Displaying 20 results from an estimated 8000 matches similar to: "AT-320 IAX & MWI?"
2006 Jun 07
1
MWI on the PA168V in IAX mode?
I've gotten nothing from http://bbs.atcom.cn on this so far. Perhaps
someone on the list has experience with this.
Is there a way to get MWI support for PA168V-based ATAs? Apparently
some IP phones based on the PA168V chip has this support already
(Atcom AT-320 for example) by configuring Asterisk with
'mailboxdetails=yes' in iax.conf. On my ATA, however, it does nothing.
Any
2006 Dec 22
2
UPDATE - Analog Phones with FSK/Stutter MWI
After purchasing the Uniden TRU9480 and then the Panansonic 5672, both of
which do not have "phone company" compatible FSK/stutter MWI, I finally
got smart and found out just which Panasonic phones have this feature.
Only the following 5.8G models in their current line have FXO compatible
MWI. I purchased the 5771 unit and one remote. I have confimed it does in
fact work with Asterisk
2007 May 21
3
Aastra MWI
I need to setup MWI on a few Aastra 9112's. I've tried doing so in the
web interface by setting "Explicit MWI Subscription" to true, but no
lights, no stutter tone.
Firmware: 1.4.0.1048
Thanks!
--
Warm Regards,
Lee
2009 Sep 01
2
1.6.1 + TDM840 FSK MWI problem
Hi,
Using 1.4.26.1 & DAHDI 2.2.0.2, FSK VMWI devices off a TDM840 work fine.
With 1.6.1.[45] & same DAHDI, instead of the FSK spill I get a line
polarity reversal. Stutter dialtone is generated as expected.
Has anyone else seen this? Is there anything special I need to do for
1.6.1 to make FSK MWI work?
Thanks,
--Barry
2005 Jan 13
1
MWI on Zap analog phone not lighting
We are using Bellsouth 8867 phones on our TDM400B FXS lines
(asterisk-1.0.3). It has a "Voicemail" light, which appears to be MWI
(according to the manual it works with voicemail from the telco that
sends a FSK signal). The dialtone stutters when a line has voicemail, so
I know that I have the mailbox setting right in zapata.conf, but the
light doesn't go on. I am also getting
2003 Sep 08
3
Adtran TA750 MWI problem
I recently set up Asterisk with an Adtran TA750. All
is well except the phones do not show the MWI.
I have configured zapata.conf properly, as all phones
will receive a stutter dial tone if there is a message
waiting in it's assigned mailbox.
Does anybody know how I might fix this problem?
Thank you for your time
__________________________________
Do you Yahoo!?
Yahoo! SiteBuilder - Free,
2003 Nov 03
2
MWI - I know this has been discussed in depth already
Let post this question.. Because I must be real slow... The following is
my config on this...
group=1
context=default
signalling=fxs_ks
channel => 1
context=local
signalling=fxo_ks
callwaiting=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
echocancel=yes
echocancelwhenbridged=yes
relaxdtmf=yes
rxgain=1.5
txgain=1.5
immediate=no
musiconhold=default
usecallerid=yes
2005 Sep 19
2
MWI indicator HINT on Snom thru IAX?
I have many remote locations that dial into a central server to retrieve
voicemail via IAX. Outbound calls are handled as SIP calls from a Snom to a
local (to them) Asterisk server that dials the main server thru IAX. I have
trained them to check their voicemail via the emailed WAV file, however some
of them are, how shall I put it, idiots*, and insist that they *have* to
have the MWI indicator
2005 Jan 12
5
Grandstream Bugetone 101 & mwi
I tried to use message waiting indicator, by "Subscribe for MWI" in the
web menu of the phone.
However, it does not light up / flash, even if a voice mail is waiting.
Where is the switch to turn it to?
bye
Ronald
2009 May 25
1
Placing a MWI on-off call...
My grateful thanks to whoever can guide me in implementing this...
I have a need to place calls via Asterisk Manager Protocol to a legacy PBX
and twiddle its MWI lights.
By some means I get notified that an MWI light has to be changed.
Via AMP:
1. Send an ORIGINATE command honking up an incoming port on the PBX via a
TA804.
a. I presume that the TA804 should be a SIP channel. yes/no?
b.
2005 Jan 18
4
sipura 3000 mwi stutter problem
May be I have fiddled too much with my sipura settings but I can't get it to
give the stutter tone when there is a new voice mail waiting on the asterisk
box. I can either get a stutter tone all the time or not at all. Anyone
got this working.
Thanks
Chris
2005 Jun 30
7
passing through MWI info from SBC
Hi.. I am about to replace my aging Nortel Venture
system with an Asterisk system and 6 Polycom IP 501
phones, and a couple sipura 841's for less used areas.
We have 3 phone lines here. One is SBC, one Vonage,
and one Voipjet... One hangup is that I can't figure
out how to pass through a voicemail waiting indication
from SBC. This is important because my wife and her
family all
2004 Dec 20
3
grandstream MWI?
Hello,
it is possible to get MWI working with Grandstream and Asterisk?
Thanks.
-David
2006 Dec 08
2
5.8gig phone MWI
Does anyone have personal experience with a 5.8gig wireless phone (system)
that has an MWI that WORKS with asterisk via fxs (in my case spa3k)
generated MWI. I know the spa3k does stuttered dialtone but not sure if it
generates FSK MWI.
I see some that state they do but I also see reviews that say they don't.
Doug
2005 Jan 14
1
Re: Budgetone and MWI
asterisk-users-request@lists.digium.com is believed to have said:
>I don't mean to be rude to everyone who responded to this question, but
>I think that everyone is answering the wrong question. The point is that
>the message waiting indicator doesn't light up, at all, ever. All that
>happens when messages are waiting is that the display blinks and the
>phone gives a
2005 Aug 08
4
Multiple MWI on a single phone?
Hey all...I'm trying to find a phone that will support multiple MWI so
that I can have a shared central phone with say 4 users who can see
visually that hey have messages waiting. Is there any phone that will do
this possibly by re-assigning a soft-button? Can the Polycoms do this
since those seem to be the phone of choice these days?
Thanks!
2004 Jun 12
5
MWI on Cisco ATA-186 (SIP)
I am trying to set up the Message Waiting Indicator (stutter
tone/light) so that my cisco ata-186 will let my phones know there is a
message waiting. However this does not seem to be very well
documented.
I found this on wiki mailboxnumber@context ... where does that go? Do
I put it in my SIP.conf definition for my cisco ata, or where. In my
SIP cisco definition i already have a
2003 Jun 09
1
Adding an app
I am in the process of testing out the Cisco ATA 186 to provide analog
phone service via VoIP for some of our remote users. I have that working
fine and well, but am struggling with another aspect. We already have a
large centralized voicemail system, which I would like to use for these
users. I can get the call to roll to new the centralized voicemail no
problem, but I'd like to provide
2003 Oct 20
2
Message Indicator Light
I have a quick question...
In the previous thread
http://www.marko.net/asterisk/archives/0210/0306.html it is mentioned
Mark added support for MWI to the chan_zap. Is this in the zapata.conf
and if so, if stutter is turned on then the MWI is turned on with it?
Geoff
2003 Jun 10
1
Re: Adding an app (Steven Critchfield)
Thanks for the help. I was able to get my application to load with
Asterisk, now I just need to get it to work. After reading your comment, I
don't know that I fully understand what's going on as far as the channels
and extensions. Are you saying that the MWI is tied to the channel? If
that is the case, then for my SIP phones, would the channel be (SIP/XXXX)?
If it should be, then