internet connections, in a load-sharing, link-failover scenario. Presently I am using Ipcop with a single DSL. Now, I seem to have two options...one..an Edimax quad wan port adsl router, with firewalling and NAT and second install a minimal linux distro for routing...something on the lines of LARTC....and keep NATTING, IDS & Firewalling on the linux

You need a combination of iptables and iproute2 to do what you want = because routing is based on it's DESTINATION address and you need to route on = your SOURCE address so it uses a different route depending on which source = IP is in the packet.. Refer to this page which is sort of what you want BUT not exact. It'll = give you some ideas...

Dear all... I'm a Chinese and I don't think that my English is well . But I have a big problem in use IPTABLES . I've looked all the documents and FAQs , but I can't find a solution to solve my problem . At last I decide to ask you in my poor English ...^^|| I have a Linux server (Turbo Linux7.0 in kernel 2.4.9-3) to be my NAT server . I have make it running iptables-1.2.2-6 . It

Hi, I''m implementing a linux router with this characteristics: - Multiple adsl with each public ip''s - Multiple LAN ethernets (in a bridge). - Linux IGD I have successfully implemented de 2 first steps, the adsl balanced fine (multipath routing), and the clients bridge fine. My problem is how to use that with linux-igd. My LAN bridge has STP and is implemented for

Hello! I''ve got the following setup: ippp0 (isdn), ppp0 (adsl), eth1 (internal lan), eth0 (nic dedicated to the adsl modem) Firewall rules: Default 2.4. iptables (everything set to accept) except: iptables -t nat -A POSTROUTING -o ppp0 -j MASQUERADE iptables -t nat -A POSTROUTING -o ippp0 -j MASQUERADE Routing Table: Default gw is set to the ptp partner of ippp0 Problem: Packets

Is anybody using Asterisk with a dual WAN router (Xincom XC-DPG602, Hawking H2WR54G, Fortinet FortiGate-60, SonicWall etc) ? -- #Joseph

I have a CIDR block of IP addresses that I need to pass through to a WAN. I am trying to have a CentOS 5.2 basic install with 2 NICs be the router/gateway between the WAN and the public IP CIDR block. Has anyone done this? Other than turning on IP forwarding what did you have to do?

i apologize if this has been asked before, but things are too busy to preclude a full search of the list. i have both cable and dsl from the local providers here. due to wiring issues here, i''ve been forced to put the cable modem in one end of the house and the dsl modem in the other. the cable modem is firewalled off by a cisco pix 501 (192.168.2.12). the dsl modem is firewalled off

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: image/gif Size: 5049 bytes Desc: not available Url : http://lists.samba.org/archive/samba/attachments/19980820/3742f5aa/attachment.gif

Is tinc able to use multiple gateways for outgoing connections? Or is it restricted to the default gateway? In other words... If I have a branch office with a cable connection and a dsl connection, could it use both in an active/hot-standby fashion?

Hi, I am trying to get information on out-of-sequence packets being dropped on my load balanced multilink router. Can anyone give me any information on how best to log/track such packets? The router is based on Leaf Bering uClib 2.4 (kernel 2.4.26) The load balancing is being done using teql over a number of gre tunnels, each on a separate ethernet ADSL to a central box where the gre

Working on a multiwan script based on the page http://lartc.org/howto/lartc.rpdb.multiple-links.html You can find the script at http://pastie.org/859350 I'm trying to make sure that the logic is correct, and that it'll work I think it would, and ideas to make it a better script, feel free to throw them my way. Look forward to hearing from you. -------------- next part

Hi Here is a short description of my network: ppp0 (adsl) ppp1 (adsl) | | | | --------------------- | Router | | Firewall | | MASQUERAD | | DNAT | | | | eth0 | --------------------- | | | ---------------------- |

Hi, I'm running dovecot (1.1.7) deliver and sieve (1.1.5) on a Fedora 9 platform, using selinux targetet mode. Most of the mail deliveries goes well, but once deliver tried to copy the mail to the /tmp directory, which it seems it not allowed by selinux. I guess that deliver wants to sanitize the mail or something and therefore copies it to /tmp. Before I ask for selinux to allow this, I

Hi List, Does anyone know of a good dual wan router that can handle SIP well and can failover between connections if there is a SIP issue on one of the lines (meaning there still is a connection however there isnt enough bandwith or sip packets arent going thru etc.) ? Thanks. Dovid -------------- next part -------------- An HTML attachment was scrubbed... URL:

I have done the "definitive test" in my adsl line, using a real computer: * Without incoming traffic management, my dns can take about 30s or more to resolve a domain (when it resolve, sometimes it doesn''t) when my adsl line is saturated. So the queue of my ISP doesn''t give preference to the dns (at the reverse, is it seems penalyzed), But doing 3 paralell ftps (and

Hi List, New subscriber/lartc user here. Have read the entire lar&tc howto, alexy''s ip_cref, etc. and must say, this makes iptables seem downright *easy*. I''m trying to build a three-legged linux router (WAN/LAN/DMZ) and have had it more or less working with iptables but would like to learn layer2 routing with iproute2. I have an adsl/29 network and would like my

Hi all, I was wondering whether any of you have experience/info on Cable and/or ADSL modems that would come together with a SIP phone adaptor. What I am interested in is something that would plug directly into you ISP's cable (be it ethernet or adsl/phoneline), would combine a modem/router/nat such that on the other you could simply plug in your RJ-45 cable for your PC and a RJ-11 cable for

Hi! I''m studying load balancing and fault tolerance using multiple WAN interfaces. I follow the howto in http://www.ssi.bg/~ja/nano.txt but the problem is that faults detected are limited only in link between lan gateway and modem/router adsl, and none about adsl signal. Someone can tell me another howto about fault tolerance using a different method? (that solve my problem) I know

The X-lite client is installed behind an ADSL router and it seems the ISP also has a firewall supposedly protecting their ADSL customers blocking some netbios ports and non-critical. I can't make outbound calls but I can receive but before then I had to use the following in the account section in SIP.conf [2222] ... type=friend secret=xxxx host=dynamic ;dtmfmode=inband ;