similar to: Fax to email using mime-contruct

I also want to try that asterisk guide. But i'm not sure if i understood it correctly. What exactly do i need to do? Do i need to compile Asterisk with the spanDSP plugin or just configure extensions.conf? The URL to spanDSP in the guide wasn't working. I also use a traditional internet line to recieve calls and hopefully i will get Fax working soon. This is so confusing. Thanks, Arne

I'm trying to install the SPANDSP software into Asterisk to support incoming (mainly) Fax. I'm following the info in http://www.voip-info.org/wiki-Asterisk+Fax. I downloaded and installed the spandsp software from ftp://ftp.opencall.org/pub/spandsp/ and followed the directions in several documents listed on the on the Tiki page. I get down to patch < Makefile.patch that fails with

We've managed to setup spandsp to receive faxes and email them to the appropriate person. We did all of our testing using Thunderbird, and the attached pdf files worked very well. However, when we went "live", some people complained that the attachments in outlook were named <<subject>>.dat instead (for example) of 123456.pdf Having looked into the mime-construct

is it possible to achive the following scenario? faxmachine--tdm40bFXS--SIPnetwork--Gateway--faxmachine i have found a lot of documents about asterisk receiving a fax and saving it to a file. But i want to receive the fax via SIP and send it to my faxmachine. I also want to send a fax from my faxmachine through the digium card, so asterisk should send the fax via SIP to the gateway, which also

what causes ''em? How do I spot ''em? How can I fix them? I''ve got several apps running on textdrive, and they''re all consuming too much memory and being killed all the time. I''m still a relative n00b to Rails, and not sure how to go about fixing them. When I look in the dev/production logs, I don''t see any obvious errors in my code, so what

Hi all!....i'm in course to implement Faxing in my asterisk box and for that I've installed all succesfully like libtiff and spandsp and next rebuild and reinstall asterisk modules, but when i call to Rxfax from dialplan nothing happens and i get some errors like "XCN with final frame tag In state 9" or a paper copy of a transmision report from the fax machine with COMMUNICATION

Using 1.6 on Fedora Core 9 I'm trying to receive faxes. I've got this far: [incoming-fax] exten => s,1,Set(FAXFILE=/var/spool/asterisk/fax/${STRFTIME(${EPOCH},,%Y%m%d%H%M)}-0${CALLERIDNUM}) exten => s,2,ReceiveFAX(${FAXFILE}.tif) exten => s,3,Hangup() exten=>h,1,System(/usr/local/bin/fax2mail --cid-number "0${CALLERIDNUM}" --cid-name "home fax"

>>> kurtwp@yahoo.com 6/15/2004 7:29:33 AM >>> >Old managers will change its the LaLawyershat don't >change. Every dam law office that I been in has at >least one fax machine that is constantly printing >something out. But to say fax is dead is an >understatement. >AT&T said that about teletype service, you know 50 - >300 baud service, years ago and

i sent a product suggestion to HP. It was a request to use software that already exists in their JetDirect and Multifunction Fax machines to make them seamlessly interoperate with a fax gateway in a way transparent to the end user. Essentially, giving the sysadmin a choice in fax transport mechanism to route all faxes over analog telephone transport or over the network. Thank you for taking

Is the X100P FXO PCI Card capable of detecting a fax, answering the call, and then emailing the fax content to an email address? Thanks. Paul.

After searching the archives, I came acrross a few people mentioning this, but I never saw anything about what became of it. Has anyone tried to make a virtual modem that could be directly handled by astrisk, I saw a while ago that someone was going to try and make one using the same DSP libaries that the WinModems use, but then nothing. Would do this even be possible, and if so, what kind of

Hello, I tried the above setups and am having large problems sending and receiving faxes, even in very low speeds (9600 and far below). Faxes are either shifted (i.e. missing lines) or corrupt at all, some faxes do break with communication errors (although CRC-alike algorithms are turned off) or in alot of cases only the upper quarter or 1/8 is transferred. Iam seeking for any idea on how to

I'm really trying to understand this. I have a Sipura 2000, brother MFC, and SpanDSP set up on asterisk. because asterisk softfax was not working well, i set up faxes to goto line2 on the sipura. this is working fine, i have only tested a few short faxes, but already my completion rate was 100% vs 5-10% that spandsp and asterisk gave me. here's the odd part. using the fax machine, I

Thanks James, What i need is to make the fax machines connected to the audiocodes mediant 1000 be able to send and receive fax throught Asterisk (connected to a pri) I know it's not reliable, but it should work at leaste, what should i do on Asterisk and Mediant to make this work? Im quite confuse with all these fax issues :S Thanks in advance > > Message: 11 > Date: Fri, 9 Apr

I've just made an interesting observation that I'd like to share with you all: the popular Sipura SPA-2100 just doesn't seem to be as great as I'd hoped. I've been trying to get inbound AND outbound faxing working via Asterisk and at least one of my termination services: Voicepulse or Sixtel. In general, inbound has been working flawlessly but outbound has been pretty

Good day all I have a pri card,e100 What I want to do is If a fax comes in for number 1234567890 it should be e-mail to user1@domain.co.za If a fax comes in for number 0987654321 it should be e-mail to user2@domain.co.za ens.... Can this be done and how????

I've read about Fax to Email, but is there such a beast as email to fax? If not, what do people use to take care of outbound faxing?

I've already search in the mailing list and voip-wiki site but I can not find any examples in how to send a FAX through a IAX channel. I've found the fax extention setting, but this is not what I want to do. I'd like to dial from the line on the other side of the IAX channel to a fax, to cut long distance costs, and send a FAX from the source IAX channel. Like bellow:

I'm unable to get faxes working over tdm400p (4fxs modules) Too many errors sending and receiving faxes with an analog fax 1) echocancel=no on the zap channels 2) ztmonitored the channel for a good/low audio volume I'm trying to send fax between zap fxs channels. No way to get it working right Has someone else the same problem?

Hello, in our company we are trying to do this: Fax <--> Traditional PBX <--> Asterisk <--> PSTN In practice, we have put an Asterisk equipped with a Sangoma A102 (2 PRI ports) between our PBX (Siemens HiCom) and the PSTN in order to have a VoIP network along the traditional telephony network. The problem is with the fax. We just want to send and receive faxes from/to our fax