similar to: Asterisk@Home: How to changed AMP User Login and Password

>From the command prompt type: help-aah This will give you a list of commands to change passwords. For example: Commands Descriptions ----------------------------------------------------------------------- config set the local time zone and keyboard type netconfig configure ethernet interface genzaptelconf autoconfig Zaptel

First encounter with * Just downloaded & installed aah-2.7 Started up AMP, but i can not find any reference towards isdn. I presume there has to be some configuration done for my Eicon-Diva-pro. Does aah actually support isdn-bri? On the mail-archive i found some references, but these are rather old ( they speak about the coming release of aah-2.1) aah-handbook (version 1.6) doesn't

Hi, Can anyone please point me in a direction as to how to set up these 2 pci cards with AAH 1.1? I have (am still) googling left, right & center - but haven't found a definitive guide yet. The centos based setup lacks any of the tools I know (insmod, modprobe ....) so it is time consuming just to even dig around the AAH box. There are no zaptel.conf files ....and on it goes. A

Hi can anyone help. I just updated my CentOS and ran the command rebuild_zaptel and genzaptelconf with a Reboot in between each step. Now I have no Zaptel devices (I used to have 3 FXO X100P Cards) Summary of what happens below: (Zaptel.conf contains no card info after running this command.) Many thanks in advance, Richard ---- STOPPING ASTERISK Disconnected from Asterisk server

Hi I've got a dell 2550 with an Eicon Diva server PRI card plugged into it. I can call out using the acopy2 test utility. I'm having trouble with asterisk making calls however... my capi.conf and modules.conf looks correct by the wiki instructions - does anyone have any advice on where to look ? I can attach conf files etc. if needed. Asterisk says it has 30 capi channels available,

Hi; I've got an AAH installation where a customer wants to install an active Eicon DIVA BRI card. AAH is built on Centos 3.5 which is currently at kernel 2.4.21.37. Support for Eicon active cards is built-in. I've debugged and run the A@H install-Eicondiva script but when I try to run divactrl load -c 1 -f ETSI -Debug I get a response : A: can't get card type for DIVA adapter

Has anyone been able to compile Zaptel after upgrading to 2.6.9-34.0.1.ELkernel? I'm running CentOS and was unable to recompile Zaptel. I reverted back to 2.6.9-22.0.1.EL but even then Zaptel would fail to load. I tried pulling the latest zaptel sources from digium cvs, but they apparently don't have a record in dns for cvs.digium.com. I did download zaptel-1.2.5.tar.gzand recompiled then

I would like to install a TDM04B with Asterisk@Home 2.4 and Asterisk@Home 1.5 but I didn't find documentation about this installation. Thanks in advance, Nelson -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060206/85ff5252/attachment.htm

Dear Asterisk developers, I run the same asterisk version on the home machine and on the work. On the home machine I have Slackware 10.0 (kernel 2.4.24) while on the work machine I have Mandrake 10.1 (kernel 2.6.8.1 <http://2.6.8.1>). When I run asterisk on the work machine, these warnings and error appear (there are no warnings or error at home): [ Booting......Oct 17 18:19:04

Hi all, What are the best and free tools for remotely adding, removing users on Asterisk server and also for monitoring the status of the Asterisk server, like how many users are logged on etc. I need tools for which I don't have to pay. Thanks, Zeeshan A Zakaria www.acabling.com <http://www.acabling.com/> -------------- next part -------------- An HTML attachment was

I know this subject has been beaten to death .. but I haven't been able to find a solution .. so here it is again: I can join the my Windows DOMAIN without issue. [djohns1@lmsprfc24208a djohns1]$ smbclient -L \\\\mspap01u added interface ip=192.168.240.53 bcast=192.168.240.255 nmask=255.255.255.0 added interface ip=192.168.131.1 bcast=192.168.131.255 nmask=255.255.255.0 Password: session

What kind of help do you need then? Regards, Jan -----Ursprungligt meddelande----- Fr?n: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] F?r Zach A Skickat: den 6 februari 2006 18:31 Till: 'Asterisk Users Mailing List - Non-Commercial Discussion' ?mne: RE: [Asterisk-Users] Help on queues There is no good help on wiki and voip-info.org, I've

I currently do this for about 30 different cisco 79xx's connecting to some hosted Asterisk servers. Asterisk listens by default for any SIP connection on UDP port 5060. And will use RTP UDP port 10000 to 20000 The phones use UDP Port 5061 for incoming connections (from Asterisks or other SIP Devices) and use for RTP, UDP port 10000 to 20000. Now, if you are going to have the two remote

Which models of Diva could work with CAPI and asterisk? Thanks Giordano ________________________________ Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Per conto di gw@adcomcorp.com Inviato: sabato 1 ottobre 2005 23.46 A: asterisk-users@lists.digium.com Oggetto: RE: [Asterisk-Users] Diva Nope. At least I tried and never could get it

Hi everybody After setting up trunk with FWD, all I get on my Asterisk box is message saying that all circuits are busy now, try your call later. Even 612 (time) says the same thing. Why is it that and how can I fix it. Zeeshan -------------- next part -------------- An HTML attachment was scrubbed... URL:

Erik de Castro Lopo <mle+cl <at> mega-nerd.com> writes: > > Hi all, > > I'm compiling current SVN HEAD on Linux/x86. The tests are failing > on PowerPC due to the following assertion failure : > > JITTests: PPCCodeEmitter.cpp:152: unsigned int<unnamed>::PPCCodeEmitter:: > getMachineOpValue(const llvm::MachineInstr&, const

Erik de Castro Lopo <mle+cl <at> mega-nerd.com> writes: > > Hi all, > > I'm compiling current SVN HEAD on Linux/x86. The tests are failing > on PowerPC due to the following assertion failure : > > JITTests: PPCCodeEmitter.cpp:152: unsigned int<unnamed>::PPCCodeEmitter:: > getMachineOpValue(const llvm::MachineInstr&, const

D. Johnson wrote: > I added build, host, target = ppc-unknown-linux-gnu and enabled libffi. One of > hese gets rid of the assert errors. I'm guessing the B,H,T addition. Confirmed. Configuring with: ./configure --host=ppc-unknown-linux-gnu --build=ppc-unknown-linux-gnu \ --target=ppc-unknown-linux-gnu passed all tests. > Configure script guessed ppc64. I

On Sun, 31 Oct 2010 13:31:58 +1100 Erik de Castro Lopo <mle+cl at mega-nerd.com> wrote: > D. Johnson wrote: > > > I added build, host, target = ppc-unknown-linux-gnu and enabled > > libffi. One of hese gets rid of the assert errors. I'm guessing the > > B,H,T addition. > > Confirmed. Configuring with: > > ./configure

Dale Johannesen wrote: > I'm not working on it, but I might be able to help find the problem. > What this means is that you're generating code in PIC mode, and an > object that requires a PIC register to reference is being addressed, > and no PIC register was allocated. The allocation was supposed to > happen in PPCDAGtoDAGISel::Select when the reference was processed,