Displaying 20 results from an estimated 11000 matches similar to: "HDLC on T1"
2004 May 14
2
Data through T1, nethdlc
Hello all,
My set up is a fractionated t1, with 1-6 voice channels, 21-24 data
channels. I have a t100P installed in a amd 1500 with 512meg.
Question:
In order to set up the data channels, is the following correct?
1) compile new kernel with generic hdlc support
2) compile hdlc from hq.pm.waw.pl/hdlc
3) uncomment KFLAGS+=DConfig_ZAPATA_NET in zaptel makefile
4) compile zaptel,
5 compile rest
2004 Dec 08
5
Asterisk Maintenance
I went on a service call yesterday to find an asterisk system with a
T100P card on a Qwest PRI and a TDM40B card connected to fax machines.
The TDM40B LEDs were not lit, and the system did not respond to keyboard
input. However, calls were being processed for the PRI and 7960 phones.
I replaced the TDM40B card with a new one, and the system now seems to
be ok. But I'm wondering, why
2004 Apr 10
4
Woodpeckers Revisited
Just when I thought I couldn't be wrong, I was wrong. We have
woodpeckers that drill into the arial telephone cables, and water seeps
through the holes and partially grounds the tip and/or ring wires
causing hum. I thought the hum/buz on my lines was a telco problem.
The Qwest HQ noise team assures me that my lines are within spec. Sure
enough, when I listen on the test set the lines
2005 Jul 08
3
McLeod Integrated T1 - no PRI?
Hello everyone,
We have recently turned up a new T1 from McLeod (Midwestern CLEC). It
is configured like so:
/etc/zaptel.conf:
loadzone=us
defaultzone=us
span=1,0,0,esf,b8zs ;(also tried 1,1,0,esf,b8zs)
bchan=13-23
nethdlc=1-12
dchan=24
/etc/zapata.conf:
switchtype=national
context=pri-in
signalling=pri_cpe
group=1
channel => 13-23
I can get hdlc0 (and pvc0) up just fine after the
2006 Nov 16
1
Sangoma A101 gives 'no PRI configured on span 1' error
I upgraded from Tormenta2 to Sangoma A101. I followed the instructions, and
installation was successful. zttool, ztcfg, all show card is installed
properly. I copied the parameters from my old working zaptel.conf,
zapata.conf and zapata-auto.conf. Verified on Sangoma website that these
files are correct. Also configured wanpipe1.conf.
But doing all this didn't start the PRI channels. It says
2003 Dec 02
4
Configuring new system for a non-profit organization
Hi,
The PBX at the Colorado Organization for Victims' Assistance fried as a
result of the building power being cycled. I'm now in the process of
building an * system to replace the failed PBX. Minimum cost is the
priority.
I have a T100P card installed in the new system, and I am about to order
integrated T1 services from the "CBeyond" company. They will require
eight
2004 Mar 31
1
Voicemail prompts garbled
I'm having problems with the voicemail prompts. The beginning of each
prompt is garbled. Prompts "edian mail" and "assword" can be
recognized, but when it starts on the short phrases it is completely
garbled. It is almost like the subsequent phrase starts before the
current phrase finishes.
I have isolated the LAN to the * box and the phones, so LAN congestion
is
2004 May 21
5
T100P HDLC configuration
All,
I am trying to configure hdlc support on T100P Digium card - everything
seems ok... but it just does not work at all.
I was able to compile all drivers, the light on the card becomes green
when I plug T1 link.... but I even can't ping default router IP... there
is no data coming back to me, so I am confused completely now.
Also I tried both protocols - raw hdlc and cisco hdlc. The
2004 Apr 10
1
Hum/bux on line
Rich Hi,
After Qwest pronounced my circuits as within spec. (yes, disconnected
from the house) I listened on the lines with my butt set. Clear of all
noise and hum. I then got my box of Cat3 and laid a circuit around the
outside of the house and into my lab. Still clear of all noise and hum.
I then connected the circuit to the Adtran and made a call. Lots of
hum and buzzz.
As I said,
2004 May 30
1
Fwd: hdlc and kernel 2.4.26
Hello,
I contacted Krzysztof Halasa, the maintainer of the current sethdlc
code. This is the response he gave me.
Of course, I have this working now. Still some minor configuration to
do, but It does work, and the connections to the internet are _much_
faster than when I went through the adtran... I would highly recommend
to anyone with a fractionated T1, with data and voice channels to
2003 Nov 19
8
Help please
Hi,
My PBX/key system failed when building power was switched off and then
back on. The service rep says the PBX unit is so old that it is not
repairable.
