similar to: Using locked PAP2 and PAP2-NA with Asterisk

I've got a Linksys PAP2 on my Vonage account with unlimited usage, but my softphone-addon account only has 500 minutes. Anyone ever try to setup their * to mimick the Linksys PAP2 ? Any comments or suggestions on what problems I might run into if I try? -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello, I nearly forgot about this mailing list! I accidentally bought a vonage enabled PAP2 to use on my asterisk, however it's locked and I have no access to the admin password. Anyone unlocked it before? Please send procedure. Make a cc to my address please. Thanks a million. Best regards, Twanny Azzopardi. Mob: ( 356 ) 79713618 Email: twanny@line.sytes.net Web: http://line.sytes.net

I have a handful of Linksys PAP2-NA's all talking nicely to Asterisk using standard telephones. I've been running them for the better part of this year. No complaints whatsoever. We chose the PAP2-NA's mainly due to cost and especially the ease of provisioning. In an effort to inexpensively bridge our office PBX (InterTel Axxess) to our VoIP network, we've opted to connect

Hi, I have 3 PAP2 connected to *, they work fine but there are some things which I would like to improve, some of them are: - double ring tone when placing a call (I hear two tones it seems like the PAP2 is generating it's own tone) - some kind of noise (like glitches or something) when I pick up the phone (seems like some polarity thing) - I'd like to keep the tone after

Hello, We use Asterisk with PAP2 and today we connected the FXS ports of PAP2 to CO ports of our Panasonic KX-TD1232. Problem is that Panasonic doesn't ring - that is doesn't ring every time the PAP2 is ringing. When we reset either Asterisk or the PAP2 it usually rings, but after couple of minutes it stops and only the automatic operator is answering - after 2 rings. We tried changing

I receieved my first PAP2-NA yesterday from our distributor(Tech Data). It installed pretty easily and has worked great so I went to order some more of these units today. When I logged into Tech Data this morning, the PAP2-NA was now marked as discontinued and no longer available and only the PAP2 version was available which is the Vonage branded version. :( I saw someone on the list say that

I am using mysql sipfriends and can't seem to get the MWI to work. From what I've read it seems this is not supported with that dynamic system, and probably never will be. I was thinking of just setting a cron job or something to check every minute for voicemail and set our sip NOTIFY messages as needed. Also, the PAP2-NA has the ability to reboot via a sip notify and I would like to be

Hello, I'm having intermittent STUN trouble. Every one out of perhaps 5 reboots the PAP2 contacts STUN ... on the other attempts it just skips that step all together. I have been verifying this using ethereal which shows the distinctive STUN server DNS lookup followed by about 10 STUN queries (when it works - when it doesn't it skips all that including the initial DNS lookup ...

Has anybody else experienced problems with the Linksys PAP2-NA's? I've now had two of them fail unexpectedly, with no apparent rhyme or reason, having gone into a RED power LED, with a solid blue ethernet LED. No response from the device either on the network or from the phone.... To make matters even crazier, the one that now failed was the one I received as a replacement for the

Hello Folks, I'm an Asterisk newbie, that being said I have managed to get an SPA941 working with 1.2.8. I've got some issues (like getting the voicemail button to work as it should, and making the message indicator light work) but overall I'm pretty happy. I'm now trying to get a PAP2-NA to work. I reset it, have admin access, updated the firmware, and have the same SIP settings

The best I can do so far (which appears to be a bit of a hack) is (<:0>S0), which says to add a '0' to the start of the string and dial immediately. This gives asterisk an extension dialled of '0', which isn't the 's' that i'd hoped for, but is a good start! (S0) by itself doesn't work, nor does (<:>S0). Any other suggestions? Thanks James >

Is there a way to configure the linksys pap2 to automatically connect to asterisk on lifting the handset (presumably into the 's' state)? Asterisk would then be listening for DTMF tones to figure out what to do rather than having to put a dial plan into each pap2. I think the pap2 is pretty much the same inside as a few of the sipura boxes so the same thing might work if anyone knows...

I am using my first PAP2 device from linksys. Used many polycom phones... I configured the PAP2 device with asterisk. I have the registration, thought I was good to go. Plugged in my Valcom 2924 public address analog connection, called the extension and I got busy... very strange I thought. I then looked at the status page of the PAP2 and it says the following Reg online and hook state OFF.

Has anyone made this work? For me everything is fine until I switch canreinvite form no to yes. What happens is that asterisk hangs on "attempting native bridge" ... from what I understand "attempting native bridge" means that the RTP is routed through asterisk (just without any codec translation) But it shouldn't do that ... right? ... canreinvite is set to yes ...

>Message: 7 >Date: Sun, 29 Oct 2006 22:00:22 +0100 >From: "Jose Limeres" <jlimeres@gmail.com> >Subject: [asterisk-users] Linksys PAP2: calling tone stops after 5 > tones >To: asterisk-users@lists.digium.com >Message-ID: > <2b3431b20610291300u420116e5scf9103d7dac54321@mail.gmail.com> >Content-Type: text/plain; charset=ISO-8859-1; format=flowed >

Hi All, I have my Asterisk box running with 6 extension all connected to CAT5 Grandstream phones. I'm trying to connect 2 extension on a different office across the hall by WIFI bridge using SMCWEBT-G configured as Ethernet client. If I connect the Grandstream to that box on the other office it works fine. If I connect the PAP2-NA, both extensions register with no problems with the Asterisk

We have some extensions in our dialplan that start with a star. We can dial them from Zap phones and SIP phones, but not from phones connected to a PAP2. After the user presses star follwed by two digits (our extensions are dialed with star followed by three digits) he hears a fast-busy that comes from the PAP2, not from Asterisk. This also happens with the builtin *8 (call pickup). In

Hi, anyone can confirm if the Linksys's ATA and Router (PAP2-NA and RT31P2-NA) have the same limitation of just one G.729 call like the Cisco ATA 186 ? I'm testing both appliances here and found this issue but could not confirm this anywhere (nothing on the manual, no document or post from any user about this). In my tests they use G.729 only on the first call and G.711 on the

Hi i am using pap2 phone adaptors as clients to connect to asterisk server i am able to make calls but i cannot access voice mail using phone or start recording while call is in progress and when i place a call to local sip extension there is a long pause ( 15 sec ) before the call gets dialled i assume that the problem would be due to the dial plan in PAP2 if so please help me changing it

Fry's Electronics has a new Linksys 2 line ATA box for sale for $59.99 retail. They have a version with a router for $89.99. We picked the non-router version up and it seems to be a rebadged Sipura SPA-2000. The box has a Vonage service package inside as well, but it does work with other services. The box also has a "User Guide" meant for end-users that is very well written [no