similar to: Limit fax tx speed of 'dumb' faxes??

I'm using Asterisk 1.09 with bristuff 0.2.0-RC8n, one BRI line and a Sipura SPA-2000. I have a HP LaserJet 3330mfp all-in-one. I can receive faxes but not send them. The faxes start whistling to each other but the transmission is stopped with a "communication error" To receive a fax I have this in my dialplan: exten => 0000000000,1,Ringing exten => 0000000000,2,zapEC(off)

We have an application for Asterisk that will require connecting 144 fax ports into the system. Faxes will route externally over a PRI. The 144 ports are for local fax machines within the building. Not all will be faxing simultaneously. We just need to be able to provide ports in the building to plug in lots of fax machines. The plan is to run an Asterisk server for about 100 phones and these

Everyone, I have a centos 5.10 machine set up to be a fax server using hylafax+ with three multitech MT5634ZBA modems. I am still in the testing phase of using this system for production, and during my tests I have detected a problem I have not been able to solve except for unplugging the modem from the usb port and plugging it back into the usb port. In the middle of a fax production of

I've gotten asterisk running fine with several Grandstream phones as well as linphone on my PC. Now the last step is configuring the multitech MVP 130s that I have to send outbound calls to the POTS lines attached to the MVP130s. I'm having issues with the outbound and inbound telephone book entries I believe. The multitechs work fine when configured to talk to each other at remote

I know the subject of faxing has been covered in some detail, but I was wondering if anyone has a hardware configuration similar to ours that has faxes working successfully and would be willing to share any settings/insight. We are unable to fax reliably with a Sipura 2100 connected to Asterisk. We do not route calls over the Internet and our network has very low latency. The Asterisk

Most people seem quite positive about Snom phones, I cannot share this opinion. The displays are dying quite often, and firmware is buggy. I have tried every firmware from 4.5 up to 5.x and 6.04 but keep having problems with phones locking up or rebooting during an ongoing conversation. REALLY annoying for a phone that is advertised / targeted as a business class phone

Hi, all I want to configure a few FXS ports in an Antribank-16 to be able to receive faxes sent throught a PRI: E1 ==>Zap * ==>FXS * ==>Fax machine My asterisk box has a Digium TE120P (for the PRI). Versions are *=> 1.4.17 | Zaptel=>1.4.8 | libpri=>1.4.5 The Astribank is not configured yet, because I am a little bit confused about how to do it. Let's say I configure

Is it possible in any way to use an Outlook contacts database as the source for the internal Asterisk database that is used for callerid lookups? Thanks!

I'm having a problem receiving incoming faxes and I'm hoping someone here can help me out. My system is a PBX in a Flash with one dahdi card for my incoming analog lines and another dahdi card for my analog devices (fax and modem). My dahdi-channels.conf file looks like: ; Autogenerated by /usr/sbin/dahdi_genconf on Tue Jun 23 14:56:24 2009 ; If you edit this file and execute

I'm planning a new * system which will utilize 48 stations (Polycom Soundpoint 501s mostly) and a dual span PRI card and I have some questions. The system will host MeetMe conferences of 10-15 users on a regular basis and see fairly high usage as it is going into a medical setting. 1. I haven't built a system this big before, will a processor such as the Intel Pentium D 830 3.0GHz / 2MB

Hi list! I'm sure the topic has been discussed but I could not find what I was looking for. What would be the best / easiest VPN software solution. I would like to install vpn software on the * server for roadwarriors to connect to with laptops running windows. Ideally the vpn solution will not require any additional software on the client side but will use IPSEC. (Ofcourse call quality

Hi list! I have some sip phones and Sipura ATA 2000's. However after dialling a number I need to dial a # to control a device. When I dial # Asterisk kicks in and puts the call on hold. How can I change this? Thx!! Remco

We recently had a customer install that went horribly wrong. Serious echo (pots lines into a cac cb) that, although * did a good job getting rid of alot of it, could not get rid of it all. We tried everything, every canceller, gain setting, etc... combination possible to no avail. Both the vegastream and mediatrix boxes also could not get rid of all of the echo. So, on an off chance, we

Hi List, I have a Multitech H323 Gateway MVP400 box with 1 phone on port FXO 1. I have Asterisk ruuning in Fedora Core 3. Both are in the same network. But I can't figure what I have to do in Asterisk to make that box work. What files I have to configure? Can anyone help me? I will really appreaciate youu help. Luis. _________________________________________________________ Do You Yahoo!?

Hi All, I'm new to asterisk, can I use asterisk with a Multitech mvp 210? Thanks, Steve

Hi list ! Is it possible to show the used Useragent of a peer that registered with Asterisk? It's being saved obviously because the console says so when a phone is registering but sip show peers doesn't show it? Is there any other way to view it? Thanks!

It's been many years, but it seems that I have to receive a fax and might have to send one too. Is there a way to do this on CentOS 5.5? (Hope so.) tia. -- Anything is easy if you know how to do it.

Hi list! The stability of * with fax (or the lack of it) is causing me headaches. To solve it, I was thinking to put a TE205P card in the * box, connect the E1 pri on one port and a channelbank (I was thinking of the Rhino) on the other port in T1 mode. (Has anyone tried this??) The TE205P supports channel bridging which sounded like the ideal (but not cheap) solution when combined with a

Hi list! What exactly is the meaning / function of the pridialplan & prilocaldialplan? I've been trying to find out what the different possibilities for these settings are but couldn't find a clear answer. The possible parameters I could find are are : local,unknown,dynamic,national,international and maybe there are more? Thanks!

Hello, I have been retained by a Building Management Company to install a combined Voice/Data solution for a Tennated Office Space. This space will rent offices, with telephone and internet service to inviduals or small groups of individuals. As fate would have it, the service will be provided in a building where we have a major Pop, with a DS-3 worth of ISDN PRI circuits, 345 megs of