The unit has 8 incoming POTS lines and 12 multiline sets. There are
voice mailboxes on each line.
Switching to Qwest's Centrex system would cost about $3800/yr. My 8
business lines now cost $3320/yr, so the Centrex increment would
2004 Dec 21
1
zaptel ppp HDLC Receiver Overrun messages
I have a pair of sites tied together with a T1 line running zaptel PPP
on either end. The system works, but I keep getting these messages in
the kernel logs, and users are reporting connection problems (TCP
timeouts, and hangs) especially under high usage.
--snip--
HDLC Receiver overrun on channel WCT1/0/1 (master=WCT1/0/1)
HDLC Receiver overrun on channel WCT1/0/1 (master=WCT1/0/1)
HDLC
2005 Jul 04
1
HDLC bad FCS
I have 2 servers, configured identically. Each has a TE405P and 2 PRIs. One server was experiencing crackly audio on one circuit, accompanied by HDLC
bad FCS messages. The telco recabled and moved me to another port on the DMS-100. The audio is better, but there are still bad FCS problems on the
span. I have moved the PRI in question to the other server, and the problem does indeed move with the
2005 Jun 23
1
HDLC abort 6 error
I've read as much as I can on this error and still can't seem to figure
out what's causing this error:
Jun 23 20:54:58 NOTICE[7483]: chan_zap.c:7395 pri_dchannel: PRI got event:
HDLC Abort (6) on Primary D-channel of span 1
Jun 23 20:55:03 NOTICE[7483]: chan_zap.c:7395 pri_dchannel: PRI got event:
HDLC Abort (6) on Primary D-channel of span 1
Jun 23 20:55:03 NOTICE[7483]:
2005 Aug 23
8
HDLC/Zaptel/Kernel 2.6.11(.9)
All,
I'm having a heck of a time getting hdlc to work on kernel
2.6.11.9 .. I compiled hdlc, hdlc_gen, hdlc_cisco, hdlc_raw, into the
kernel (note into, and not 'modules').
System comes up, I configured zaptel.conf
span=1,0,0,esf,b8zs
nethdlc=1-24
modprobe wct4xxp
ztcfg
sethdlc hdlc0 cisco
ifconfig hdlc0 up
All of this works fine, believe it or not. I have a T1 cross plugged
2006 Jun 03
3
Sangoma A101 configuration
Im trying to install and configure sangoma ...
every thing is OK but when type the command "wanrouter
start" the following error apears:
wan Driver not found.
Thanks for any help
2007 Jan 25
2
TE110P and HDLC problems
Hi!,
this issue makes me crazy. I read a lot of docs, also * mailling list
and I try a lot of things without success.
Any help will be appreciated. Here is the info:
Hardware:
--------------------------------------------
Supermicro Server with motherboard X7DB8, chipset Intel 5000P, Xeon 5050
Digium TE110P
Software
---------------------------------------------
Asterisk version 1.2.12.1
2010 May 31
1
Suddenly "HDLC Bad FCS (8)" errors on ISDN-PRI, changed nothing
Hi fellow asterisk users,
I am running Asterisk 1.4.29 with an Digium TE121 card (wcte12xp kernel
module) an approx. 100 snom320. The whole installation is running
without issues since 5 months.
Without having changed anything on the asterisk server for at least 2
months, i noticed "clicking sounds" at external calls over the PRI.
Asterisk constantly throws the following messages:
...
2005 May 25
7
zaphfc: empty HDLC frame or bad CRC received
Hi, i've downloaded/compiled/installed the bristuffed asterisk
Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a
and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine
with kernel 2.6.11. Asterisk works well if i configure the card using
isdn4linux.
I'm having problems dialing out (not tried the input yet).
This is the output from asterisk:
-- Accepting AUTHENTICATED call from
2010 Nov 27
1
DAHDI 2.4.0 produces HDLC errors with echo canceler
Hi,
After upgrading to DAHDI 2.4.0 from Zaptel, I noticed a lot of HDLC
errors on my console:
[Nov 27 01:15:09] NOTICE[2743] chan_dahdi.c: PRI got event: HDLC Bad
FCS (8) on Primary D-channel of span 1
[Nov 27 01:15:09] NOTICE[2743] chan_dahdi.c: PRI got event: HDLC Abort
(6) on Primary D-channel of span 1
These errors prevented calls from being made and received on my PRI spans.
This seems