similar to: Meetme using ztdummy on Linux 2.6 sounds scratchy

Hello System: Debian etch with kernel 2.6.18-4-686 or 2.6.18 custom. Asterisk Version: SVN-branch-1.4-r55483M Zaptel Version: SVN-branch-1.4-r2302 modules all ok in compilation time. And modules loaded: ztdummy 5928 0 rtc 13364 1 ztdummy zaptel 181540 1 ztdummy crc_ccitt 3200 1 zaptel In /dev/zap directory I have:

I'm running into a bit of a problem setting up conference calls. The box I rent at a colo doesn't seem to have USB hardware.... When I try to load usb-uhci I receive a "device does not exist" error. Which means I can't load ztdummy.... The system has a rtc clock module, so zaprtc won't work... (which I'm scared to unload rtc because I don't have physical access

I ran in to an almost impossible ability to run MeetMe on our poweredge. Our PE is a 4 proc with OHCI and we had no need to buy any PCI cards other than for running MeetMe. If you know how to recompile your kernel, recompile it and make RTC a module (its compiled in by default). Then you can use zaprtc as your timing source. Be sure to `rmmod rtc` before you `insmod zaprtc` because zaprtc is a

I have ztdummy installed: Module Size Used by ztdummy 3464 0 zaptel 218756 1 ztdummy crc_ccitt 2176 1 zaptel ohci_hcd 16388 0 floppy 49028 0 pcspkr 2180 0 piix 8580 0 [permanent] ehci_hcd 24456 0 uhci_hcd 26256 0 rtc

> output of zttest: > Opened pseudo zap interface, measuring accuracy... > 99.938965% 99.951172% 99.938965% 99.963379% 99.963379% 99.951172% > 99.951172% Ah. Don't be scared. This is actually -correct- when using RTC. Let me demonstrate: [root@dhcp5 zaptel]# ./zttest -v Opened pseudo zap interface, measuring accuracy... 8192 samples in 8195 sample intervals 99.963379% 8192

Hi, when I build zaptel-1.2 and asterisk-1.2 I can modprobe ztdummy and start asterisk to be able to use MeetMe(). When I build zaptel-1.4 and asterisk-1.4 I can modprobe ztdummy and start asterisk but I am not able to use MeetMe(). What do I miss? Stefan -- amooma GmbH - Bachstr. 126 - 56566 Neuwied - http://www.amooma.de Let's use IT to solve problems and not to create new

Hi, I've managed to build the zaptel modules including ztdummy; ztdummy is installing fine in the modules list and the relevant device structures are present. lsmod | grep ztdummy gives:- ztdummy 5160 0 zaptel 186916 1 ztdummy rtc 12372 1 ztdummy Where I'm stuck is I am now at a loss as to how to configure my /etc/zaptel.conf and

Any thoughts on the following? I am running asterisk from CVS (downloaded yesterday's version, just to be sure) on a test system with no digium cards in it, so I have installed ztdummy (see logs and screenshots below) as a timing source. When I call the music on hold extension from a Sipura Sip connected analog phone, I hear nothing and start getting Warning[98310]: chan_sip.c:674

Hi, I know this question may have been asked before (although the archives don't seem to suggest it), but has anyone had any problems with Asterisk accepting a PIN number for a conference room. At this point in time I have established the conference definition in the meetme.conf file as well as specifying the appropriate lines in the extensions.conf file. meetme.conf file: conf =>

On Thu, 2004-01-15 at 19:18, dkwok@iware.com.au wrote: >> I do not have any zaptel hardware on the Asterisk box, I could not have >> meetme functioning. I did modify the Makefile in zaptel directory on >> line 168 by including ztdummy as one of the modules to compile in. try modprobe ztdummy This works. Should I include this in /etc/asterisk/modules.conf so that it will

Hello, Today we setted up a server that needs to use MeetMe but doesn't have any Zap hardware. So we need to use ztdummy (at least, this was our idea). Rarely: zttest is not working at all (100% bad, using zttest -v doesn't give anything, etc.). Of course, after load ztdummy, there isn't any background or anything. It is the same kernel (Debian Etch default kernel, 2.6.18) than

When I call meetme: exten => 1000,1,Answer exten => 1000,n,Meetme(|||d) Asterisk is complaing with: -- Executing Answer("IAX2/xxx.yyy.142.204:4569-2", "") in new stack -- Executing MeetMe("IAX2/xxx.yyy.142.204:4569-2", "|||d") in new stack -- Playing 'conf-getconfno' (language 'en') Warning, flexible rate not

Have anyone experienced mixed meetme conferences? Im running a 12 seat call center outbound only. Asterisk 1.2.8, SIP/ulaw at the phones, SIP/ulaw to the SIP terminator. Machine: pentium Dual core 2.0ghz (533 fsb) , 1 GB RAM (533mhz ddr) , 2 SATA 80GB DISK in RAID 0 via software RAID driver. Two Intel PRO 10/100 NIC, IRQs are separated, an X100P so not to use ztdummy. Motherboard is an Intel

Yes, I am a newbie too. I am having a problem with meetme. From what I have seen it will work without a Digium card but with audio problems. My goal is just to see how it works not the quality of the audio. When I dial into the conference room the following message is played: "That is not a valid conference number." On the console I get: "unable to open pseudo channel". As

Hello, I have a problem with the meetme application, but I'm not sure if it's a bug or just a misuse. I'm trying to get a 3 way call system working as follow : A calls C B calls C C who's speaking with A or B, presses one keypad (only one) and the 2 incoming SIP (A, B) and C are redirected into a conference room. Therefore, I created an entry in the applicationmap

Hi, Has anyone tried to use gnokii to send/receive SMS messages via serial or USB with AT commands while running Asterisk? Some of my calls have a "scratchy sound" once in a while. It doesn't seem to be due to packet loss but some kind of interference (CPU is ok, etc.). I've noticed some coincidence in time between this scratchy sound and the gnokii process. I have a bash

Hi, I am using Debian OS kernel 2.6.22-3-amd64 and zaptel driver 1.4 with ztdummy module for meetme application. I use meetme with SIP channels. I have such problem that when one connects to the conference voice is "cut". Each voice sequence is disturbed. Does any one have similar issue and could give me some advice?? my extension.conf for meetme: ;switch =>

Hi all We run an * 1.2.4 under FreeBSD with ztdummy kernel module. zttest reports 99.9something % of accuracy, so timing should be fine. SIP connections work fine, but we have a strange problem with IAX2 connections. When an IAX2 call originates from the FreeBSD Asterisk to another Asterisk, the sound is scratchy (sounds a bit like a 50Hz ground loop). It's not a problem of the

What does it take to get ztdummy to work correctly? I have a new laptop HP HDX9200. I am running asterisk 1.4.19 and zaptel 1.4.9.2 Zaptel compiles fine. asterisk compiles fine. ztdummy loads asterisk runs. Problem is playback() does not work. So then I stop zaptel, asterisk runs and playback() now works. However, meetme()'s dont work. I need ztdummy I'm pretty sure for that. I am

Hi list, we have a dual Xeon server with 2GB RAM running Debian Etch 2.6.18.4-686 kernel. The server has 2 B410P cards plugged in. No other card. We installed Asterisk 1.4 trunk with zaptel trunk, ran make b410p, the install mISDN1.1.0 (for bug 9064) configure and compile Asterisk with chan_misdn, all is fine. In misdn-init.conf we have added option=1,master_clock. Asterisk is up and